View DS3100GN_4725158.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

19-4546; Rev 9; 5/09
DEMO KIT AVAILABLE
DS3100 Stratum 2/3E/3 Timing Card IC
www.maxim-ic.com
GENERAL DESCRIPTION
When paired with an external TCXO or OCXO, the DS3100 is a complete central timing and synchronization solution for SONET/SDH network elements. With two multiprotocol BITS/SSU receivers and 14 input clocks, the device directly accepts both external timing and line timing from a large number of line cards. All input clocks are continuously monitored for frequency accuracy and activity. Any two of the input clocks can be selected as the references for the two core DPLLs. The T0 DPLL complies with the Stratum 2, 3E, 3, 4E and 4 requirements of GR1244, GR-253, G.812 Types I - IV, G.813 and G.8262. From the output of the core DPLLs, a wide variety of output clock frequencies and frame pulses can be produced simultaneously on the 11 output clock pins. Two DS3100 devices can be configured in a master/slave arrangement for timing card equipment protection. The DS3100 registers and I/O pins are backward compatible with Semtech's ACS8520 and ACS8530 timing card ICs.
FEATURES
Synchronization Subsystem for Stratum 2, 3E, 3, 4E and 4 plus SMC, SEC and EEC - Meets Requirements of GR-1244 Stratum 2 - 4, GR-253, G.812 Types I - IV, G.813 and G.8262 - Stratum 2, 3E or 3 Holdover Accuracy with Suitable External Oscillator - Programmable Bandwidth, 0.5mHz to 70Hz - Hitless Reference Switching on Loss of Input - Phase Build-Out and Transient Absorption - Locks to and Generates 125MHz for Gigabit Synchronous Ethernet per ITU-T G.8261 14 Input Clocks - 10 CMOS/TTL Inputs Accept 2kHz, 4kHz, and Any Multiple of 8kHz Up to 125MHz - Two LVDS/LVPECL/CMOS/TTL Inputs Accept Nx8kHz Up to 125MHz Plus 155.52MHz - Two 64kHz Composite Clock Receivers - Continuous Input Clock Quality Monitoring - Separate 2/4/8kHz Frame Sync Input 11 Output Clocks - Five CMOS/TTL Outputs Drive Any Internally Produced Clock Up to 77.76MHz - Two LVDS Outputs Each Drive Any Internally Produced Clock Up to 311.04MHz - One 64kHz Composite Clock Transmitter - One 1.544MHz/2.048MHz Output Clock - Two Sync Pulses: 8kHz and 2kHz - Output Clock Rates Include 2kHz, 8kHz, NxDS1, NxDS2, DS3, NxE1, E3, 6.48MHz, 19.44MHz, 38.88MHz, 51.84MHz, 62.5MHz, 77.76MHz, 125MHz, 155.52MHz, 311.04MHz Two Multiprotocol BITS/SSU Transceivers - Receive and Transmit DS1, E1, 2048kHz, and 6312kHz Timing Signals - Insert and Extract SSM Messages (DS1, E1) - Automatically Invalidate Clocks on LOS, OOF, AIS, and Other Defects Internal Compensation for Master Clock Oscillator Frequency Accuracy Processor Interface: 8-Bit Parallel or SPI Serial 1.8V Operation with 3.3V I/O (5V Tolerant)
APPLICATIONS
SONET/SDH ADMs, MSPPs, and MSSPs Digital Cross-Connects DSLAMs Service Provider Routers
FUNCTIONAL DIAGRAM
TIMING FROM LINE CARDS (VARIOUS RATES) 14 TIMING FROM BITS/SSU (DS1, E1, CC, ETC.) LOCAL TCXO OR OCXO TIMING TO BITS/SSU (DS1, E1, CC, ETC.)
DS3100
SONET/SDH SYNCHRONIZATION IC
2
2
11
TIMING TO LINE CARDS (VARIOUS RATES)
CONTROL STATUS

ORDERING INFORMATION
PART DS3100GN DS3100GN+ TEMP RANGE -40C to +85C -40C to +85C PIN-PACKAGE 256 CSBGA (17mm) 2 256 CSBGA (17mm) 2
+Denotes a lead(Pb)-free/RoHS-compliant package.
Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata.
1 of 227
DS3100
TABLE OF CONTENTS
1. STANDARDS COMPLIANCE ................................................................................................7 2. BLOCK DIAGRAM.................................................................................................................8 3. APPLICATION EXAMPLE .....................................................................................................9 4. DETAILED DESCRIPTION ..................................................................................................10 5. DETAILED FEATURES .......................................................................................................12
5.1 5.2 5.3 5.4 5.5 5.6 T0 DPLL FEATURES ....................................................................................................................12 T4 DPLL FEATURES ....................................................................................................................12 INPUT CLOCK FEATURES..............................................................................................................12 OUTPUT CLOCK FEATURES ..........................................................................................................13 REDUNDANCY FEATURES.............................................................................................................13 BITS TRANSCEIVER FEATURES ....................................................................................................13
5.6.1 5.6.2 5.6.3 General......................................................................................................................................... 13 Receiver ....................................................................................................................................... 13 Transmitter ................................................................................................................................... 14
5.7 5.8
COMPOSITE CLOCK I/O FEATURES...............................................................................................14 GENERAL FEATURES ...................................................................................................................14
6. PIN DESCRIPTIONS............................................................................................................15 7. FUNCTIONAL DESCRIPTION .............................................................................................24
7.1 7.2 7.3 7.4 7.5 OVERVIEW...................................................................................................................................24 DEVICE IDENTIFICATION AND PROTECTION....................................................................................25 LOCAL OSCILLATOR AND MASTER CLOCK CONFIGURATION ...........................................................25 INPUT CLOCK CONFIGURATION.....................................................................................................26
7.4.1 7.4.2 7.5.1 7.5.2 7.5.3 7.5.4 Signal Format Configuration......................................................................................................... 26 Frequency Configuration .............................................................................................................. 28 Frequency Monitoring................................................................................................................... 29 Activity Monitoring ........................................................................................................................ 29 Selected Reference Activity Monitoring........................................................................................ 30 Composite Clock Inputs................................................................................................................ 30 Priority Configuration .................................................................................................................... 31 Automatic Selection Algorithm ..................................................................................................... 31 Forced Selection........................................................................................................................... 32 Ultra-Fast Reference Switching.................................................................................................... 32 External Reference Switching Mode ............................................................................................ 32 Output Clock Phase Continuity During Reference Switching....................................................... 33 T0 DPLL State Machine ............................................................................................................... 33 T4 DPLL State Machine ............................................................................................................... 36 Bandwidth..................................................................................................................................... 37 Damping Factor ............................................................................................................................ 38 Phase Detectors ........................................................................................................................... 38 Loss of Phase Lock Detection...................................................................................................... 39 Phase Monitor and Phase Build-Out ............................................................................................ 40 Input to Output Phase Adjustment ............................................................................................... 41 Phase Recalibration ..................................................................................................................... 41 Frequency and Phase Measurement ........................................................................................... 41 Input Wander and Jitter Tolerance ............................................................................................... 42 2 of 227
INPUT CLOCK QUALITY MONITORING ............................................................................................29
7.6
INPUT CLOCK PRIORITY, SELECTION, AND SWITCHING ..................................................................31
7.6.1 7.6.2 7.6.3 7.6.4 7.6.5 7.6.6
7.7
DPLL ARCHITECTURE AND CONFIGURATION.................................................................................33
7.7.1 7.7.2 7.7.3 7.7.4 7.7.5 7.7.6 7.7.7 7.7.8 7.7.9 7.7.10 7.7.11
19-4546; Rev 9; 5/09
DS3100 7.7.12 Jitter and Wander Transfer........................................................................................................... 42 7.7.13 Output Jitter and Wander ............................................................................................................. 43
7.8 7.9
OUTPUT CLOCK CONFIGURATION .................................................................................................44
7.8.1 7.8.2 7.9.1 7.9.2 7.9.3 7.10.1 7.10.2 7.10.3 7.10.4 7.10.5 7.10.6 7.10.7 7.10.8 Signal Format Configuration......................................................................................................... 45 Frequency Configuration .............................................................................................................. 45 Master-Slave Pin Feature............................................................................................................. 55 Master-Slave Output Clock Phase Alignment .............................................................................. 55 Master-Slave Frame and Multi-Frame Alignment with the SYNC2K Pin ..................................... 56 Master Clock Connections ........................................................................................................... 59 Receiver Clock Connections ........................................................................................................ 59 Transmitter Clock Connections .................................................................................................... 61 Line Interface Unit ........................................................................................................................ 62 DS1 Synchronization Interface..................................................................................................... 68 E1 Synchronization Interface ....................................................................................................... 70 G.703 2048kHz Synchronization Interface................................................................................... 72 G.703 Appendix II 6312kHz Japanese Synchronization Interface............................................... 73
EQUIPMENT REDUNDANCY CONFIGURATION .................................................................................54
7.10 MULTIPROTOCOL BITS TRANSCEIVERS ........................................................................................58
7.11 COMPOSITE CLOCK RECEIVERS AND TRANSMITTER ......................................................................74
7.11.1 IC1 and IC2 Receivers ................................................................................................................. 75 7.11.2 OC8 Transmitter ........................................................................................................................... 75
7.12 MICROPROCESSOR INTERFACES ..................................................................................................77
7.12.1 Parallel Interface Modes............................................................................................................... 77 7.12.2 SPI Interface Mode....................................................................................................................... 77
7.13 RESET LOGIC ..............................................................................................................................79 7.14 POWER-SUPPLY CONSIDERATIONS ..............................................................................................80 7.15 INITIALIZATION .............................................................................................................................80
8. REGISTER DESCRIPTIONS ...............................................................................................81
8.1 8.2 8.3 8.4 8.5 9.1 9.2 9.3 9.4 10.1 10.2 10.3 10.4 10.5 10.6 10.7 STATUS BITS ...............................................................................................................................81 CONFIGURATION FIELDS ..............................................................................................................81 MULTIREGISTER FIELDS ...............................................................................................................81 CORE REGISTER DEFINITIONS......................................................................................................82 BITS TRANSCEIVER REGISTER DEFINITIONS...............................................................................147 JTAG DESCRIPTION ..................................................................................................................198 JTAG TAP CONTROLLER STATE MACHINE DESCRIPTION............................................................199 JTAG INSTRUCTION REGISTER AND INSTRUCTIONS ....................................................................201 JTAG TEST REGISTERS.............................................................................................................202 DC CHARACTERISTICS...............................................................................................................203 INPUT CLOCK TIMING .................................................................................................................207 OUTPUT CLOCK TIMING .............................................................................................................207 BITS TRANSCEIVER TIMING .......................................................................................................208 PARALLEL INTERFACE TIMING ....................................................................................................210 SPI INTERFACE TIMING ..............................................................................................................213 JTAG INTERFACE TIMING...........................................................................................................214
9. JTAG TEST ACCESS PORT AND BOUNDARY SCAN....................................................198
10. ELECTRICAL CHARACTERISTICS..................................................................................203
11. PIN ASSIGNMENTS ..........................................................................................................215 12. PACKAGE INFORMATION ...............................................................................................221
12.1 256-PIN CSBGA (17MM X 17MM) ..............................................................................................221
13. THERMAL INFORMATION................................................................................................222
19-4546; Rev 9; 5/09 3 of 227
DS3100
14. GLOSSARY .......................................................................................................................223 15. ACRONYMS AND ABBREVIATIONS ...............................................................................224 16. TRADEMARK ACKNOWLEDGEMENTS ..........................................................................224 17. DATA SHEET REVISION HISTORY..................................................................................225
19-4546; Rev 9; 5/09
4 of 227
DS3100
LIST OF FIGURES
Figure 2-1. DS3100 Block Diagram ............................................................................................................................. 8 Figure 3-1. Typical Application Example ..................................................................................................................... 9 Figure 7-1. T0 DPLL State Transition Diagram ......................................................................................................... 34 Figure 7-2. T4 DPLL State Transition Diagram ......................................................................................................... 37 Figure 7-3. Typical MTIE for T0 DPLL Output ........................................................................................................... 43 Figure 7-4. Typical TDEV for T0 DPLL Output .......................................................................................................... 44 Figure 7-5. DPLL Block Diagram ............................................................................................................................... 46 Figure 7-6. OC10 8kHz Options ................................................................................................................................ 54 Figure 7-7. BITS Transceiver Block Diagram ............................................................................................................ 58 Figure 7-8. BITS Transceiver Master Clock PLL Block Diagram .............................................................................. 59 Figure 7-9. BITS Transmitter Clock Mux Block Diagram........................................................................................... 60 Figure 7-10. BITS Transceiver External Components............................................................................................... 62 Figure 7-11. Jitter Tolerance, DS1 Mode .................................................................................................................. 63 Figure 7-12. Jitter Tolerance, E1 and 2048kHz Modes ............................................................................................. 64 Figure 7-13. Transmit Pulse Template, DS1 Mode ................................................................................................... 66 Figure 7-14. Transmit Pulse Template, E1 Mode...................................................................................................... 66 Figure 7-15. Transmit Pulse Template, 2048kHz Mode ............................................................................................ 67 Figure 7-16. FAS/Si/RAI/Sa Source Logic................................................................................................................. 72 Figure 7-17. GR-378 Composite Clock Pulse Mask.................................................................................................. 76 Figure 7-18. SPI Clock Polarity and Phase Options.................................................................................................. 78 Figure 7-19. SPI Bus Transactions............................................................................................................................ 79 Figure 9-1. JTAG Block Diagram............................................................................................................................. 198 Figure 9-2. JTAG TAP Controller State Machine .................................................................................................... 200 Figure 10-1. Recommended Termination for LVDS Pins ........................................................................................ 204 Figure 10-2. Recommended Termination for LVPECL Pins.................................................................................... 205 Figure 10-3. Recommended External Components for AMI Composite Clock Pins ............................................... 206 Figure 10-4. BITS Receiver Timing Diagram........................................................................................................... 208 Figure 10-5. BITS Transmitter Timing Diagram....................................................................................................... 209 Figure 10-6. Parallel Interface Timing Diagram (Nonmultiplexed) .......................................................................... 211 Figure 10-7. Parallel Interface Timing Diagram (Multiplexed) ................................................................................. 212 Figure 10-8. SPI Interface Timing Diagram ............................................................................................................. 213 Figure 10-9. JTAG Timing Diagram......................................................................................................................... 214 Figure 11-1. DS3100 Pin Assignment--Left Half .................................................................................................... 219 Figure 11-2. DS3100 Pin Assignment--Right Half.................................................................................................. 220
19-4546; Rev 9; 5/09
5 of 227
DS3100
LIST OF TABLES
Table 1-1. Applicable Telecom Standards................................................................................................................... 7 Table 6-1. Input Clock Pin Descriptions .................................................................................................................... 15 Table 6-2. Output Clock Pin Descriptions.................................................................................................................. 16 Table 6-3. BITS Receiver Pin Descriptions ............................................................................................................... 17 Table 6-4. BITS Transmitter Pin Descriptions ........................................................................................................... 18 Table 6-5. Global Pin Descriptions ............................................................................................................................ 19 Table 6-6. Parallel Interface Pin Descriptions ........................................................................................................... 20 Table 6-7. SPI Bus Mode Pin Descriptions ............................................................................................................... 21 Table 6-8. JTAG Interface Pin Descriptions .............................................................................................................. 21 Table 6-9. General-Purpose I/O Pin Descriptions ..................................................................................................... 21 Table 6-10. Power-Supply Pin Descriptions .............................................................................................................. 22 Table 7-1. GR-1244 Stratum 2/3E/3 Stability Requirements..................................................................................... 25 Table 7-2. Input Clock Capabilities ............................................................................................................................ 27 Table 7-3. Locking Frequency Modes ....................................................................................................................... 28 Table 7-4. Default Input Clock Priorities .................................................................................................................... 31 Table 7-5. Damping Factors and Peak Jitter/Wander Gain....................................................................................... 38 Table 7-6. T0 Adaptation for T4 Phase Measurement Mode .................................................................................... 42 Table 7-7. Output Clock Capabilities ......................................................................................................................... 44 Table 7-8. Digital1 and Digital2 Frequencies............................................................................................................. 47 Table 7-9. APLL Frequency to Output Frequencies (T0 and T4) .............................................................................. 48 Table 7-10. T0 APLL Frequency to T0 Path Configuration ....................................................................................... 48 Table 7-11. T4 APLL Frequency to T4 Path Configuration ....................................................................................... 49 Table 7-12. OC1 to OC7 Output Frequency Selection .............................................................................................. 50 Table 7-13. Possible Frequencies for OC1 to OC7 ................................................................................................... 50 Table 7-14. Equipment Redundancy Methodology ................................................................................................... 54 Table 7-15. Transformer Specifications..................................................................................................................... 67 Table 7-16. DS1 Alarm Criteria.................................................................................................................................. 68 Table 7-17. E1 Alarm Criteria .................................................................................................................................... 70 Table 7-18. E1 Sync and Resync Criteria ................................................................................................................. 70 Table 7-19. 2048kHz Synchronization Interface Specification .................................................................................. 73 Table 7-20. 6312kHz Synchronization Interface Specification .................................................................................. 73 Table 7-21. Composite Clock Variations ................................................................................................................... 74 Table 7-22. GR-378 Composite Clock Interface Specification .................................................................................. 76 Table 7-23. G.703 Synchronization Interfaces Specification..................................................................................... 76 Table 7-24. Microprocessor Interface Modes ............................................................................................................ 77 Table 8-1. Top-Level Memory Map............................................................................................................................ 81 Table 8-2. Core Register Map ................................................................................................................................... 82 Table 8-3. BITS Transceiver Register Map ............................................................................................................. 147 Table 9-1. JTAG Instruction Codes ......................................................................................................................... 201 Table 9-2. JTAG ID Code ........................................................................................................................................ 202 Table 10-1. Recommended DC Operating Conditions ............................................................................................ 203 Table 10-2. DC Characteristics................................................................................................................................ 203 Table 10-3. CMOS/TTL Pins ................................................................................................................................... 204 Table 10-4. LVDS Pins ............................................................................................................................................ 204 Table 10-5. LVPECL Pins........................................................................................................................................ 205 Table 10-6. AMI Composite Clock Pins ................................................................................................................... 206 Table 10-7. Recommended External Components for Output Clock OC8.............................................................. 206 Table 10-8. Input Clock Timing................................................................................................................................ 207 Table 10-9. Input Clock to Output Clock Delay ....................................................................................................... 207 Table 10-10. Output Clock Phase Alignment, Frame Sync Alignment Mode......................................................... 207 Table 10-11. BITS Receiver Timing......................................................................................................................... 208 Table 10-12. BITS Transmitter Timing..................................................................................................................... 209 Table 10-13. Parallel Interface Timing..................................................................................................................... 210 Table 10-14. SPI Interface Timing ........................................................................................................................... 213 Table 10-15. JTAG Interface Timing........................................................................................................................ 214 Table 11-1. Pin Assignments Sorted by Signal Name............................................................................................. 215 Table 13-1. Thermal Properties, Natural Convection .............................................................................................. 222 19-4546; Rev 9; 5/09 6 of 227
DS3100
1.
STANDARDS COMPLIANCE
Table 1-1. Applicable Telecom Standards
SPECIFICATION ANSI T1.101 T1.102 T1.107 T1.231.02 T1.403 TIA/EIA-644-A AT&T TR62411 ETSI EN 300 417-6-1 EN 300 462-3-1 EN 300 462-5-1 IEEE IEEE 1149.1 ITU-T G.703 G.704 G.706 G.775 G.781 G.783 G.812 G.813 G.823 G.824 G.825 G.8262 O.162 TELCORDIA GR-253-CORE GR-378-CORE GR-499-CORE GR-1244-CORE SPECIFICATION TITLE Synchronization Interface Standard, 1999 Digital Hierarchy--Electrical Interfaces, 1993 Digital Hierarchy--Formats Specification, 1995 Digital Hierarchy--Layer 1 In-Service Digital Transmission Performance Monitoring, 2003 Network and Customer Installation Interfaces--DS1 Electrical Interface, 1999 Electrical Characteristics of Low Voltage Differential Signaling (LVDS) Interface Circuits, 2001 ACCUNET(R) T1.5 Service Description and Interface Specification (12/1990) Transmission and Multiplexing (TM); Generic Requirements of Transport Functionality of Equipment; Part 6-1: Synchronization Layer Functions, v1.1.3 (1999-05) Transmission and Multiplexing (TM); Generic Requirements for Synchronization Networks; Part 3-1: The Control of Jitter and Wander within Synchronization Networks, v1.1.1 (1998-05) Transmission and Multiplexing (TM); Generic Requirements for Synchronization Networks; Part 5-1: Timing Characteristics of Slave Clocks Suitable for Operation in Synchronous Digital Hierarchy (SDH) Equipment, v1.1.1 (1998-05) Standard Test Access Port and Boundary-Scan Architecture, 1990 Physical/Electrical Characteristics of Hierarchical Digital Interfaces (11/2001) Synchronous Frame Structures Used at 1544, 6312, 2048, 8448 and 44736 kbit/s Hierarchical Levels (10/1998) Frame Alignment and Cyclic Redundancy Check (CRC) Procedures Relating to Basic Frame Structures Defined in Recommendation G.704 (1991) Loss of Signal (LOS) and Alarm Indication Signal (AIS) and Remote Defect Indication (RD) Defect Detection and Clearance Criteria for PDH Signals (10/1998) Synchronization Layer Functions (06/1999) ITU G.783 Characteristics of Synchronous Digital Hierarchy (SDH) Equipment Functional Blocks (10/2000 plus Amendment 1 06/2002 and Corrigendum 2 03/2003) Timing Requirements of Slave Clocks Suitable for Use as Node Clocks in Synchronization Networks (06/1998) Timing characteristics of SDH equipment slave clocks (SEC) (03/2003) The Control of Jitter and Wander within Digital Networks which are Based on the 2048kbps Hierarchy (03/2000) The Control of Jitter and Wander within Digital Networks which are Based on the 1544kbps Hierarchy (03/2000) The Control of Jitter and Wander within Digital Networks which are Based on the Synchronous Digital Hierarchy (SDH) (03/2000) Timing characteristics of synchronous Ethernet equipment slave clock (EEC) (08/2007) Equipment to Perform In-Service Monitoring on 2048, 8448, 34,368 and 139,264 kbit/s Signals (10/1992) SONET Transport Systems: Common Generic Criteria, Issue 3, September 2000 Generic Requirements for Timing Signal Generators, Issue 2, February 1999 Transport Systems Generic Requirements (TSGR) Common Requirements, Issue 2, December 1998 Clocks for the Synchronized Network: Common Generic Criteria, Issue 2, December 2000
19-4546; Rev 9; 5/09
7 of 227
DS3100
2.
BLOCK DIAGRAM
Figure 2-1. DS3100 Block Diagram
JTRST JTMS JTCLK JTDI JTDO IC1A IC2A IC1 IC2 IC3 IC4 IC5 POS/NEG IC6 POS/NEG IC7 IC8 IC9 IC10 IC11 IC12 IC13 IC14 RTIP1 RRING1 MCLK1 RCLK1 ROUT1 RSER1 RESREF RTIP2 TRING2 RRING2 MCLK2 RCLK2 ROUT2 RSER2
CC Rx
CC Rx
JTAG
OC1 OC2 OC3 OC4 OC5 OC6 POS/NEG OC7 POS/NEG
CC Tx Input Clock Selector, Divider and Monitor BITS/SSU Receiver 1 T4 DPLL Output Clock Synthesizer and Selector
OC8 POS/NEG OC9 OC10 OC11 TTIP1 TRING1
DS3100
BITS/SSU Transmitter 1
THZE1 TCLK1 TOUT1 TIN1 TSER1
T0 DPLL SSM
SSM
TTIP2
BITS/SSU Receiver 2
Microprocessor Port (8-bit Parallel or SPI Serial) and HW Control and Status Pins
Master Clock Generator WDT
BITS/SSU Transmitter 2
THZE2 TCLK2 TOUT2 TIN2 TSER2
SSM
HIZ RST IFSEL[2:0] CS WR / R/W RD / DS ALE A[8:0] AD7 / CPOL AD6 / CPHA AD[5:3] AD2 / SCLK AD1 / SDI AD0 / SDO RDY INTREQ MASTSLV SONSDH SRCSW SRFAIL GPIO[4:1] SYNC2K WDT
SSM
TCXO or OCXO
REFCLK
See Figure 7-5 on page 46 for a detailed view of the T0 and T4 DPLLs and the Output Clock Synthesizer and Selector block. See Figure 7-7 on page 58 for a detailed view of the BITS Receiver and BITS Transmitter blocks.
19-4546; Rev 9; 5/09
8 of 227
DS3100
3.
APPLICATION EXAMPLE
Figure 3-1. Typical Application Example
activty and frequency monitoring, select highest priority valid input create derived DS1 or E1/2048 kHz clock from 19.44 MHz frequency locked to line clock create DS1/E1 frames, insert SSMs, transmit DS1, E1 or 2048 kHz sync signal
Backplane
Timing Card (1 of 2)
micro controller
N <0>
DS3100
Monitor, Divider, Selector T4 DPLL T4 APLL
BITS Tx BITS Tx BITS Rx
DS1, E1 or 2048 kHz
to BITS/SSU
TCXO or OCXO
N
T0 APLL
T0 DPLL
typically 19.44 MHz point-to-point or multidrop buses
N <0> N
Monitor, Divider, Selector
from BITS/SSU
BITS Rx
DS1, E1 or 2048 kHz
Timing Card (2 of 2) Identical to Timing Card 1
clock/data recovery, equalizer, framer, extract SSMs Stratum 2, 3E, or 3: jitter/wander filtering, hitless switching, phase adjust, holdover
<1> <1> <1> <1>
Line Card (1 of N)
divide line clock down to backplane rate, send to timing cards

Line Card (N of N)
DPLL APLL
to port SERDES
select best system clock, hitless switching, basic holdover
clock multiplication, jitter cleanup
19-4546; Rev 9; 5/09
9 of 227
DS3100
4.
DETAILED DESCRIPTION
Figure 2-1 illustrates the blocks described in this section and how they relate to one another. Section 5 provides a detailed feature list. The DS3100 is a complete timing card IC for systems with SONET/SDH ports. At the core of this device are two digital phase-locked loops (DPLLs) labeled T0 and T4 1. DPLL technology makes uses of digital-signal processing (DSP) and digital-frequency synthesis (DFS) techniques to implement PLLs that are precise, flexible, and have consistent performance over voltage, temperature, and manufacturing process variations. The DS3100's DPLLs are digitally configurable for input and output frequencies, loop bandwidth, damping factor, pull-in/hold-in range, and a variety of other factors. Both DPLLs can directly lock to many common telecom frequencies and also can lock at 8kHz to any multiple of 8kHz up to 155.52MHz. The DPLLs can also tolerate and filter significant amounts of jitter and wander. The T0 DPLL is responsible for generating the system clocks used to time the outgoing traffic interfaces of the system (SONET/SDH, synchronous Ethernet, etc.). To perform this role in a variety of systems with diverse performance requirements, the T0 DPLL has a sophisticated feature set and is highly configurable. T0 can automatically transition among free-run, locked and holdover states all without software intervention. In free-run, T0 generates a stable, low-noise clock with the same frequency accuracy as the external oscillator connected to the REFCLK pin. With software calibration the DS3100 can even improve the accuracy to within 0.02 ppm. When an input reference has been validated, T0 transitions to the locked state in which its output clock accuracy is equal to -11 the accuracy of the input reference. While in the locked state, T0 acquires a high-accuracy (3.85 x10 ) long-term average frequency value to use as the holdover frequency. When its selected reference fails, T0 can very quickly detect the failure and enter the holdover state to avoid affecting its output clock. From holdover it can automatically switch to the next highest priority input reference, again without affecting its output clock (hitless switching). Switching among input references can be either revertive or nonrevertive. When all input references are lost, T0 stays in holdover in which it generates a stable low-noise clock with initial frequency accuracy equal to its stored holdover value and drift performance determined by the quality of the external oscillator. With a suitable local oscillator the T0 DPLL provides holdover performance suitable for all applications up to and including Stratum 2. T0 can also perform phase build-outs and fine-granularity output clock phase adjustments. The T4 DPLL has a much less demanding role to play and therefore is much simpler than T0. Often T4 is used as a frequency converter to create a derived DS1- or E1-rate clock (frequency locked to an incoming SONET/SDH port) to be sent to a nearby BITS Timing Signal Generator (TSG, Telcordia terminology) or Synchronization Supply Unit (SSU, ITU-T terminology). In other cases T4 is phase-locked to T0 and used as a frequency converter to produce additional output clock rates for use within the system, such as NxDS1, NxE1, NxDS2, DS3, E3, or 125MHz for synchronous Ethernet. T4 can also be configured as a measuring tool to measure the frequency of an input reference or the phase difference between two input references. At the front end of both the T0 and T4 DPLLs is the Input Clock Selector, Divider, and Monitor (ICSDM) block. This block continuously monitors as many as 14 different input clocks of various frequencies for activity and frequency accuracy. In addition, ICSDM maintains separate input clock priority tables for the T0 and T4 DPLLs and can automatically select and provide the highest priority valid clock to each DPLL without any software intervention. The ICSDM block can also divide the selected clock down to 8kHz if required by the DPLL. In addition to digital clock signals from system line cards, the DS3100 can also directly receive up to two 64kHz composite clock signals on its IC1A and IC2A pins and up to two DS1, E1, 2048kHz, or 6312kHz synchronization signals using its BITS receivers. These signals typically come from a nearby BITS Timing Signal Generator or SSU to provide external timing to the system. The BITS receivers are full-featured LIU receivers and framers capable of recovering clock and data from both short-haul and long-haul signals, finding DS1/E1 frame, extracting incoming SSM messages, and reporting both SSMs and performance defects (LOS, OOF, AIS, RAI) to system software. The recovered clock from each BITS receiver can be connected to any of the 14 input clocks of the ICSDM block for monitoring, optional dividing, and selection as the reference for either of the DPLLs. The BITS receivers are tightly coupled to the ICSDM block, and the DS3100 can be configured to automatically disqualify input clocks from BITS receivers (or take other actions) when defects are detected. The analog front-ends of the BITS receivers are state-
1
These names are adapted from output ports of the SETS function specified in ITU and ETSI standards such as ETSI EN 300 462-2-1.
19-4546; Rev 9; 5/09
10 of 227
DS3100 of-the-art LIU receivers with software-selectable termination and high-impedance inputs to support redundant timing cards without relays in the signal path. The Output Clock Synthesizer and Selector (OCSS) block shown in Figure 2-1 contains the T0 output APLL, the T4 output APLL, clock divider logic, and additional output DFS blocks. The T0 and T4 APLLs multiply the clock rates from the DPLLs by four and simulataneously attenuate jitter. Using the different settings of the T0 and T4 DPLLs and the output divider logic, the DS3100 can produce more than 60 different output frequencies including common SONET/SDH, PDH and synchronous Ethernet rates plus 2kHz and 8kHz frame pulses. In addition to creating digital clock signals for use within the system, the DS3100 can also directly transmit one composite clock signal on its OC8 pin and up to two DS1, E1, or 2048kHz synchronization signals using its BITS transmitters. These signals typically convey the recovered timing from one SONET/SDH port to a nearby BITS timing-signal generator or SSU which in turn distributes timing to the whole central office.The BITS transmitters are full-featured frame formatters and LIU transmitters capable of generating DS1/E1 frames, inserting incoming SSM messages, and driving both short-haul and long-haul signals. Any of the output clock signals can be connected to either of the BITS transmitters for use as the transmission clock. The analog front-ends of the BITS transmitters are state-of-the-art LIU transmitters with software-selectable termination and high-impedance outputs to support redundant timing cards without relays in the signal path. The entire chip is clocked from the external oscillator connected to the REFCLK pin. Thus the free-run and holdover stability of the DS3100-based timing card is entirely a function of the stability of the external oscillator, the performance of which can be selected to match the application: TCXO, OCXO, double-oven OCXO, etc. The 12.8MHz clock from the external oscillator is multiplied by 16 by the Master Clock Generator block to create the 204.8MHz master clock used by the rest of the device. Since every block on the device depends on the master clock and therefore the local oscillator clock for proper operation, the master clock generator has a watchdog timer (WDT) function that can be used to signal a local microprocessor in the event of a local oscillator clock failure. The DS3100 also has several features to support master/slave timing card redundancy and protection. Two DS3100 devices on redundant cards can be configured to maintain the same priority tables, choose the same input references, and generate output clocks and frame syncs with the same frequency and phase.
19-4546; Rev 9; 5/09
11 of 227
DS3100
5.
5.1

DETAILED FEATURES
T0 DPLL Features
High-resolution DPLL plus low-jitter output APLL Sophisticated state machine automatically transitions between free-run, locked, and holdover states Revertive or nonrevertive reference selection algorithm Programmable bandwidth in 18 steps from 0.5mHz to 70Hz Separately configurable acquisition bandwidth and locked bandwidth Programmable damping factor to balance lock time with peaking: 1.2, 2.5, 5, 10, or 20 Multiple phase detectors: phase/frequency, early/late, and multicycle Phase/frequency locking (360 capture) or nearest-edge phase locking (180 capture) Multi-cycle phase detection and locking (up to 8191UI) improves jitter tolerance and lock time Phase build-out in response to input phase transients (1 to 3.5s) Phase build-out in response to reference switching Less than 5ns output clock phase transient during phase build-out Output phase adjustment up to 200ns in 6ps steps with respect to selected input reference High-resolution frequency and phase measurement Holdover frequency averaging with 8- or 110-minute intervals APLL frequency options suitable for N x 19.44MHz, N x DS1, and N x E1 Low-jitter frame sync (8kHz) and multiframe sync (2kHz) outputs on OC10 and OC11 2kHz and 8kHz clocks available on OC1 through OC7 with programmable polarity and pulse width
5.2

T4 DPLL Features
High-resolution DPLL plus low-jitter output APLL Programmable bandwidth: 18Hz, 35Hz, or 70Hz Programmable damping factor to balance lock time with peaking: 1.2, 2.5, 5, 10, or 20 Multiple phase detectors: phase/frequency, early/late, and multicycle Phase/frequency locking (360 capture) or nearest-edge phase locking (180 capture) Multi-cycle phase detection and locking (up to 8191UI) improves jitter tolerance and lock time APLL frequency options suitable for N x 19.44MHz, N x DS1, N x E1, DS3, E3, 6312kHz, and N x 62.5MHz (for Gigabit Ethernet) 2kHz and 8kHz clocks available on OC1 through OC7 with programmable polarity and pulse width Can operate independently or locked to T0 DPLL Phase detector can be used to measure phase difference between two input clocks
5.3

Input Clock Features
14 input clocks 10 programmable-frequency CMOS/TTL input clocks accept any multiple of 8kHz up to 125MHz Two LVDS/LVPECL/CMOS/TTL input clocks accept any multiple of 8kHz up to 125MHz plus 155.52MHz Two 64kHz composite clock receivers (AMI format) that can also be configured as programmable-frequency CMOS/TTL input clocks if needed All 14 input clocks are constantly monitored by programmable frequency monitors and activity monitors Fast activity monitor can disqualify the selected reference after two missing clock cycles Separate 2/4/8kHz sync input
19-4546; Rev 9; 5/09
12 of 227
DS3100
5.4

Output Clock Features
11 output clocks Five programmable-frequency CMOS/TTL output clocks drive any internally produced clock up 77.76MHz Two programmable-frequency LVDS output clocks drive any internally produced clock up to 311.04MHz Two sync pulses, 2kHz and 8kHz, can be disciplined by a 2kHz or 8kHz sync input One 1.544MHz/2.048MHz output clock One 64kHz composite clock output (AMI format) Output clock rates include 2kHz, 8kHz, NxDS1, NxDS2, DS3, NxE1, E3, 19.44MHz, 38.88MHz, 51.84MHz, 62.5MHz, 77.76MHz, 125.0MHz, 155.52MHz, and 311.04MHz Outputs at even divisors of 311.04MHz have less than 0.5ns peak-to-peak output jitter
5.5

Redundancy Features
Devices on redundant timing cards can be configured for master/slave operation Clocks and frame syncs can be cross-wired between devices to ensure that slave always tracks master Master/slave mode pin can auto-configure slave to track master with no phase build-out and wider bandwidth Input clock priority tables can easily be kept synchronized between master and slave BITS transceivers have high-impedance receive inputs and transmit outputs for redundancy without relays
5.6
5.6.1
BITS Transceiver Features
General
Two independent transceivers with fully independent transmitter and receiver DS1 synchronization interface in SF or ESF format E1 synchronization interface with FAS, CAS, and/or CRC-4 framing J1 support (DS1 with Japanese CRC-6 and RAI) 2048kHz synchronization interface (G.703) 6312kHz Japanese synchronization interface (G.703 Appendix II) Short-haul and long-haul line interface unit Internal software-selectable termination (75, 100, 110, or 120) or external termination High-impedance receive inputs and transmit outputs for relay-less master/slave redundancy Local and remote loopbacks
5.6.2
Receiver
Each receiver can be connected to any of 14 input clocks Automatic receive sensitivity adjustment DS1 receive sensitivity configurable for 0 to -36dB (long haul) or 0 to -15dB (short haul) E1 receive sensitivity configurable for 0 to -43dB (long haul) or 0 to -12dB (short haul) Receive signal level indication in 2.5dB steps from -2.5dB to -34dB (DS1) and -2.5dB to -43dB (E1) Monitor-mode gain settings of 14dB, 20dB, 26dB, and 32dB LOS, OOF, RAI, and AIS status Extraction and validation of SSM messages from DS1 ESF data link or E1 Sa bits Receiver data output pin (RSER) for access to DS1/E1 payload Optional receiver clock and frame sync output pins (RCLK and ROUT) for special applications Receiver power-down control Short-circuit detection
19-4546; Rev 9; 5/09
13 of 227
DS3100
5.6.3
Transmitter
Each transmitter can be connected to any of eight output clocks Transmitter data input pin (TSER) for access to DS1/E1 payload Optional transmitter clock pins (TIN, TCLK, TOUT) for special applications Insertion of SSM messages into DS1 ESF data link or E1 Sa bits Flexible transmit waveform generation DSX-1 line build-outs E1 waveforms include G.703 waveshapes for both 75 coax and 120 twisted pair cables AIS and alternating ones and zeros generation Transmitter power-down control Short-circuit detection/limit Open-circuit detection
5.7

Composite Clock I/O Features
Two composite clock receivers and one composite clock transmitter (all AMI format) Compliant with Telcordia GR-378 composite clock, G.703 centralized clock, and G.703 Appendix II.1 Japanese synchronization interfaces Configurable for 50% or 5/8 duty cycle, 1V or 3V pulse amplitude, and 110/120/133 termination Received signals are monitored for LOS, AMI violations, presence/absence of the 8 kHz component, and presence/absence of the 400Hz component (for G.703 Appendix II.1 option b) Transmitter can generate or suppress the 8kHz component and/or the 400 Hz component (for G.703 Appendix II.1 option b) Composite clock receiver inputs can be configured as programmable-frequency CMOS/TTL inputs if composite clock support is not needed
5.8

General Features
Operates from a single external 12.800MHz local oscillator (TCXO or OCXO) On-chip local oscillator watchdog circuit Microprocessor interface can be 8-bit parallel (Intel or Motorola, multiplexed or nonmultiplexed) or SPI serial Register set can be write-protected
19-4546; Rev 9; 5/09
14 of 227
DS3100
6.
PIN DESCRIPTIONS
Table 6-1. Input Clock Pin Descriptions
PIN H1 P6 A10 P7 B10 C10 A11 B5 A5 B4 A4 B11 C11 A12 B12 A13 C12 B13 A14 B14 NAME(1) REFCLK IC1A IC1 IC2A IC2 IC3 IC4 IC5POS IA, IA IC5NEG IC6POS IA, IA IC6NEG IC7 IC8 IC9 IC10 IC11 IC12 IC13 IC14 SYNC2K IPD IPD IPD IPD IPD IPD IPD IPD IPD TYPE(2) I I IPD I IPD IPD IPD FUNCTION Reference Clock. Connect to a 12.800MHz, high-accuracy, high-stability, low-noise local oscillator (TCXO or OCXO). See Section 7.3. Input Clock 1 AMI. AMI 64kHz composite clock. Enabled when MCR5:IC1SF = 0. See Section 7.11.1, Table 10-6, and Table 10-3. Input Clock 1. CMOS/TTL. Programmable frequency (default 8kHz). Enabled when MCR5:IC1SF = 1. See Section 7.11.1. Input Clock 2 AMI. AMI 64kHz composite clock. Enabled when MCR5:IC2SF = 0. See Section 7.11.1, Table 10-6, and Table 10-3. Input Clock 2. CMOS/TTL. Programmable frequency (default 8kHz). Enabled when MCR5:IC2SF = 1. See Section 7.11.1. Input Clock 3. CMOS/TTL. Programmable frequency (default 8kHz). Input Clock 4. CMOS/TTL. Programmable frequency (default 8kHz). Input Clock 5. LVDS/LVPECL or CMOS/TTL. Programmable frequency (default 19.44MHz LVDS). LVDS: See Table 10-4 and Figure 10-1. LVPECL: See Table 10-5 and Figure 10-2. CMOS/TTL: Bias IC5NEG to 1.4V and connect the single-ended signal to IC5POS. Input Clock 6. LVDS/LVPECL. Programmable frequency (default 19.44MHz LVPECL). LVDS: See Table 10-4 and Figure 10-1. LVPECL: See Table 10-5 and Figure 10-2. CMOS/TTL: Bias IC6NEG to 1.4V and connect the single-ended signal to IC6POS. Input Clock 7. CMOS/TTL. Programmable frequency (default 19.44MHz). Input Clock 8. CMOS/TTL. Programmable frequency (default 19.44MHz). Input Clock 9. CMOS/TTL. Programmable frequency (default 19.44MHz). Input Clock 10. CMOS/TTL. Programmable frequency (default 19.44MHz). Input Clock 11. CMOS/TTL. Programmable frequency (default 19.44MHz in master mode, 6.48MHz in slave mode). Input Clock 12. CMOS/TTL. Programmable frequency (default 1.544/2.048MHz). Input Clock 13. CMOS/TTL. Programmable frequency (default 1.544/2.048MHz). Input Clock 14. CMOS/TTL. Programmable frequency (default 1.544/2.048MHz). Frame Sync Input. 2kHz, 4kHz, or 8kHz.
19-4546; Rev 9; 5/09
15 of 227
DS3100
Table 6-2. Output Clock Pin Descriptions
PIN C6 A7 B7 C7 A8 B3 A3 C2 C1 C8 B8 A9 B9 C9 NAME(1) OC1 OC2 OC3 OC4 OC5 OC6POS OC6NEG OC7POS OC7NEG OC8POS OC8NEG OC9 OC10 OC11 TYPE(2) O3 O3 O3 O3 O3 O3 FUNCTION Output Clock 1. CMOS/TTL. Programmable frequency (default 6.48MHz). Output Clock 2. CMOS/TTL. Programmable frequency (default 38.88MHz). Output Clock 3. CMOS/TTL. Programmable frequency (default 19.44MHz). Output Clock 4. CMOS/TTL. Programmable frequency (default 38.88MHz). Output Clock 5. CMOS/TTL. Programmable frequency (default 77.76MHz). Output Clock 6. LVDS. Programmable frequency (default 38.88MHz LVDS). See Table 10-4 and Figure 10-1. Output Clock 7. LVDS. Programmable frequency (default 19.44MHz LVDS). See Table 10-4 and Figure 10-1. Output Clock 8. AMI. 64kHz composite clock. See Section 7.11.2, Table 10-6, and Table 10-3. Output Clock 9. CMOS/TTL. 1.544/2.048MHz. Output Clock 10. CMOS/TTL. 8kHz frame sync or clock. Output Clock 11. CMOS/TTL. 2kHz multiframe sync or clock.
O3
O3 O3 O3 O3
19-4546; Rev 9; 5/09
16 of 227
DS3100
Table 6-3. BITS Receiver Pin Descriptions
PIN NAME(1) TYPE(2) PIN DESCRIPTION Master Clock for BITS Transceiver 1. In most applications, the device's 204.8MHz master clock (see Section 7.3) is divided by 100 to get the BITS transceiver master clock. For special applications, BCCR3:MCLKS can be set to 1 to source the master clock for BITS transceiver 1 from the MCLK1 pin. The clock applied to MCLK1 can be 1X, 2X, 4X or 8X 2.048MHz for any BITS transceiver mode. For DS1 mode only, MCLK1 can be 1X, 2X, 4X, or 8X 1.544MHz. When BCCR3:MCLKS = 0, the MCLK1 pin is ignored and should be wired high or low. See Section 7.10.1. Master Clock for BITS Transceiver 2. In most applications, the device's 204.8MHz master clock (see Section 7.3) is divided by 100 to get the BITS transceiver master clock. For special applications, BCCR3:MCLKS can be set to 1 to source the master clock for BITS transceiver 2 from the MCLK2 pin. The clock applied to MCLK2 can be 1X, 2X, 4X or 8X 2.048MHz for any BITS transceiver mode. For DS1 mode only, MCLK1 can be 1X, 2X, 4X or 8X 1.544MHz. When BCCR3:MCLKS = 0, the MCLK2 pin is ignored and should be wired high or low. See Section 7.10.1. Receiver Clock Output for BITS Transceiver 1. This pin presents the recovered clock from BITS receiver 1. This output is enabled/disabled by BCCR3:RCEN. When this pin is disabled, the recovered clock can still be forwarded to one of input clocks IC1 to IC14, as specified by BCCR2:RCLKD. When disabled, RCLK1 can function as a general-purpose output whose value is controlled by BCCR3:RCINV. See Section 7.10.2. Receiver Clock Output for BITS Transceiver 2. This pin presents the recovered clock from BITS receiver 2. This output is enabled/disabled by BCCR3:RCEN. When this pin is disabled, the recovered clock can still be forwarded to one of input clocks IC1 to IC14, as specified by BCCR2:RCLKD. When disabled, RCLK2 can function as a general-purpose output whose value is controlled by BCCR3:RCINV. See Section 7.10.2. Receiver Multipurpose Output Pin for BITS Transceiver 1. This output is enabled/disabled by BCCR3:ROEN. Its signal source is specified by BCCR3:ROUTS. Possible sources are the DS1/E1 frame sync and the DS1/E1 multiframe sync. When disabled, ROUT1 can function as a general-purpose output whose value is controlled by BCCR3:ROINV. See Section 7.10.2. Receiver Multipurpose Output Pin for BITS Transceiver 2. This output is enabled/disabled by BCCR3:ROEN. Its signal source is specified by BCCR3:ROUTS. Possible sources are the DS1/E1 frame sync and the DS1/E1 multiframe sync. When disabled, ROUT2 can function as a general-purpose output whose value is controlled by BCCR3:ROINV. See Section 7.10.2. Receiver Serial Data Output for BITS Transceiver 1. When BITS receiver 1 is in DS1 or E1 mode (i.e., when BMCR:RMODE = 0x), this pin presents the received DS1/E1 data stream in NRZ format. RSER1 is updated on the RCLK1 edge specified by BCCR3:RCINV. RSER1 is enabled/disabled by the BCCR3:RSEN control bit. This pin is disabled (low) in other BITS receiver modes. See Sections 7.10.5.1 and 7.10.6.1. Receiver Serial Data Output for BITS Transceiver 2. When BITS receiver 2 is in DS1 or E1 mode (i.e., when BMCR:RMODE = 0x), this pin presents the received DS1/E1 data stream in NRZ format. RSER2 is updated on the RCLK2 edge specified by BCCR3:RCINV. RSER2 is enabled/disabled by the BCCR3:RSEN control bit. This pin is disabled (low) in other BITS receiver modes. See Sections 7.10.5.1 and 7.10.6.1. Differential Receiver Inputs for BITS Transceiver 1. These pins connect to the receive cable through a 1:1 transformer. These pins are high impedance when the receiver is powered down (BLCR4:RPD = 1). See Section 7.10.4 for details. Differential Receiver Inputs for BITS Transceiver 2. These pins connect to the receive cable through a 1:1 transformer. These pins are high impedance when the receiver is powered down (BLCR4:RPD = 1). See Section 7.10.4 for details.
F2
MCLK1
IPD
T10
MCLK2
IPD
K1
RCLK1
O3
R10
RCLK2
O3
K2
ROUT1
O3
P10
ROUT2
O3
J3
RSER1
O3
T11
RSER2
O3
T5 R5 L16 L15
RTIP1 IA RRING1 RTIP2 IA RRING2
19-4546; Rev 9; 5/09
17 of 227
DS3100
Table 6-4. BITS Transmitter Pin Descriptions
PIN L2 T12 NAME(1) TCLK1 TCLK2 TYPE(2) O3 O3 FUNCTION Transmit Clock Output for BITS Transceiver 1. This pin presents the TCLK signal output from the Tx Clock Mux block. This output is enabled/disabled by BCCR4:TCEN. The TSER1 pin is sampled on the TCLK1 edge specified by BCCR4:TCINV. See Section 7.10.3. Transmit Clock Output for BITS Transceiver 2. This pin presents the TCLK signal output from the Tx Clock Mux block. This output is enabled/disabled by BCCR4:TCEN. The TSER2 pin is sampled on the TCLK2 edge specified by BCCR4:TCINV. See Section 7.10.3. Transmit Multipurpose Output Pin for BITS Transceiver 1. This output is enabled/disabled by BCCR4:TOEN. Its signal source is specified by BCCR4:TOUTS. Possible sources are the DS1/E1 frame sync and the DS1/E1 multiframe sync. See Section 7.10.3. Transmit Multipurpose Output Pin for BITS Transceiver 2. This output is enabled/disabled by BCCR4:TOEN. Its signal source is specified by BCCR4:TOUTS. Possible sources are the DS1/E1 frame sync and the DS1/E1 multiframe sync. See Section 7.10.3. Transmitter Multipurpose Input for BITS Transceiver 1. In most applications, the BITS transmitter clock is sourced from one of output clocks OC1-OC7 or OC9, as specified by BCCR1:TCLKS. For special applications, TCLKS can be set to 0000 to the enable the transmitter clock to be sourced from the TIN1 pin. Optionally TIN1 can source the frame or multiframe sync in DS1 and E1 modes. In these latter cases, TIN1 is sampled on the TCLK1 edge specified by BCCR4:TCINV. See Section 7.10.3. Transmitter Multipurpose Input for BITS Transceiver 2. In most applications, the BITS transmitter clock is sourced from one of output clocks OC1-OC7 or OC9, as specified by BCCR1:TCLKS. For special applications, TCLKS can be set to 0000 to the enable the transmitter clock to be sourced from the TIN2 pin. Optionally TIN2 can source the frame or multiframe sync in DS1 and E1 modes. In these latter cases, TIN2 is sampled on the TCLK2 edge specified by BCCR4:TCINV. See Section 7.10.3. Transmitter Serial Data Input for BITS Transceiver 1. When the BITS transmitter is in DS1 or E1 mode (i.e., when BMCR:TMODE = 0x), this pin is the source for the DS1/E1 data stream in NRZ format. TSER1 is sampled on the TCLK1 edge specified by BCCR4:TCINV. Payload bits and optionally some overhead bits are sampled. Normally, this pin is wired high to achieve an all-ones payload. This pin is ignored in other BITS transmitter modes and should be held high or low. See Sections 7.10.5.2 and 7.10.6.2. Transmitter Serial Data Input for BITS Transceiver 2. When the BITS transmitter is in DS1 or E1 mode (i.e., when BMCR:TMODE = 0x), this pin is the source for the DS1/E1 data stream in NRZ format. TSER2 is sampled on the TCLK2 edge specified by BCCR4:TCINV. Payload bits and optionally some overhead bits are sampled. Normally, this pin is wired high to achieve an all-ones payload. This pin is ignored in other BITS transmitter modes and should be held high or low. See Sections 7.10.5.2 and 7.10.6.2. Differential Transmitter Outputs for BITS Transceiver 1. These pins drive the outgoing signal onto the transmit cable through a 1:2 step-up transformer. They can be placed in a high-impedance state by pulling the THZE1 pin high or setting BLCR4:TE = 0 in BITS transceiver 1. These pins are also high impedance when the transmitter is powered down (BLCR4:TPD = 1). The two TTIP1 pins should be externally wired together, and the two TRING1 pins should be externally wired together. See Section 7.10.4. Differential Transmitter Outputs for BITS Transceiver 2. These pins drive the outgoing signal onto the transmit cable through a 1:2 step-up transformer. They can be placed in a high-impedance state by pulling the THZE2 pin high or setting BLCR4:TE = 0 in BITS transceiver 2. These pins are also high impedance when the transmitter is powered down (BLCR4:TPD = 1). The two TTIP2 pins should be externally wired together, and the two TRING2 pins should be externally wired together. See Section 7.10.4. Transmit High-Impedance Enable for BITS Transceiver 1. See Section 7.10.4.2.3. 0 = TTIP1/TRING1 transmit data normally (must also have BLCR4:TE = 1 in BITS transceiver 1) 1 = TTIP1/TRING1 high impedance Transmit High-Impedance Enable for BITS Transceiver 2. See Section 7.10.4.2.3. 0 = TTIP2/TRING2 transmit data normally (must also have BLCR4:TE = 1 in BITS transceiver 2) 1 = TTIP2/TRING2 high impedance
M1
TOUT1
O3
P11
TOUT2
O3
L1
TIN1
IPD
R12
TIN2
IPD
L3
TSER1
IPU
T13
TSER2
IPU
R3, T3 R2, T2 N15, N16 P15, P16 K3
TTIP1 OA TRING1 TTIP2 OA TRING2
THZE1
IPU
T14
THZE2
IPU
19-4546; Rev 9; 5/09
18 of 227
DS3100
Table 6-5. Global Pin Descriptions
PIN B6 NAME(1) RST TYPE(2) IPU FUNCTION Active-Low Reset. When this global asynchronous reset is pulled low, all internal circuitry is reset to default values. The device is held in reset as long as RST is low. RST should be held low for at least two REFCLK cycles. Acitve-Low High-Impedance Enable Input. The JTRST pin must be low to activate this function. 0 = Put all output pins in a high-impedance state 1 = Normal operation Microprocessor Interface Select. During reset, the value on these pins is latched into the IFSEL field of the IFCR register. See Section 7.12. 010 = Intel bus mode (multiplexed) 011 = Intel bus mode (nonmultiplexed) 100 = Motorola mode (nonmultiplexed) 101 = SPI mode (address and data transmitted LSB first) 110 = Motorola mode (multiplexed) 111 = SPI mode (address and data transmitted MSB first) 000, 001 = {unused value} Master/Slave Select Input. Sets the state of the MASTSLV bit in the MCR3 register. 0 = slave mode 1 = master mode Resistor Reference. This pin must be tied to VSS through a 10k 1% resistor. The BITS transceivers use this reference resistor to tune internal termination impedance values. The resistor should be placed as close as possible to the device, and capacitance on the RESREF node must be < 10pF. SONET/SDH Frequency Select Input. Sets the reset-default state of the SONSDH bit in MCR3, the DIG1SS and DIG2SS bits in MCR6, and the OC9SON bit in T4CR1. 0 = SDH rates (N x 2.048MHz) 1 = SONET rates (N x 1.544MHz) Source Switching. Fast source switching control input. See Section 7.6.5. SRFAIL Status. When MCR10:SRFPIN = 1, this pin follows the state of the SRFAIL status bit in the MSR2 register. This gives the system a very fast indication of the failure of the current reference. When MCR10:SRFPIN = 0, SRFAIL is disabled (low). Watchdog Timer. Analog node for the REFCLK watchdog timer. Connect to a resistor (R) to VDDIO and a capacitor (C) to ground. Suggested values are R = 20k and C = 0.01F. See Section 7.3.
R14
HIZ
IPU
N1
IFSEL0 IPD
N2
IFSEL1
P1 R11
IFSEL2 MASTSLV IPU
T7
RESREF
IA
M3
SONSDH
IPD
M2 J2
SRCSW SRFAIL
IPD O3
C5
WDT
IA
19-4546; Rev 9; 5/09
19 of 227
DS3100
Table 6-6. Parallel Interface Pin Descriptions
Note: These pins are active in Intel and Motorola bus modes. See Section 7.12.1 for functional description and Section 10.5 for timing specifications.
PIN
K14
NAME(1)
ALE
TYPE(2)
IPD
FUNCTION
Address Latch Enable. This signal controls the address latch. In nonmultiplexed bus modes, the address is latched from A[8:0]. In these modes, ALE is typically wired high to make the latch transparent. In multiplexed bus modes, the address is latched from A[8] and AD[7:0]. Active-Low Chip Select. This pin must be asserted (low) to read or write internal registers. Active-Low Write Enable or Read/Active-Low Write Select. For Intel bus modes, WR is asserted to write internal registers. For Motorola bus modes, R/W = 1 indicates a read and R/W = 0 indicates a write. Active-Low Read Enable or Active-Low Data Strobe. For the Intel-style interface modes, RD is asserted (low) to read internal registers. For the Motorola-style interface modes, the falling edge of DS enables data output on AD[7:0] during reads while the rising edge of DS latches data from AD[7:0] during writes.
J16 J15
CS WR/R/W
IPU IPU
J14 E16 F15 G14 F16 G15 H14 G16 H15 H16 C14 D14 E14 C15 D15 C16 D16 E15 B15
RD/DS A[8] A[7] A[6] A[5] A[4] A[3] A[2] A[1] A[0] AD[7] AD[6] AD[5] AD[4] AD[3] AD[2] AD[1] AD[0] RDY
IPU
IPD
Address Bus. In nonmultiplexed bus modes, these inputs specify the address of the internal register to be accessed. In multiplexed bus modes, the address is specified on A[8] and AD[7:0], while A[7:0] are not used and should be wired high or low.
I/O
Address/Data Bus. In both multiplexed and nonmultiplexed bus modes, these pins are an 8-bit data bus. In multiplexed bus modes, these pins also convey the lower 8 bits of the register address.
O
Active-Low Ready/Data Acknowledge. This pin is asserted when the device has completed a read or write operation. Interrupt Request. The behavior of this pin is configured in the INTCR register. Polarity can be active high or active low. Drive action can be push-pull or open drain. The pin can also be configured as a general-purpose output if the interrupt request function is not needed.
A15
INTREQ
O
19-4546; Rev 9; 5/09
20 of 227
DS3100
Table 6-7. SPI Bus Mode Pin Descriptions
Note: These pins are active in SPI interface modes. See Section 7.12.2 for functional description and Section 10.6 for timing specifications.
PIN
J16 C16 D16 E15 D14
NAME(1)
CS SCLK SDI SDO CPHA
TYPE(2)
IPU I I O I
FUNCTION
Active-Low Chip Select. This pin must be asserted to read or write internal registers. Serial Clock. SCLK is always driven by the SPI bus master. Serial Data Input. The SPI bus master transmits data to the device on this pin. Serial Data Output. The device transmits data to the SPI bus master on this pin. Clock Phase. See Figure 7-18. 0 = data is latched on the leading edge of the SCLK pulse 1 = data is latched on the trailing edge of the SCLK pulse Clock Polarity. See Figure 7-18. 0 = SCLK is normally low and pulses high during bus transactions 1 = SCLK is normally high and pulses low during bus transactions Interrupt Request. The behavior of this pin is configured in the INTCR register. Polarity can be active high or active low. Drive action can be push-pull or open drain. The pin can also be configured as a general-purpose output if the interrupt request function is not needed.
C14
CPOL
I
A15
INTREQ
O
Table 6-8. JTAG Interface Pin Descriptions
Note: See Section 9 for functional description and Section 10.7 for timing specifications.
PIN
T8 R8 R9 P9 T9
NAME(1)
JTRST JTCLK JTDI JTDO JTMS
TYPE(2)
IPU I IPU O IPU
FUNCTION
Active-Low JTAG Test Reset. Asynchronously resets the test access port (TAP) controller. If not used, JTRST can be held low or high. JTAG Clock. Shifts data into JTDI on the rising edge and out of JTDO on the falling edge. If not used, JTCLK can be held low or high. JTAG Test Data Input. Test instructions and data are clocked in on this pin on the rising edge of JTCLK. If not used, JTDI can be held low or high. JTAG Test Data Output. Test instructions and data are clocked out on this pin on the falling edge of JTCLK. If not used, leave floating. JTAG Test Mode Select. Sampled on the rising edge of JTCLK and is used to place the port into the various defined IEEE 1149.1 states. If not used, connect to VDDIO or leave floating.
Table 6-9. General-Purpose I/O Pin Descriptions
PIN
E2 F3 H2 J1
NAME(1)
GPIO1 GPIO2 GPIO3 GPIO4
TYPE(2)
I/O I/O I/O I/O
FUNCTION
General-Purpose I/O Pin 1. GPCR:GPIO1D configures this pin as an input or an output. GPCR:GPIO1O specifies the output value. GPSR:GPIO1 indicates the state of the pin. General-Purpose I/O Pin 2. GPCR:GPIO2D configures this pin as an input or an output. GPCR:GPIO2O specifies the output value. GPSR:GPIO2 indicates the state of the pin. General-Purpose I/O Pin 3. GPCR:GPIO3D configures this pin as an input or an output. GPCR:GPIO3O specifies the output value. GPSR:GPIO3 indicates the state of the pin. General-Purpose I/O Pin 4. GPCR:GPIO4D configures this pin as an input or an output. GPCR:GPIO4O specifies the output value. GPSR:GPIO4 indicates the state of the pin.
19-4546; Rev 9; 5/09
21 of 227
DS3100
Table 6-10. Power-Supply Pin Descriptions
PIN
D6, D8, D9, D11, E6, E11, F4, F5, F12, F13, H4, H13, J4, J13, L4, L5, L12, L13, M6, M11, N6, N8, N9, N11 B1, B16, D7, D10, E7-E10, G4, G5, G12, G13, H5, H12, J5, J12, K4, K5, K12, K13, M7, M8, M9, M10, N7, N10, R1, R16 A1, A16, D4, D5, D12, D13, E4, E5, E12, E13, F6-F11, G6-G11, H6-H11, J6-J11, K6-K11, L6-L11, M4, M5, M12, M13, N4, N5, N12, N13, T1, T16 A6 C4 B2 A2 C3 D3 T4 P5 M15 M14 R4 P4 M16 N14 D1 D2 E1 E3 F1 G2 G1 G3
NAME(1)
VDD
TYPE(2)
P
FUNCTION
Core Power Supply. 1.8V 10%
VDDIO
P
I/O Power Supply. 3.3V 10%
VSS
P
Ground Reference
VDD_ICDIFF VSS_ICDIFF VDD_OC6 VSS_OC6 VDD_OC7 VSS_OC7 RVDD_P1 RVSS_P1 RVDD_P2 RVSS_P2 TVDD_P1 TVSS_P1 TVDD_P2 TVSS_P2 AVDD_PLL1 AVSS_PLL1 AVDD_PLL2 AVSS_PLL2 AVDD_PLL3 AVSS_PLL3 AVDD_PLL4 AVSS_PLL4
P P P P P P P P P P P P P P P P P P P P P P
Power Supply for LVDS Inputs (IC5 and IC6). 3.3V 10% Return for LVDS Inputs (IC5 and IC6) Power Supply for LVDS Output OC6. 1.8V 10% Return for LVDS Output OC6 Power Supply for LVDS Output OC7. 1.8V 10% Return for LVDS Output OC7 Power Supply for BITS Receiver 1. 3.3V 10% Return for BITS Receiver 1 Power Supply for BITS Receiver 2. 3.3V 10% Return for BITS Receiver 2 Power Supply for BITS Transmitter 1. 3.3V 10% Return for BITS Transmitter 1 Power Supply for BITS Transmitter 2. 3.3V 10% Return for BITS Transmitter 2 Power Supply for T0 Output APLL. 1.8V 10% Return for T0 Output APLL Power Supply for T4 Output APLL. 1.8V 10% Return for T4 Output APLL. Power Supply for T0 Feedback APLL. 1.8V 10% Return for T0 Feedback APLL Power Supply for Master Clock Generator APLL. 1.8V 10% Return for Master Clock Generator APLL
19-4546; Rev 9; 5/09
22 of 227
DS3100 PIN
H3 P8 TM1 TM2 C13, F14, P12 TST_RA1 TST_RB1 TST_RC1 TST_RA2 TST_RB2 TST_RC2 TST_TA1 TST_TB1 TST_TC1 TST_TA2 TST_TB2 TST_TC2
Note 1: Note 2:
NAME(1)
DVDD DVSS R13 T15 N.C. R6 T6 R7 L14 K16 K15 P2 N3 P3 R15 P13 P14
TYPE(2)
P P --
FUNCTION
Power Supply for BITS Transceiver LIU Digital Logic. 3.3V 10% Return for BITS Transceiver LIU Digital Logic Connect to VSS
--
NoConnection
All pin names with an overbar (e.g., CS) are active low. All pins, except power and analog pins, are CMOS/TTL, unless otherwise specified in the pin description. I = input pin O = output pin IA = analog input pin IPD = input pin with internal 50k pulldown IPU = input pin with internal 50k pullup to approx.2.2V I/O = input/output pin OA = analog output pin (can be placed in a high-impedance state) O3 = output pin that can tri-stated (i.e., placed in a high-impedance state) P = power-supply pin
Note 3: Note 4:
All digital pins are I/O pins in JTAG mode. When ramping power supplies up or down, the voltage on any 1.8V power supply pin must not exceed the voltage on any 3.3V powersupply pin.
19-4546; Rev 9; 5/09
23 of 227
DS3100
7.
7.1
FUNCTIONAL DESCRIPTION
Overview
The DS3100 has 14 input clocks, 11 output clocks, two multiprotocol BITS/SSU receivers, and two multiprotocol BITS/SSU transmitters. There are two separate DPLL paths in the device: the high-performance T0 path and the simpler T4 path. See Figure 2-1. Two of the 14 input clocks are 64kHz composite clock receivers (by default), two are LVDS/LVPECL, and 10 are CMOS/TTL (5V tolerant). The composite clock receivers can be converted to CMOS/TTL inputs as needed. The CMOS/TTL inputs can accept signals from 2kHz to 125MHz. The LVDS/LVPECL pins can accept clock signals up to 155.52MHz. The two BITS receivers can receive several synchronization signals including DS1, E1, 2048kHz, and 6312kHz. In DS1 and E1 modes, a built-in framer finds frame sync and extracts the incoming SSM message for inspection by system software. Each of the two BITS receivers can be connected to any one of the 14 inputs clocks. Each input clock can be monitored continually for activity and/or frequency. Frequency can be compared to both a hard limit and a soft limit. Inputs outside the hard limit are declared invalid, while inputs inside the hard limit but outside the soft limit are merely flagged. Each input can be marked unavailable or given a priority number. Separate input priority numbers are maintained for the T0 DPLL and the T4 DPLL. Except in special modes, the highest priority valid input is automatically selected as the reference for each path. Both the T0 and T4 DPLLs can directly lock to many common telecom frequencies, including, but not limited to 8kHz, DS1, E1, 19.44MHz, and 38.88MHz. The DPLLs can also lock to any multiple of 8kHz up to 125MHz. The T0 DPLL is the high-performance path with all the features for node timing synchronization. The T4 DPLL is a simpler auxiliary path typically used to provide derived DS1s, E1s, or other synchronization signals to an external BITS/SSU. The two paths can be operated independently or locked together. Both DPLLs have these features: Automatic reference selection based on input quality and priority Optional manual reference selection/forcing Configurable quality thresholds for each input Adjustable PLL characteristics, including bandwidth, pull-in range, and damping factor Ability to lock to several common telecom frequencies plus multiples of 8kHz up to 155.52MHz Frequency conversion between input and output using digital frequency synthesis Combined performance of a stable, consistent digital PLL and a low-jitter analog output PLL The T0 DPLL has these additional features not available in the T4 DPLL: A full state machine for automatic transitions among free-run, locked, and holdover states Nonrevertive reference switching mode Phase build-out for reference switching ("hitless") and for phase hits on the selected reference Output vs. input phase offset control 18 bandwidth selections from 0.5mHz to 70Hz (vs. three selections for the T4 path) Noise rejection circuitry for low-frequency references Optional software control over holdover frequency Output phase alignment to input frame sync signal Several frequency averaging methods for acquiring the holdover frequency The T4 DPLL has these additional features not available in the T0 DPLL: Optional mode to lock to the T0 DPLL Optional mode to measure the phase difference between two input clocks Ability to generate DS3, E3, 6312kHz, and N x 62.5MHz (Gigabit Ethernet) frequencies
19-4546; Rev 9; 5/09
24 of 227
DS3100 Typically the internal state machine controls the T0 DPLL, but manual control by system software is also available. The T4 DPLL has a simpler state machine that software cannot directly control. In either DPLL, however, software can override the DPLL logic using manual reference selection. The T0 DPLL always operates at 77.76MHz, regardless of the output frequencies selected for the output clock pins. The T4 DPLL can operate at any of several frequencies in order to support generation of frequencies such as 44.736MHz (DS3) and 34.368MHz (E3). When the T4 DPLL is locked to the T0 DPLL, it locks to an 8kHz signal from T0 to ensure synchronization of all possible T4 frequencies, which are always multiples of 8kHz. The outputs of the T0 and T4 DPLLs are connected to high-speed APLLs that multiply the DPLL clock rate and filter DPLL output jitter. The outputs of the APLLs are divided down to make a wide variety of possible frequencies available at the output clock pins. All or some of the output frequencies of the T0 DPLL can be synchronized to an input 2kHz, 4kHz, or 8kHz sync signal (SYNC2K pin). This synchronization to a low-frequency input enables, among other things, two redundant timing cards to maintain output phase alignment with one another. Seven of the output clocks can be configured for a variety of different frequencies from either the T0 DPLL or the T4 DPLL. One output clock is a 64kHz composite clock transmitter (AMI format), one is 1544kHz or 2048kHz, one is 8kHz, and one is 2kHz. Of the seven multifrequency outputs, five are CMOS/TTL and two are LVDS. Altogether more than 60 output frequencies are possible, ranging from 2kHz to 311.04MHz. The two BITS transmitters can transmit DS1, E1, and 2048kHz synchronization signals. In DS1 and E1 modes, a built-in frame formatter frames the signal and inserts the outgoing SSM message. Each of the two BITS transmitters can be connected to any of nine output clocks.
7.2
Device Identification and Protection
The 16-bit read-only ID field in the ID1 and ID2 registers is set to 0C1Ch = 3100 decimal. The device revision can be read from the REV register. Contact the factory to interpret this value and determine the latest revision. The register set can be protected from inadvertent writes using the PROT register.
7.3
Local Oscillator and Master Clock Configuration
The T0 and T4 DPLL paths operate from a 204.8MHz master clock. The master clock is synthesized from a 12.800MHz clock originating from a local oscillator attached to the REFCLK pin. The stability of the T0 DPLL in holdover is equivalent to the stability of the local oscillator. Selection of an appropriate local oscillator is, therefore, of crucial importance if the telecom standards listed in Table 1-1 are to be met. TCXOs can be used in less stringent cases, but OCXOs are required in the most demanding applications. Even OCXOs may need to be shielded to avoid slow frequency changes due to ambient temperature fluctuations and drift. Careful evaluation of the local oscillator component is necessary to ensure proper performance. Contact Maxim at www.maxim-ic.com/support for recommended oscillators. For reference, the Telcordia GR-1244-CORE stability requirements for Stratum 2, Stratum 3E and Stratum 3 are listed in Table 7-1.
Table 7-1. GR-1244 Stratum 2/3E/3 Stability Requirements
PARAMETER Temperature Drift (non-temp) STRATUM 2 n/a 1 x 10-10/day STRATUM 3E 10 x 10-9 1.16 x 10-14/sec ( 1 x 10-9/day) STRATUM 3 280 x 10-9 4.63 x 10-13/sec ( 40 x 10-9/day)
Note: See GR-1244-CORE for additional details.
The stability of the local oscillator is very important, but its absolute frequency accuracy is less important because the DS3100 can compensate for frequency inaccuracies when synthesizing the 204.8MHz master clock from the local oscillator clock. The MCLKFREQ field in registers MCLK1 and MCLK2 specifies the frequency adjustment to be applied. The adjust can be from -771ppm to +514ppm in 0.0196229ppm (i.e., ~0.02ppm) steps.
19-4546; Rev 9; 5/09
25 of 227
DS3100 The DS3100 implements a stand-alone watchdog circuit that causes an interrupt on the INTREQ pin when the local oscillator attached to the REFCLK pin is significantly off frequency. The watchdog interrupt is not maskable, but is subject to the INTCR register settings. When the watchdog circuit activates, reads of any and all registers in the device will return 00h to indicate the failure. In response to the activation of the INTREQ pin or during periodic polling, if system software ever reads 00h from the ID registers (which are hard-coded to 0C1Ch = 3100 decimal) then it can conclude that the local oscillator attached to that DS3100 has failed. For proper operation of the watchdog timer, connect the WDT pin to a resistor (R) to VDDIO and a capacitor (C) to ground. Suggested values are R = 20k and C = 0.01F.
7.4
Input Clock Configuration
The DS3100 has 14 input clocks: IC1 to IC14. Table 7-2 provides summary information about each clock, including signal format and available frequencies. The device tolerates a wide range of duty cycles on input clocks, out to a minimum high time or minimum low time of 3ns or 30% of the clock period, which ever is smaller.
7.4.1
Signal Format Configuration
Inputs with CMOS/TTL signal format accept both TTL and 3.3V CMOS levels. One key configuration bit that affects the available frequencies is the SONSDH bit in MCR3. When SONSDH = 1 (SONET mode), the 1.544MHz frequency is available. When SONSDH = 0 (SDH mode), the 2.048MHz frequency is available. During reset, the default value of this bit is latched from the SONSDH pin. Input clocks IC5 and IC6 can be configured to accept LVDS, LVPECL, or CMOS/TTL signals by using the proper set of external components. The recommended LVDS termination is shown in Figure 10-1, and the LVDS electrical specifications are listed in Table 10-4. The recommended LVPECL termination is shown in Figure 10-2, and the LVPECL electrical specifications are listed in Table 10-5. To configure these differential inputs to accept singleended CMOS/TTL signals, use a voltage-divider to bias the ICxNEG pin to approximately 1.4V and connect the single-ended signal to the ICxPOS pin. If IC5 or IC6 is not used it should be configured for LVDS and left floating (one input is internally pulled high and the other internally pulled low). (See also MCR5:IC5SF and IC6SF.) By default, input clocks IC1 and IC2 are 64kHz composite clock receivers (see Section 7.11). The composite clock signal is a 64kHz AMI clock with an embedded 8kHz clock indicated by deliberate bipolar violations (BPVs) every 8 clock cycles. The 8kHz component is the clock that is forwarded to the DPLLs. The AMI composite clock electrical specifications are shown in Table 10-6, and the recommended external components are shown in Table 10-3. IC1 and IC2 can be configured as standard CMOS/TTL inputs (identical to IC3) by setting MCR5:IC1SF = 1 or MCR5:IC2SF = 1, respectively.
19-4546; Rev 9; 5/09
26 of 227
DS3100
Table 7-2. Input Clock Capabilities
INPUT CLOCK IC1 IC2 IC3 IC4 IC5 IC6 IC7 IC8 IC9 IC10 IC11 IC12 IC13 IC14 SIGNAL FORMATS AMI or CMOS/TTL(3) AMI or CMOS/TTL(3) CMOS/TTL CMOS/TTL LVDS/LVPECL or CMOS/TTL LVDS/LVPECL or CMOS/TTL CMOS/TTL CMOS/TTL CMOS/TTL CMOS/TTL CMOS/TTL CMOS/TTL CMOS/TTL CMOS/TTL FREQUENCIES 64kHz composite clock or up to 125MHz 64kHz composite clock or up to 125MHz Up to 125MHz(1) Up to 125MHz Up to 155.52MHz(2) Up to 155.52MHz Up to 125MHz Up to 125MHz Up to 125MHz Up to 125MHz Up to 125MHz Up to 125MHz Up to 125MHz Up to 125MHz 8kHz 8kHz 8kHz 8kHz 19.44MHz 19.44MHz 19.44MHz 19.44MHz 19.44MHz 19.44MHz Master mode (MASTSLV = 1): 19.44MHz Slave mode (MASTSLV = 0): 6.48MHz SONET mode (SONSDH = 1): 1.544MHz SDH mode (SONSDH = 0): 2.048MHz SONET mode (SONSDH = 1): 1.544MHz SDH mode (SONSDH = 0): 2.048MHz SONET mode (SONSDH = 1): 1.544MHz SDH mode (SONSDH = 0): 2.048MHz DEFAULT FREQUENCY
Note 1: Note 2: Note 3:
Available frequencies for CMOS/TTL input clocks are 2kHz, 4kHz, 8kHz, 1.544MHz (SONET mode), 2.048MHz (SDH mode), 6.312MHz, 6.48MHz, 19.44MHz, 25.92MHz, 38.88MHz, 51.84MHz, 77.76MHz, and N x 8kHz for 2 N 15,625. Available frequencies for LVDS/LVPECL input clocks include all CMOS/TTL frequencies in Note 1 plus 155.52MHz. Signal formats for IC1 and IC2 are controlled by MCR5:IC1SF and IC2SF, respectively.
19-4546; Rev 9; 5/09
27 of 227
DS3100
7.4.2
Frequency Configuration
Input clock frequencies are configured in the FREQ field of the ICR registers. The DIVN and LOCK8K bits of these same registers specify the locking frequency mode, as shown in Table 7-3.
Table 7-3. Locking Frequency Modes
DIVN 0 0 1 7.4.2.1 LOCK8K 0 1 X LOCKING FREQUENCY MODE Direct lock mode LOCK8K mode DIVN mode
Direct Lock Mode
In direct lock mode, the DPLLs lock to the selected reference at the frequency specified in the corresponding ICR register. Direct lock mode can only be used for input clocks with these specific frequencies: 2kHz, 4kHz, 8kHz, 1.544MHz, 2.048MHz, 6.312MHz, 6.48MHz, 19.44MHz, 25.92MHz, 38.88MHz, 51.84MHz, 77.76MHz, and 155.52MHz. For the 155.52MHz case, the input clock is internally divided by two, and the DPLL direct-locks at 77.76 MHz. The T0 DPLL can direct-lock to all the specific input frequencies listed above, and so can the T4 DPLL when configured for 77.76MHz operation (see Section 7.8.2.2). When configured for non-77.76MHz operation, the T4 DPLL can direct-lock to any of the specific frequencies listed above from 2kHz to 6.48MHz, but for the specific frequencies of 19.44MHz and higher, the input must be configured for LOCK8K or DIVN mode. MTIE may be somewhat lower in direct lock mode because the higher frequencies allow more frequent phase updates. 7.4.2.2 LOCK8K Mode
In LOCK8K mode, an internal divider is configured to divide the selected reference down to 8kHz. The DPLLs lock to the 8kHz output of the divider. LOCK8K mode can only be used for input clocks with these frequencies: 8kHz, 1.544MHz, 2.048MHz, 6.312MHz, 6.48MHz, 19.44MHz, 25.92MHz, 38.88MHz, 51.84MHz, 77.76MHz, and 155.52MHz. LOCK8K mode is enabled for a particular input clock by setting the LOCK8K bit in the corresponding ICR register. LOCK8K mode gives a greater tolerance to input jitter because it uses lower frequencies for phase comparisons. The clock edge to lock to on the selected reference can be configured using the 8KPOL bit in the TEST1 register. For 2kHz and 4kHz clocks, the LOCK8K bit is ignored and direct-lock mode is used. 7.4.2.3 DIVN Mode
In DIVN mode, the internal divider is configured from the value stored in the DIVN registers. The DIVN value must be chosen so that when the selected reference is divided by DIVN+1 the output clock is 8kHz. The DPLLs lock to the 8kHz output of the divider. DIVN mode can only be used for input clocks whose frequency is an integer multiple of 8 kHz and less than or equal to 155.52MHz. The DIVN register field can range from 1 to 19,439 inclusive. The same DIVN+1 factor is used for all input clocks configured for DIVN mode. When DIVN = 1 in an ICR register, the FREQ field of that register is ignored. Note that although DIVN divider is able to divide down clock rates has as high as 155.52MHz (DIVN = 19,439), the CMOS/TTL inputs are only rated for a maximum clock rate of 125MHz (DIVN = 15,624).
19-4546; Rev 9; 5/09
28 of 227
DS3100
7.5
Input Clock Quality Monitoring
Each input clock is continuously monitored for frequency accuracy and activity. Frequency monitoring is described in Section 7.5.1, while activity monitoring is described in Sections 7.5.2 and 7.5.3. Any input clock that has a frequency out-of-band alarm or activity alarm is automatically declared invalid. The valid/invalid state of each input clock is reported in the corresponding real-time status bit in register VALSR1 or VALSR2. When the valid/invalid state of a clock changes, the corresponding latched status bit is set in register MSR1 or MSR2, and an interrupt request occurs if the corresponding interrupt enable bit is set in registers IER1 or IER2. Input clocks marked invalid cannot be selected as the reference for either DPLL. If the T4 DPLL does not have any valid input clocks available, the T4NOIN status bit is set to 1 in MSR3.
7.5.1
Frequency Monitoring
The DS3100 monitors the frequency of each input clock and invalidates any clock whose frequency is outside of specified limits. Two frequency limits can be specified: a soft limit and a hard limit. For all input clocks except the T0 DPLL's selected reference, these limits are specified in the ILIMIT register. For the T0 DPLL's selected reference the limits are specified in the SRLIMIT register. When the frequency of an input clock is greater than or equal to the soft limit, the corresponding SOFT alarm bit is set to 1 in the ISR registers. The soft limit is only for monitoring; triggering it does not invalidate the clock. When the frequency of an input clock is greater than or equal to the hard limit, the corresponding HARD alarm bit is set to 1 in the ISR registers, and the clock is marked invalid in the VALSR registers. Monitoring according to the hard and soft limits is enabled/disabled using the HARDEN and SOFTEN bits in the MCR10 register. Both the ILIMIT and SRLIMIT registers have a default soft limit of 11.43ppm and a default hard limit of 15.24ppm. Limits can be set from 3.81ppm to 60.96ppm in 3.81ppm steps. Both the SOFT and HARD alarm limits have hysteresis as required by GR-1244. Frequency monitoring is only done on an input clock when the clock does not have an activity alarm.
6 26
Frequency measurement can be done with respect to the internal 204.8MHz master clock or the 77.76MHz T0 DPLL output, as specified by the FMONCLK bit in MCR10. Measured frequency can be read from any frequency monitor by specifying the input clock in the FMEASIN field of MCR11 and reading the frequency from the FMEAS register.
7.5.2
Activity Monitoring
Each input clock is monitored for activity and proper behavior using a leaky bucket accumulator. A leaky bucket accumulator is similar to an analog integrator: the output amplitude increases in the presence of input events and gradually decays in the absence of events. When events occur infrequently, the accumulator value decays fully between events and no alarm is declared. When events occur close enough together, the accumulator increments faster than it can decay and eventually reaches the alarm threshold. After an alarm has been declared, if events occur infrequently enough, the accumulator can decay faster than it is incremented and eventually reaches the alarm clear threshold. The leaky bucket accumulator for each input clock can be assigned one of four configurations (0 through 3) in the BUCKET field of the ICR registers. Each leaky bucket configuration has programmable size, alarm declare threshold, alarm clear threshold, and decay rate, all of which are specified in the LBxy registers at addresses 50h through 5Fh. Activity monitoring is divided into 128ms intervals. The accumulator is incremented once for each 128ms interval in which the input clock is inactive for more than two cycles (more than four cycles for 155.52MHz input clocks). Thus the "fill" rate of the bucket is at most 1 unit per 128ms, or approximately 8 units/second. During each period of 1, 2, 4 or 8 intervals (programmable), the accumulator decrements if no irregularities occur. Thus the "leak" rate of the bucket is approximately 8, 4, 2, or 1 units/second. A leak is prevented when a fill event occurs in the same interval. When the value of an accumulator reaches the alarm threshold (LBxU register), the corresponding ACT alarm bit is set to 1 in the ISR registers, and the clock is marked invalid in the VALSR registers. When the value of an accumulator reaches the alarm clear threshold (LBxL register), the activity alarm is cleared by clearing the clock's ACT bit. The accumulator cannot increment past the size of the bucket specified in the LBxS register. The decay rate of the accumulator is specified in the LBxD register. The values stored in the leaky bucket configuration registers must have the following relationship at all times: LBxS LBxU > LBxL.
26
19-4546; Rev 9; 5/09
29 of 227
DS3100 When the leaky bucket is empty, the minimum time to declare an activity alarm in seconds is LBxU / 8 (where the "x" in "LbxU" is the leaky bucket configuration number, 0 to 3). The minimum time to clear an activity alarm in seconds is [2LBxD x (LBxS - LBxL) / 8]. For example, assume LBxU = 8, LBxL = 1, LBxS = 10, and LBxD = 0. The minimum time to declare an activity alarm would be 8 / 8 = 1 second. The minimum time to clear the activity alarm would be [20 x (10 - 1) / 8 = 1.125 seconds]. For an input clock that is connected to a BITS receiver, if BCCR5:BPV = 1 then the accumulator is also incremented whenever a BPV is detected in the incoming signal. See Section 7.10.2 for details. For input clocks IC1 and IC2 configured in composite clock mode, if MCR5:BITERR = 1, then the accumulator is also incremented whenever a violation of the one-BPV-in-eight pattern is detected.
7.5.3
Selected Reference Activity Monitoring
The input clock that each DPLL is currently locked to is called the selected reference. The quality of a DPLL's selected reference is exceedingly important, since missing cycles and other anomalies on the selected reference can cause unwanted jitter, wander or frequency offset on the output clocks. When anomalies occur on the selected reference they must be detected as soon as possible to give the DPLL opportunity to temporarily disconnect from the reference until the reference is available again. By design, the regular input clock activity monitor (Section 7.5.2) is too slow to be suitable for monitoring the selected reference. Instead, each DPLL has its own fast activity monitor that detects inactivity within approximately two missing reference clock cycles (within approximately four missing cycles for 155.52MHz references). When the T0 DPLL detects a no-activity event, it immediately enters mini-holdover mode to isolate itself from the selected reference and sets the SRFAIL bit in MSR2. The setting of the SRFAIL bit can cause an interrupt request on the INTREQ pin if the corresponding enable bit is set in IER2. If MCR10:SRFPIN = 1, the SRFAIL output pin follows the state of the SRFAIL status bit. Optionally, a no-activity event can also cause an ultra-fast reference switch (see Section 7.6.4). When PHLIM1:NALOL = 0 (default), the T0 DPLL does not declare loss-of-lock during no-activity events. If the selected reference becomes available again before any alarms are declared by the activity monitor or frequency monitor, then the T0 DPLL continues to track the selected reference using nearest-edge locking (180) to avoid cycle slips. When NALOL = 1, the T0 DPLL declares loss-of-lock during no-activity events. This causes the T0 state machine to transition to the loss-of-lock state, which sets the MSR2:STATE bit and causes an interrupt request if enabled. If the selected reference becomes available again before any alarms are declared by the activity monitor or frequency monitor, then the T0 DPLL tracks the selected reference using phase/frequency locking (360) until phase lock is reestablished. When the T4 DPLL detects a no-activity event, its behavior is similar to the T0 DPLL with respect to the PHLIM1:NALOL control bit. Unlike the T0 DPLL, however, the T4 DPLL does not set the SRFAIL status bit. If NALOL = 1, the T4 DPLL clears the OPSTATE:T4LOCK status bit, which sets MSR3:T4LOCK and causes an interrupt request if enabled.
7.5.4
Composite Clock Inputs
When input clocks IC1 and IC2 are configured for composite clock mode (MCR5:IC1SF = 0 and MCR5:IC2SF = 0), they are also monitored for various defects (AMI error, LOS, etc.) See Section 7.11.1 for further details.
19-4546; Rev 9; 5/09
30 of 227
DS3100
7.6
7.6.1
Input Clock Priority, Selection, and Switching
Priority Configuration
During normal operation, the selected reference for the T0 DPLL and the selected reference for the T4 DPLL are chosen automatically based on the priority rankings assigned to the input clocks in the input priority registers (IPR1 to IPR7). Each of these seven registers has priority fields for two input clocks. When T4T0 = 0 in the MCR11 register, the IPR registers specify the input clock priorities for the T0 DPLL. When T4T0 = 1, the IPR registers specify the input clock priorities for the T4 DPLL. The default input clock priorities, for both PLLs, are shown in Table 7-4. Any unused input clock should be given the priority value 0, which disables the clock and marks it as unavailable for selection. Priority 1 is highest while priority 15 is lowest. The same priority can be given to two or more clocks.
Table 7-4. Default Input Clock Priorities
INPUT CLOCK IC1 IC2 IC3 IC4 IC5 IC6 IC7
Note 1:
DEFAULT PRIORITY 2 3 4 5 6 7 8
INPUT CLOCK IC8 IC9 IC10 IC11 IC12 IC13 IC14
DEFAULT PRIORITY 9 10 11 12 or 1 (1) 13 14 15
During reset, the default priority for IC11 is set to 12 in the master device and set to 1 in the slave device. Devices are configured as master and slave by the value of the MASTSLV pin. (The state of the MASTSLV pin is mirrored in the MASTSLV bit of the MCR3 register.) See Section 7.9.
7.6.2
Automatic Selection Algorithm
The real-time valid/invalid state of each input clock is maintained in the VALSR1 and VALSR2 registers. The selected reference can be marked invalid for phase, frequency or activity. Other input clocks can be invalidated for frequency or activity. The reference selection algorithm for each DPLL chooses the highest-priority valid input clock to be the selected reference. To select the proper input clock based on these criteria, the selection algorithm maintains a priority table of valid inputs. The top three entries in this table and the selected reference are displayed in the PTAB1 and PTAB2 registers. When T4T0 = 0 in the MCR11 register, these registers indicate the highest priority input clocks for the T0 DPLL. When T4T0 = 1, they indicate the highest priority input clocks for the T4 path. If two or more input clocks are given the same priority number then those inputs are prioritized among themselves using a fixed circular list. If one equal-priority clock is the selected reference but becomes invalid then the next equal-priority clock in the list becomes the selected reference. If an equal-priority clock that is not the selected reference becomes invalid, it is simply skipped over in the circular list. The selection among equal-priority inputs is inherently nonrevertive, and revertive switching mode (see next paragraph) has no effect in the case where multiple equal-priority inputs have the highest priority. An important input to the selection algorithm for T0 DPLL is the REVERT bit in the MCR3 register. In revertive mode (REVERT = 1), if an input clock with a higher priority than the selected reference becomes valid, the higherpriority reference immediately becomes the selected reference. In nonrevertive mode (REVERT = 0), the higherpriority reference does not immediately become the selected reference but does become the highest-priority reference in the priority table (REF1 field in the PTAB1 register). (The selection algorithm always switches to the highest-priority valid input when the selected reference goes invalid, regardless of the state of the REVERT bit.) For many applications, nonrevertive mode is preferred for the T0 DPLL because it minimizes disturbances on the output clocks due to reference switching. The T4 DPLL always operates in revertive mode. In nonrevertive mode, planned switchover to a newly valid higher priority input clock can be done manually under software control. The validation of the new higher priority clock sets the corresponding status bit in the MSR1 or 19-4546; Rev 9; 5/09 31 of 227
DS3100 MSR2 register, which can drive an interrupt request on the INTREQ pin if needed. System software can then respond to this change of state by briefly enabling revertive mode (toggling REVERT high then back low) to drive the switchover to the higher priority clock. In most systems redundant timing cards are required, with one functioning as the master and the other as the slave. In such systems the priority tables of the master and slave must match. The DS3100's register set makes it easy for the slave's priority table to track the master's table. At system start-up, the same priorities must be assigned to the input clocks, for both DPLLs, in the master and slave devices. During operation, if an input clock becomes valid or invalid in one device (master or slave), the change is flagged in that device's MSR1 or MSR2 register, which can drive an interrupt request on the INTREQ pin if needed. The real-time valid/invalid state of the input clocks can then be read from that device's VALSR1 and VALSR2 registers. Once the nature of the state change is understood, the control bits of the other device's VALCR1 and VALCR2 registers can be manipulated to mark clocks invalid in the other device as well.
7.6.3
Forced Selection
The T0FORCE field in the MCR2 register and the T4FORCE field in the MCR4 register provide a way to force a specified input clock to be the selected reference for the T0 and T4 DPLLs, respectively. In both T0FORCE and T4FORCE, values of 0 and 15 specify normal operation with automatic reference selection. Values from 1 to 14 specify the input clock to be the forced selection. Internally forcing is accomplished by giving the specified clock the highest priority (as specified in PTAB1:REF1). In revertive mode (MCR3:REVERT = 1) the forced clock automatically becomes the selected reference (as specified in PTAB1:SELREF) as well. In nonrevertive mode (T0 DPLL only) the forced clock only becomes the selected reference when the existing selected reference is invalidated or made unavailable for selection. In both revertive and nonrevertive modes when an input is forced to be the highest priority, the normal highest priority input (when no input is forced) is listed as the second-highest priority (PTAB2:REF2) and the normal second-highest priority input is listed as the third-highest priority (PTAB2:REF3).
7.6.4
Ultra-Fast Reference Switching
By default, disqualification of the selected reference and switchover to another reference occurs when the activity monitor's inactivity alarm threshold has been crossed, a process that takes on the order of hundreds of milliseconds or seconds. For the T0 DPLL, an option for extremely fast disqualification and switchover is also available. When ultra-fast switching is enabled (MCR10:UFSW = 1), if the fast activity monitor detects approximately two missing clock cycles it declares the reference failed by forcing the leaky bucket accumulator to its upper threshold (see Section 7.5.2) and initiates reference switching. This is in addition to setting the SRFAIL bit in MSR2 and optionally generating an interrupt request, as described in Section 7.5.3. When ultra-fast switching occurs, the T0 DPLL transitions to the prelocked 2 state, which allows switching to occur faster by bypassing the Loss-of-Lock state. The device should be in non-revertive mode when ultra-fast switching is enabled. If the device is in revertive mode, ultra-fast switching could cause excessive reference switching when the highest priority input is intermittent.
7.6.5
External Reference Switching Mode
In the external reference switching mode, the SRCSW input pin controls reference switching between two clock inputs. This mode is enabled by setting the EXTSW bit to 1 in the MCR10 register. In this mode, if the SRCSW pin is high, the device is forced to lock to input IC3 (if the priority of IC3 is nonzero in IPR2) or IC5 (if the priority of IC3 is zero) whether or not the selected input has a valid reference signal. If the SRCSW pin is low the device is forced to lock to input IC4 (if the priority of IC4 is non-zero in IPR2) or IC6 (if the priority of IC4 is zero) whether or not the selected input has a valid reference signal. During reset the default value of the EXTSW bit is latched from the SRCSW pin. If external reference switching mode is enabled during reset, the default frequency tolerance (DLIMIT registers) is configured to 80ppm rather than the normal default of 9.2ppm. In external reference switching mode the device is simply a clock switch, and the DPLL is forced to lock onto the selected reference whether it is valid or not. Unlike forced reference selection (Section 7.6.3) this mode controls the PTAB1:SELREF field directly and is therefore not affected by the state of the MCR3:REVERT bit. During external reference switching mode, only PTAB1:SELREF is affected; the REF1, REF2 and REF3 fields in the PTAB registers continue to indicate the highest, second-highest, and third-highest priority valid inputs chosen by the automatic selection logic. External reference switching mode only affects the T0 DPLL.
19-4546; Rev 9; 5/09
32 of 227
DS3100
7.6.6
Output Clock Phase Continuity During Reference Switching
If phase build out is enabled (PBOEN = 1 in MCR10) or the DPLL frequency limit (DLIMIT) is set to less than 30ppm then the device always complies with the GR-1244-CORE requirement that the rate of phase change must be less than 81ns per 1.326ms during reference switching.
7.7
DPLL Architecture and Configuration
Both the T0 and T4 paths of the device are digital PLLs (DPLLs) with analog PLLs (APLLs) at the output stage. This architecture combines the benefits of both PLL types. Digital PLLs have two key benefits: (1) stable, repeatable performance that is insensitive to process variations, temperature and voltage, and (2) flexible behavior that is easily programmed via configuration registers. DPLLs use digital frequency synthesis (DFS) to generate various clocks. In DFS, a high-speed master clock (204.8MHz) is multiplied up from the 12.800MHz local oscillator clock applied to the REFCLK pin. This master clock is then digitally divided down to the desired output frequency. Since the resolution of the DFS process is one master clock cycle or 4.88ns, the DFS output clock has jitter of up to 1 master clock UI (4.88ns) pk-pk. The analog PLLs filter the jitter from the DPLLs, reducing the 4.88ns pk-pk jitter to 0.5ns pk-pk and 60ps RMS, typical, measured broadband (10Hz to 1GHz). The DPLLs in the device are configurable for many PLL parameters including bandwidth, damping factor, input frequency, pull-in/hold-in range, loop frequency, output frequency, input-to-output phase offset, phase build-out, and more. No knowledge of loop equations or gain parameters is required to configure and operate the device. No external components are required for the DPLLs or the APLLs except the high-quality local oscillator connected to the REFCLK pin. The T0 path is the main path through the device, and the T0 DPLL has a full free-run/locked/holdover state machine and full programmability. The T4 path is a simpler frequency converter/synthesis path, lacking the low bandwidth settings, phase build-out, phase adjustment controls, and holdover state found in the T0 DPLL.
7.7.1
T0 DPLL State Machine
The T0 DPLL has three main timing modes: locked, holdover, and free-run. The control state machine for the T0 DPLL has states for each timing mode as well as three temporary states: prelocked, prelocked 2, and loss-of-lock. The state transition diagram is shown in Figure 7-1. Descriptions of each state are given in the paragraphs below. During normal operation the state machine controls state transitions. When necessary, however, the state can be forced using the T0STATE field of the MCR1 register. Whenever the T0 DPLL changes state, the STATE bit in MSR2 is set, which can cause an interrupt request if enabled. The current T0 DPLL state can be read from the T0STATE field of the OPSTATE register. 7.7.1.1 Free-Run State Free-run mode is the reset default state. In free-run, all output clocks are derived from the 12.800MHz local oscillator attached to the REFCLK pin. The frequency of each output clock is a specific multiple of the local oscillator. The frequency accuracy of each output clock is equal to the frequency accuracy of the master clock (see Section 7.3). The state machine transitions from free-run to the prelocked state when at least one input clock is valid. 7.7.1.2 Prelocked State The prelocked state provides a 100-second period (default value of PHLKTO register) for the DPLL to lock to the selected reference. If phase lock is achieved during this period then the state machine transitions to locked mode. If the DPLL fails to lock to the selected reference within the phase-lock time-out period specified by PHLKTO then a phase lock alarm is raised (corresponding LOCK bit set in the ISR register), invalidating the input (ICn bit goes low in VALSR registers). If another input clock is valid then the state machine re-enters the prelocked state and tries to lock to the alternate input clock. If no other input clocks are valid then the state machine transitions back to the free-run state. In revertive mode (REVERT = 1 in MCR3), if a higher priority input clock becomes valid during the phase-lock timeout period, then the state machine re-enters the prelocked state and tries to lock the higher priority input. If a 19-4546; Rev 9; 5/09 33 of 227
DS3100 phase-lock timeout period longer than 100 seconds is required for locking (such as 700 seconds for Stratum 3E or 1000 seconds for Stratum 2 applications), the PHLKTO register must be configured accordingly.
Figure 7-1. T0 DPLL State Transition Diagram
Reset (selected reference invalid OR out of lock >100s) AND no valid input clock [selected reference invalid OR out of lock >100s OR (revertive mode AND valid higher-priority input)] AND valid input clock available [selected reference invalid OR (revertive mode AND valid higher-priority input)] AND valid input clock available phase-locked to selected reference
Free-Run select ref (001) all input clocks evaluated at least one input valid
Pre-locked wait for <=100s (110) phase-locked to selected reference
Locked (100) phase-lock regained on selected reference within 100s loss-of-lock on selected reference
selected reference invalid AND no valid input clock available
[selected reference invalid OR (selected reference invalid OR (revertive mode AND valid higher-priority input) out of lock >100s) AND OR out of lock >100s] AND Pre-locked 2 Loss-of-Lock no valid input clock available valid input clock available wait for <=100s wait for <=100s (101) (111) (selected reference invalid OR out of lock >100s) AND no valid input clock available all input clocks evaluated at least one input valid
Holdover select ref (010)
[selected reference invalid OR out of lock >100s OR (revertive mode AND valid higher-priority input)] AND valid input clock available
Note 1: Note 2: Note 3: Note 4: Note 5:
An input clock is valid when it has no activity alarm, no hard frequency limit alarm, and no phase lock alarm (see the VALSR registers and the ISR registers). All input clocks are continuously monitored for activity and frequency. Only the selected reference is monitored for loss of lock. Phase lock is declared internally when the DPLL has maintained phase lock continuously for approximately 1 to 2 seconds. To simply the diagram, the phase-lock timeout period is always shown as 100s, which is the default value of the PHLKTO register. Longer or shorter timeout periods can be specified as needed by writing the appropriate value to the PHLKTO register.
19-4546; Rev 9; 5/09
34 of 227
DS3100 7.7.1.3 Locked State
The T0 DPLL state machine can reach the locked state from the prelocked, prelocked 2, or loss-of-lock states when the DPLL has locked to the selected reference for at least one second (see Section 7.7.6). In the locked state, the output clocks track the phase and frequency of the selected reference. While in the locked state, if the selected reference is so impaired that an activity alarm or a hard frequency limit alarm is raised (corresponding ACT or HARD bit set in the ISR register), then the selected reference is invalidated (ICn bit goes low in VALSR registers), and the state machine immediately transitions to either the prelocked 2 state (if another valid input clock is available) or the holdover state (if no other input clock is valid). If loss-of-lock is declared while in the locked state, the state machine transitions to the loss-of-lock state. 7.7.1.4 Loss-of-Lock State When the loss-of-lock detectors (see Section 7.7.6) indicate loss-of-phase lock, the state machine immediately transitions from the locked state to the loss-of-lock state. In the loss-of-lock state the DPLL tries for 100 seconds (default value of PHLKTO register) to regain phase lock. If phase lock is regained during that period, the state machine transitions back to the locked state. If, during the phase-lock timeout period specified by PHLKTO, the selected reference is so impaired that an activity alarm or a hard frequency limit alarm is raised (corresponding ACT or HARD bit set in the ISR registers), then the selected reference is invalidated (ICn bit goes low in VALSR registers), and the state machine immediately transitions to either the prelocked 2 state (if another valid input clock is available) or the holdover state (if no other input clock is valid). If phase lock cannot be regained by the end of the phase-lock timeout period, then a phase lock alarm is raised (corresponding LOCK bit set in the ISR registers), the selected reference is invalidated (ICn bit goes low in VALSR registers), and the state machine transitions to either the prelocked 2 state (if another valid input clock is available) or the holdover state (if no other input clock is valid). 7.7.1.5 Prelocked 2 State The prelocked and prelocked 2 states are similar. The prelocked 2 state provides a 100-second period (default value of PHLKTO register) for the DPLL to lock to the new selected reference. If phase lock is achieved during this period, then the state machine transitions to locked mode. If the DPLL fails to lock to the new selected reference within the phase-lock timeout period specified by PHLKTO, then a phase lock alarm is raised (corresponding LOCK bit set in the ISR registers), invalidating the input (ICn bit goes low in VALSR registers). If another input clock is valid, the state machine re-enters the prelocked 2 state and tries to lock to the alternate input clock. If no other input clocks are valid, the state machine transitions to the holdover state. In revertive mode (REVERT = 1 in MCR3), if a higher priority input clock becomes valid during the phase-lock timeout period, the state machine re-enters the prelocked 2 state and tries to lock to the higher priority input. If a phase-lock timeout period longer than 100 seconds is required for locking (such as 700 seconds for Stratum 3E or 1000 seconds for Stratum 2 applications), then the PHLKTO register must be configured accordingly. 7.7.1.6 Holdover State The device reaches the holdover state when it declares its selected reference invalid and has no other valid input clocks available. During holdover the T0 DPLL is not phase locked to any input clock but instead generates its output frequency from stored frequency information, typically the averaged frequency of the DPLL when it was in the locked state. The device can be configured for manual or automatic holdover as described in the following subsections. When at least one input clock has been declared valid the state machine immediately transitions from holdover to the prelocked 2 state and tries to lock to the highest priority valid clock. 7.7.1.6.1 Automatic Holdover
For automatic holdover (MANHO = 0 in MCR3), the device can be further configured for instantaneous mode or averaged mode. In instantaneous mode (AVG = 0 in HOCR3), the holdover frequency is set to the DPLL's current frequency at the moment of entry into holdover (i.e., the value of the FREQ field in the FREQ1, FREQ2 and FREQ3 registers when MCR11:T4T0 = 0). The FREQ field is the DPLL's integral path and therefore is an average 19-4546; Rev 9; 5/09 35 of 227
DS3100 frequency with a rate of change inversely proportional to the DPLL bandwidth. The DPLL's proportional path is not used to minimize the effect of recent phase disturbances on the holdover frequency. In averaged mode (AVG = 1 in HOCR3), the holdover frequency is set to an internally averaged value. During locked operation the frequency indicated in the FREQ field is internally averaged. The FAST bit in HOCR3 determines the period of this averaging. When FAST=1 the frequency is averaged for a period of approximately 8 minutes. When FAST = 0 (slow), the frequency is averaged for a period of approximately 110 minutes. The T0 DPLL indicates that it has acquired valid holdover values by setting the FHORDY and SHORDY status bits in VALSR2 (real-time status) and MSR4 (latched status). If FAST = 0 and the T0 DPLL must enter holdover before the 110-minute average is available, then the 8-minute average is used, if available. Otherwise the instantaneous value from the integral path is used. If FAST = 1 and the T0 DPLL must enter holdover before the 8-minute average is available, then the instantaneous value is used. 7.7.1.6.2 Manual Holdover For manual holdover (MANHO = 1 in MCR3), the holdover frequency is set by the HOFREQ field in the HOCR1, HOCR2 and HOCR3 registers. The HOFREQ field has the same size and format as the current frequency field (FREQ[18:0] in the FREQ1, FREQ2, and FREQ3 registers). If desired, software can, during locked operation, read the current frequency from FREQ, filter or average it over time, and then write the resulting holdover frequency to HOFREQ. The FREQ field is derived from the DPLL's integral path, and thus can be considered an average frequency with a rate of change inversely proportional to the DPLL bandwidth. To combine internal averaging with additional software filtering, the HOFREQ field can be configured to read out the internally averaged frequency when RDAVG = 1 in the HOCR3 register. This averaged value can be read from HOFREQ regardless of the current holdover mode. The FAST bit in HOCR3 specifies whether the value read is from the fast averager or the slow averager. 7.7.1.7 Mini-Holdover When the selected reference fails, the fast activity monitor (Section 7.5.3) isolates the T0 DPLL from the reference within one or two clock cycles to avoid adverse effects on the DPLL frequency. When this fast isolation occurs, the DPLL enters mini-holdover mode, with a mini-holdover frequency as specified by the MINIHO field of HOCR3. Miniholdover lasts until the selected reference returns or a new input clock has been chosen as the selected reference or the state machine enters the holdover state. Note that when the T0 DPLL is configured for manual holdover (MCR3:MANHO=1), mini-holdover is also configured for manual holdover and HOCR3:MINIHO is ignored.
7.7.2
T4 DPLL State Machine
The T4 DPLL has a simpler state machine than the T0 DPLL, as shown in Figure 7-2. The T4 DPLL states are similar to the equivalent states of the T0 DPLL. Note that the T4 DPLL only operates in revertive switching mode.
19-4546; Rev 9; 5/09
36 of 227
DS3100
Figure 7-2. T4 DPLL State Transition Diagram
Reset
Free-Run
all input clocks evaluated at least one input valid selected reference invalid AND no valid input clock available
selected reference invalid AND valid input clock available loss-of-lock on selected reference selected reference invalid AND valid input clock available
Pre-locked
phase-locked to selected reference selected reference invalid AND no valid input clock available
Locked
7.7.3
Bandwidth
The bandwidth of the T4 DPLL is configured in the T4BW register to be 18Hz, 35Hz, or 70Hz. This bandwidth value is used for both acquisition and locked mode. The bandwidth of the T0 DPLL is configured in the T0ABW and T0LBW registers for various values from 0.5mHz to 70Hz. The AUTOBW bit in the MCR9 register controls automatic bandwidth selection. When AUTOBW = 1, the T0 DPLL uses the T0ABW bandwidth during acquisition (not phase locked) and the T0LBW bandwidth when phase locked. When AUTOBW = 0 the T0 DPLL uses the T0LBW bandwidth all the time, both during acquisition and when phase locked. When LIMINT = 1 in the MCR9 register, the DPLL's integral path is limited (i.e., frozen) when the DPLL reaches minimum or maximum frequency. Setting LIMINT = 1 minimizes overshoot when the DPLL is pulling in.
19-4546; Rev 9; 5/09
37 of 227
DS3100
7.7.4
Damping Factor
The damping factor for the T0 DPLL is configured in the DAMP field of the T0CR2 register, while the damping factor the T4 DPLL is configured in the DAMP field of the T4CR2 register. The reset default damping factors for both DPLLs are chosen to give a maximum wander gain peak of approximately 0.1dB. Available settings are a function of DPLL bandwidth (configured in the T4BW, T0ABW, and T0LBW registers). See Table 7-5.
Table 7-5. Damping Factors and Peak Jitter/Wander Gain
BANDWIDTH 0.5mHz to 4Hz 8Hz 18 Hz DAMP[2:0] VALUE 1, 2, 3, 4, 5 1 2, 3, 4, 5 1 2 3, 4, 5 1 2 3 4, 5 1 2 3 4 5 DAMPING FACTOR 5 2.5 5 1.2 2.5 5 1.2 2.5 5 10 1.2 2.5 5 10 20 GAIN PEAK (dB) 0.1 0.2 0.1 0.4 0.2 0.1 0.4 0.2 0.1 0.06 0.4 0.2 0.1 0.06 0.03
35 Hz
70 Hz
7.7.5
Phase Detectors
Phase detectors are used to compare a PLL's feedback clock with its input clock. Several phase detectors are available in both the T0 and T4 DPLLs: Phase/frequency detector (PFD) Early/late phase detector (PD2) for fine resolution Multicycle phase detector (MCPD) for large input jitter tolerance These detectors can be used in combination to give fine phase resolution combined with large jitter tolerance. As with the rest of the DPLL logic, the phase detectors operate at input frequencies up to 77.76MHz. The multicycle phase detector detects and remembers phase differences of many cycles (up to 8191UI). The phase detectors can be configured for normal phase/frequency locking (360 capture) or nearest-edge phase locking (180 capture). With nearest-edge detection the phase detectors are immune to occasional missing clock cycles. The DPLL automatically switches to nearest-edge locking when the multi-cycle phase detector is disabled and the other phase detectors determine that phase lock has been achieved. Setting D180 = 1 in the TEST1 register disables nearest-edge locking and forces the DPLL to use phase/frequency locking. The early/late phase detector, also known as phase detector 2, is enabled and configured in the PD2* fields of registers T0CR2 and T0CR3 for the T0 DPLL and registers T4CR2 and T4CR3 for the T4 DPLL. The reset default settings of these registers are appropriate for all operating modes. Adjustments only affect small signal overshoot and bandwidth. The multicycle phase detector is enabled by setting MCPDEN=1 in the PHLIM2 register. The range of the MCPD-- from 1UI up to 8191UI--is configured in the COARSELIM field of PHLIM2. The MCPD tracks phase position over many clock cycles, giving high jitter tolerance. Thus the use of the MCPD is an alternative to the use of LOCK8K mode for jitter tolerance. When USEMCPD = 1 in PHLIM2, the MCPD is used in the DPLL loop, giving faster pull-in but more overshoot. In this mode the loop has similar behavior to LOCK8K mode. In both cases large phase differences contribute to the dynamics of the loop. When enabled by MCPDEN = 1, the MCPD tracks the phase position whether or not it is used in the DPLL loop. 19-4546; Rev 9; 5/09 38 of 227
DS3100
7.7.6
Loss of Phase Lock Detection
Loss of phase lock is triggered by any of the following in both the T0 and T4 DPLLs: The fine phase lock detector (measures phase between input and feedback clocks) The coarse phase lock detector (measures whole cycle slips) Hard frequency limit detector Inactivity detector The fine phase lock detector is enabled by setting FLEN = 1 in the PHLIM1 register. The fine phase limit is configured in the FINELIM field of PHLIM1. The coarse phase lock detector is enabled by setting CLEN = 1 in the PHLIM2 register. The coarse phase limit is configured in the COARSELIM field of PHLIM2. This coarse phase lock detector is part of the multi-cycle phase detector (MCPD) described in Section 7.7.5. the COARSELIM fields sets both the MCPD range and the coarse phase limit, since the two are equivalent. If loss of phase lock should not be declared for multiple-UI input jitter then the fine phase lock detector should be disabled and the coarse phase lock detector should be used instead. The hard frequency limit detector is enabled by setting FLLOL = 1 in the DLIMIT3 register. The hard limit for the T0 DPLL is configured in registers DLIMIT1 and DLIMIT2. The T4 DPLL hard limit is fixed at 80ppm. When the DPLL frequency reaches the hard limit, loss-of-lock is declared. The DLIMIT3 register also has the SOFTLIM field to specify a soft frequency limit. Exceeding the soft frequency limit does not cause loss-of-lock to be declared. When the T0 DPLL frequency exceeds the soft limit the T0SOFT status bit is set in the OPSTATE register. When the T4 DPLL frequency exceeds the soft limit the T4SOFT status bit is set in OPSTATE. Both the SOFT and HARD alarm limits have hysteresis as required by GR-1244. The inactivity detector is enabled by setting NALOL = 1 in the PHLIM1 register. When this detector is enabled the DPLL declares loss-of-lock after one or two missing clock cycles on the selected reference. See Section 7.5.3. When the T0 DPLL declares loss of phase lock, the state machine immediately transitions to the loss-of-lock state, which sets the STATE bit in the MSR2 register and requests an interrupt if enabled. When the T4 DPLL declares loss of phase lock, the T4LOCK bit is cleared in the OPSTATE register, which sets the T4LOCK bit in the MSR3 register and requests an interrupt if enabled.
19-4546; Rev 9; 5/09
39 of 227
DS3100
7.7.7
7.7.7.1
Phase Monitor and Phase Build-Out
Phase Monitor
The T0 DPLL has a phase monitor that measures the phase error between the input clock reference and the DPLL output. The phase monitor is enabled by setting PHMON:PMEN = 1. When the T0 DPLL is set for low bandwidth, a phase transient on the input causes an immediate phase error that is gradually reduced as the DPLL tracks the input. When the measured phase error exceeds the limit set in the PHMON:PMLIM field, the phase monitor declares a phase monitor alarm by setting the MSR3:PHMON bit. The PMLIM field can be configured for a limit ranging from about 1s to about 3.5s. 7.7.7.2 Phase Build-Out in Response to Input Phase Transients See Telcordia GR-1244-CORE Section 5.7 for an explanation of phase build-out (PBO) and the requirement for Stratum 2 and 3E clocks to perform PBO in response to input phase transients. When the phase monitor is enabled (as described in Section 7.7.7.1) and PHMON:PMPBEN = 1, the T0 DPLL automatically triggers PBO events in response to input transients greater than the limit set in PHMON:PMLIM. The range of limits available in the PMLIM field allows the T0 DPLL to be configured to build out input transients greater than 3.5s, greater than 1s, or any threshold in between. To determine when to perform PBO, the phase monitor watches for phase changes greater than 100ns in a 10ms interval on the selected reference. When such a phase change occurs, an internal 0.1 second timer is started. If during this interval the phase change is greater than the PMLIM threshold then a PBO event occurs. During a PBO event the device enters a temporary holdover state in which the phase difference between the selected reference and the output is measured and fed into the DPLL loop to absorb the input transient. After a PBO event, regardless of the input phase transient, the output phase transient is less than or equal to 5ns. Phase build-out can be frozen at the current phase offset by setting MCR10:PBOFRZ = 1. When PBO is frozen the T0 DPLL ignores subsequent phase build-out events and maintains the current phase offset between input and outputs. 7.7.7.3 Phase Build-Out in Response to Reference Switching When MCR10:PBOEN = 0, phase build-out is not performed during reference switching, and the T0 DPLL always locks to the selected reference at zero degrees of phase. With PBO disabled, transitions from a failed reference to the next highest priority reference and transitions from holdover or free-run to locked mode cause phase transients on output clocks as the T0 DPLL jumps from its previous phase to the phase of the new selected reference. When MCR10:PBOEN = 1, phase build-out is performed during reference switching. With PBO enabled, if the selected reference fails and another valid reference is available then the device enters a temporary holdover state in which the phase difference between the new reference and the output is measured and fed into the DPLL loop to absorb the input phase difference. Similarly, during transitions from holdover or free-run to locked mode, the phase difference between the new reference and the output is measured and fed into the DPLL loop to absorb the input phase difference. After a PBO event, regardless of the input phase difference, the output phase transient is less than or equal to 5ns. Any time that PBO is enabled it can also be frozen at the current phase offset by setting MCR10:PBOFRZ = 1. When PBO is frozen the T0 DPLL ignores subsequent phase build-out events and maintains the current phase offset between inputs and outputs. Disabling PBO while the T0 DPLL is in the locked state causes a phase change on the output clocks while the DPLL switches to tracking the selected reference with 0 degrees of phase error. The rate of phase change on the output clocks depends on the DPLL bandwidth. Enabling PBO in the locked state also causes a PBO event.
19-4546; Rev 9; 5/09
40 of 227
DS3100 7.7.7.4 Manual Phase Build-Out Control
Software can have manual control over phase build-out, if required. Initial configuration for manual PBO involves locking to an input clock with frequency 6.48MHz, setting MCR10:PBOEN = 0 and PHMON:PMPBEN = 0 to disable automatic phase build-out, and setting PHMON:PMEN = 1 and the proper phase limit in PHMON:PMLIM to enable monitoring for a phase transient. During operation, software can monitor for either a phase transient (MSR3:PHMON = 1) or a T0 DPLL state change (MSR2:STATE = 1). When either event occurs, software can perform the following procedure to execute a manual phase build-out (PBO) event: 1) Read the phase offset from the PHASE registers to decide whether or not to initiate a PBO event. 2) If a PBO event is desired then save the phase offset and set MCR10:PBOEN to cause a PBO event. 3) When the PBO event is complete (wait for a timeout and/or PHASE = 0), write the manual phase offset registers (OFFSET) with the phase offset read earlier. (Note: the PHASE register is in degrees, the OFFSET register is in picoseconds) 4) Clear MCR10:PBOEN and wait for the next event that may need a manual PBO. 7.7.7.5 PBO Phase Offset An uncertainty of up to 5ns is introduced each time a phase build-out event occurs. This uncertainty results in a phase hit on the output. Over a large number of phase build-out events the mean error should be zero. The PBOFF register specifies a small fixed offset for each phase build-out event to skew the average error toward zero and eliminate accumulation of phase shifts in one direction.
7.7.8
Input to Output Phase Adjustment
When phase build-out is disabled (PBOEN = 0 in MCR10 and PMPBEN = 0 in PHMON), the OFFSET registers can be used to adjust the phase of the T0 DPLL output clocks with respect to the selected reference. Output phase offset can be adjusted over a 200ns range in 6ps increments. This phase adjustment occurs in the feedback clock so that the output clocks are adjusted to compensate. The rate of change is therefore a function of DPLL bandwidth. To quickly track large changes in phase, either LOCK8K mode (Section 7.4.2.2) or the coarse phase detector (Section 7.7.5) should be used. Simply writing to the OFFSET registers with phase build-out disabled causes a change in the input to output phase which can be considered to be a delay adjustment.
7.7.9
Phase Recalibration
When a phase build-out occurs, either automatic or manual, the feedback frequency synthesizer does not get an internal alignment signal to keep it aligned with the output dividers, and therefore the phase difference between input and output may become incorrect. This could occur if there is a power supply glitch or EMI event that affects the sequential logic state machines. Setting the FSCR3:RECAL bit periodically causes a recalibration process to be executed, which corrects any phase error that may have occurred. During the recalibration process the device puts the DPLL into mini holdover, internally ramps the phase offset to zero, resets all clock dividers, ramps the phase offset to the value stored in the OFFSET registers, and then switches the DPLL out of mini holdover. If the OFFSET registers are written during the recalibration process, the process will ramp the phase offset to the new offset value.
7.7.10
Frequency and Phase Measurement
Standard input clock frequency monitoring is described in Section 7.5.1. The input clock monitors report measured frequency with 3.8ppm resolution. More accurate measurement of frequency and phase can be accomplished using the DPLLs. The T0 DPLL is always monitoring its selected reference, but if the T4 DPLL is not otherwise used then it can be configured as a high-resolution frequency and phase monitor. Software can then connect the T4 DPLL to various input clocks on a rotating basis to measure frequency and phase. See MCR4:T4FORCE. DPLL frequency measurements can be read from the FREQ field spanning registers FREQ1, FREQ2 and FREQ3. This field indicates the frequency of the selected reference for either the T0 DPLL or the T4 DPLL, depending on the setting of the T4T0 bit in MCR11. This frequency measurement has a resolution of 0.0003068ppm over a 80ppm range. The value read from the FREQ field is the DPLL's integral path value, which is an averaged measurement with an averaging time inversely proportional to DPLL bandwidth. DPLL phase measurements can be read from the PHASE field spanning registers PHASE1 and PHASE2. This field indicates the phase difference seen by the phase detector for either the T0 DPLL or the T4 DPLL, depending 19-4546; Rev 9; 5/09 41 of 227
DS3100 on the setting of the T4T0 bit in MCR11. This phase measurement has a resolution of approximately 0.7 degrees and is internally averaged with a -3dB attenuation point of approximately 100Hz. Thus, for low DPLL bandwidths the PHASE field gives input phase wander in the frequency band from the DPLL corner frequency up to 100Hz. This information could be used by software to compute a crude MTIE measurement up to an observation time of approximately 1000 seconds. For the T0 DPLL, the PHASE field always indicates the phase difference between the selected reference and the internal feedback clock. The T4 DPLL, however, can be configured to measure the phase difference between two input clocks. When T0CR1:T4MT0 = 1, the T4 path is disabled and the T4 phase detector is configured to compare the T0 DPLL selected reference with the T4 DPLL selected reference. Any input clock can then be forced to be the T4 DPLL selected reference using the T4FORCE field of MCR4. This feature can be used, for example, to measure the phase difference between the T0 DPLL's selected reference and its next highest priority reference. Software could compute MTIE and TDEV with respect to the selected reference for any or all of the other input clocks. When comparing the phase of the T0 and T4 selected references by setting T0CR1:T4MT0 = 1, several details must be kept in mind. In this mode, the T4 path receives a copy of the T0 selected reference, either directly or through a divider to 8kHz. If the T4 selected reference is divided down to 8kHz using LOCK8K or DIVN modes (see Section 7.4.2), then the copy of the T0 selected reference is also divided down to 8kHz. If the T4 selected reference is configured for direct-lock mode, then the copy of the T0 selected reference is not divided down and must be the same frequency as the T4 selected reference. See Table 7-6 for more details. (While T0CR1:T4MT0 = 1 the T0 path continues to lock to the T0 selected reference in the manner specified in the corresponding ICR register.)
Table 7-6. T0 Adaptation for T4 Phase Measurement Mode
LOCKING MODE FOR T4 SELECTED REFERENCE DIVN or LOCK8K DIVN or LOCK8K DIVN or LOCK8K DIRECT
Note 1: Note 2:
LOCKING MODE FOR T0 SELECTED REFERENCE DIRECT LOCK8K DIVN Any
LOCKING MODE FOR COPY OF T0 SELECTED REF LOCK8K LOCK8K DIVN DIRECT
FREQUENCY OF THE T4 SELECTED REF FOR T4/T0 PHASE MEASUREMENT 8kHz 8kHz 8kHz Same as the T4 selected ref input frequency
FREQUENCY OF THE T0 SELECTED REF FOR T4/T0 PHASE MEASUREMENT 8kHz 8kHz 8kHz Same as the T0 selected ref input frequency(1)
In this case, the T0 select reference must be the same frequency as the T4 selected reference. If the T4 selected reference frequency is 8kHz and the T0 selected reference is a different frequency, the two references can be compared by configuring the T4 selected reference for 8 kHz and LOCK8K mode. This forces the copy of the T0 selected reference to be divided down to 8kHz using either LOCK8K or DIVN mode.
7.7.11
Input Wander and Jitter Tolerance
The device is compliant with the jitter and wander tolerance requirements of the standards listed in Table 1-1. Wander is tolerated up to the point where wander causes an apparent long-term frequency offset larger than the limits specified in the ILIMIT and/or SRLIMIT registers. In such a situation the input clock would be declared invalid. Jitter is tolerated up to the point of eye closure. Either LOCK8K mode (see Section 7.4.2.2) or the multicycle phase detector (see Section 7.7.5) should be used for high jitter tolerance.
7.7.12
Jitter and Wander Transfer
In the DS3100, the transfer of jitter and wander from the selected reference to the output clocks has a programmable transfer function that is determined by the DPLL bandwidth. (See Section 7.7.3.) In the T0 DPLL, the 3dB corner frequency of the jitter transfer function can be set to any of 18 positions from 0.5mHz to 70Hz. In the T4 DPLL, the 3dB corner frequency of the jitter transfer function can be set to 18Hz, 35Hz, or 70Hz. During locked mode, the transfer of wander from the local oscillator clock (connected to the REFCLK pin) to the output clocks is not significant as long as the DPLL bandwidth is set high enough to allow the DPLL to quickly compensate for oscillator frequency changes. During free-run and holdover modes, local oscillator wander has a much more significant effect. See Section 7.3. 19-4546; Rev 9; 5/09 42 of 227
DS3100
7.7.13
Output Jitter and Wander
Several factors contribute to jitter and wander on the output clocks, including: Jitter and wander amplitude on the selected reference (while in the locked state) The jitter/wander transfer characteristic of the device (while in the locked state) The jitter and wander on the local oscillator clock signal (especially wander while in the holdover state) The DPLL in the device has programmable bandwidth (see Section 7.7.3). With respect to jitter and wander, the DPLL behaves as a low-pass filter with a programmable pole. The bandwidth of the DPLL is normally set low enough to strongly attenuate jitter. The wander attenuation depends on the DPLL bandwidth chosen. Over time frequency changes in the local oscillator can cause a phase difference between the selected reference and the output clocks. This is especially true at DPLL bandwidths of 0.1Hz and below because the DPLL's rate of change may be slower than the oscillator's rate of change. Oscillators with better stability will minimize this effect. In some applications an OCXO may be required rather than a TCXO. In the most demand applications, the OCXO may need to be shielded to further reduce the rate of temperature change and thus the rate of frequency change. Typical MTIE and TDEV measurements for the DS3100 in locked mode are shown in Figure 7-3 and Figure 7-4, respectively.
Figure 7-3. Typical MTIE for T0 DPLL Output
1000
100 MTIE (ns)
G.813 Option 1 constant temperature mask
10
Measured MTIE, 19.44 MHz Input and Output, 4 Hz Bandwidth, DS4026 TCXO
1
0.1 0.01
0.1
1
10 Obs e rvation Inte rval (s )
100
1000
10000
19-4546; Rev 9; 5/09
43 of 227
DS3100
Figure 7-4. Typical TDEV for T0 DPLL Output
10
1 TDEV (ns)
G.813 Option 1 constant temperature mask
0.1
Measured TDEV, 19.44 MHz Input and Output, 4 Hz Bandwidth, DS4026 TCXO
0.01
0.001 0.01
0.1
1
10 Obs e rvation Inte rnval (s )
100
1000
10000
7.8
Output Clock Configuration
A total of 11 output clock pins, OC1 to OC11, are available on the device. Output clocks OC1 to OC7 are individually configurable for a variety of frequencies derived from either the T0 DPLL path or the T4 DPLL path. Output clocks OC8 to OC11 are more specialized, serving as a dedicated composite clock transmitter (OC8), a 1544/2.048kHz clock (OC9), an 8kHz frame sync (OC10), and a 2kHz multiframe sync (OC11). Table 7-7 provides more detail on the capabilities of the output clocks.
Table 7-7. Output Clock Capabilities
OUTPUT CLOCK OC1 OC2 OC3 OC4 OC5 OC6 OC7 OC8 OC9 OC10 OC11 SIGNAL FORMAT CMOS/TTL CMOS/TTL CMOS/TTL CMOS/TTL CMOS/TTL LVDS LVDS AMI CMOS/TTL CMOS/TTL CMOS/TTL FREQUENCIES SUPPORTED
Frequency selection per Section 7.8.2.3 and Table 7-9 through Table 7-12
64kHz composite clock 1.544MHz or 2.048MHz 8kHz frame sync with programmable pulse width and polarity 2kHz multiframe sync with programmable pulse width and polarity
19-4546; Rev 9; 5/09
44 of 227
DS3100
7.8.1
Signal Format Configuration
Output clocks OC6 and OC7 are enabled and disabled via the OC6SF and OC7SF configuration bits in the MCR8 register. The LVDS electrical specifications are listed in Table 10-4, and the recommended LVDS termination is shown in Figure 10-1. These outputs can be easily interfaced to LVPECL and CML inputs on neighboring ICs using a few external passive components. See Maxim App Note HFAN-1.0 for details. Output clock OC8 is a dedicated composite clock (CC) transmitter. The composite clock signal is a 64kHz AMI clock with an embedded 8kHz clock indicated by deliberate bipolar violations (BPVs) every 8 clock cycles. See Section 7.11.2 for OC8 configuration details. The AMI CC electrical specifications are shown in Table 10-6, and the recommended external components are shown in Table 10-3. Output clocks OC1 to OC5 and OC9 to OC11 are always CMOS/TTL signal format.
7.8.2
Frequency Configuration
The frequency of most of the output clocks is a function of the settings used to configure the components of the T0 and T4 PLL paths. These components are shown in the detailed block diagram of Figure 7-5. The T0 and T4 PLLs use digital frequency synthesis (DFS) to generate various clocks. In DFS, a high-speed master clock (204.8MHz) is divided down to the desired output frequency. The edges of the output clock, however, are not ideally located in time but rather are aligned with the edges of the master clock resulting in jitter with an amplitude equal to 1 period of the master clock (i.e., 4.88ns). 7.8.2.1 T0 DPLL and APLL Details The 77M forward DFS block (see Figure 7-5) uses the 204.8MHz master clock and DFS to synthesize a 77.76MHz clock with 4.88ns inherent peak-to-peak jitter. This clock can be fed directly to the feedback DFS block or it can be passed through the feedback APLL to reduce jitter to less than 1ns. The 77M forward DFS block handles phase build-out and any phase offset configured in the OFFSET registers. Thus, the 77M output DFS block and the 77M forward DFS block are frequency locked but may have a phase offset. The feedback DFS block takes as its input clock either the output from the 77M forward DFS or the jitter-filtered output from the T0 feedback APLL. The feedback DFS block synthesizes the appropriate locking frequency for use in the phase-frequency detector (PFD). The 77M output DFS block also uses the 204.8MHz master clock and DFS to synthesize a 77.76MHz clock with 4.88ns peak-to-peak jitter. This clock goes to both the output APLL and the low frequency (LF) output DFS block.
19-4546; Rev 9; 5/09
45 of 227
DS3100
Figure 7-5. DPLL Block Diagram
0 MCR4:LKT4T0 T4CR1:T4FREQ[3:0] 1 MCR4:T4DFB
T4 LF Output DFS
0
T4 selected reference
0 1
T4 PFD and Loop Filter
0 Locking Frequency 1
T4 Foward DFS T4 Feedback DFS
T0 selected reference
MCR4:T4DFB 1 0
1 T0CR1:T4APT0
T4 Output APLL
T4 Output Dividers
0
T0CR1:T4MT0
OC8, OC9
1
8 kHz
T4 Path
MCR4:OC89
T0 LF Output DFS T0 77M Output DFS T0 selected reference T0 PFD and Loop Filter T0 77M Foward DFS T0 Feedback DFS
1 0 T0CR1:T0FREQ[2:0]=000 T0CR1:T0FREQ[2:0]
OC10, OC11
T0 Output APLL
T0CR1:T0FREQ[2:0]
T0 Output Dividers
OC1 to OC7
T0 Feedback APLL
OCRm:OFREQn[3:0] FSCR1:2K8KSRC
Locking Frequency
T0 Path
The LF output DFS block takes as its input clock either the output from the 77M output DFS or the jitter-filtered output of the output APLL. The LF output DFS block synthesizes three frequencies: Digital1, Digital2, and a third frequency for producing multiple N x DS1/E1 rates via the output APLLs. When the output APLL uses the output from the LF output DFS, the LF output DFS uses the output from the 77M output DFS block to avoid a loop. The LF output DFS also synthesizes frequencies for use by output clocks OC8, OC9, OC10, and OC11. The frequency of the Digital1 clock is configured by the DIG1SS bit in MCR6 and the DIG1F[1:0] field in MCR7. The frequency of the Digital2 clock is configured by the DIG2AF and DIG2SS bits in MCR6 and the DIG2F[1:0] field in MCR7. Digital1 and Digital2 can be independently configured for any of the frequencies shown in Table 7-8. Because they are generated by DFS and cannot be filtered by an APLL, Digital1 and Digital2 have relatively highamplitude jitter. The minimum jitter is approximately 12ns (one period of the input clock to the LF output DFS) when the T0 path is in analog feedback mode. The maximum jitter is approximately 17ns when T0 is in digital feedback mode. Both the Digital1 and Digital2 rates are available to output clocks OC1 to OC7. The output APLL takes as its input clock either the output of the 77M output DFS or one of the frequencies from the LF output DFS (77.76MHz, 16 x DS1, 24 x DS1, 12 x E1, or 16 x E1). The output frequency of the output APLL is four times the input frequency (e.g., 311.04MHz for 77.76MHz input). The output clock is then divided by 1, 2, 4, 6, 8, 12, 16, and 48. These clock rates are available to the OC1 to OC7 output clocks. 19-4546; Rev 9; 5/09 46 of 227
DS3100
Table 7-8. Digital1 and Digital2 Frequencies
DIGxF[1:0] SETTING IN MCR7 00 01 10 11 00 01 10 11 DIGxSS SETTING IN MCR6 0 0 0 0 1 1 1 1 FREQUENCY (MHz) 2.048 4.096 8.192 16.384 1.544 3.088 6.176 12.352
Note: When MCR6:DIG2AF = 1, Digital2 generates 6312kHz (must set MCR6:DIG2SS = 0 and MCR7:DIG2F = 00).
7.8.2.2
T4 DPLL and APLL Details
The T4 path is simpler than the T0 path and does not support phase build-out or phase offset. The T4 path can be locked to an input clock or to the T0 path (by setting LKT4T0=1 in MCR4). Using the 204.8MHz master clock and DFS, the T4 forward DFS block generates a clock with 4.88 ns inherent peak-to-peak jitter at any of the following frequencies: 16 x DS1, 24 x DS1, 12 x E1, 16 x E1, DS3, 2 x E3, 62.5MHz, or 77.76MHz. This clock can be fed directly to the T4 feedback DFS block (T4DFB = 1 in MCR4), or it can be passed through the T4 output APLL to reduce jitter to less than 1ns (T4DFB = 0). The T4 feedback DFS block takes as its input clock either the output from the T4 forward DFS or the jitter-filtered output from the T4 output APLL, depending on the setting of MCR4:T4DFB. The T4 feedback DFS block synthesizes the appropriate locking frequency for use in the T4 phase-frequency detector (PFD). The T4 output APLL filters jitter to less than 1 ns and takes as its input clock either the output of the T4 forward DFS block or one of the frequencies from the T0 LF output DFS (16xDS1, 24xDS1, 12xE1, 16xE1 or 4x6312kHz, as specified by T0CR1:T0FT4[2:0]). The output frequency of the output APLL is four times the input frequency (e.g., 311.04MHz for 77.76MHz input). The output clock is then divided by 2, 4, 8, 16, 48, and 64. These clock rates are available to the OC1 to OC7 output clocks. The T4 LF output DFS block normally takes as its input clock the jitter-filtered output of the T4 output APLL. When the T4 output APLL is connected to the T0 LF output DFS (T0CR1:T4APT0 = 1), the T4 output APLL must be disconnected from the T4 DPLL loop by configuring the loop for digital feedback (MCR4:T4DFB = 1). In this situation the T4 LF output DFS takes its input from the T4 forward DFS block. The T4 LF output DFS block generates 2kHz and 8kHz frequencies for use by output clocks OC1 to OC7 (when FSCR1:2K8KSRC = 1) and synthesizes frequencies for use by output clocks OC8 and OC9 (when MCR4:OC89 = 1).
19-4546; Rev 9; 5/09
47 of 227
DS3100 7.8.2.3 OC1 to OC7 Configuration
The following is a step-by-step procedure for configuring the frequencies of output clocks OC1 to OC7: 1) Determine whether the T4 path must be independent of the T0 path or not. If the T4 path must be independent, set T4APT0 = 0 in register T0CR1. If the T4 path can be locked to the T0 path then set T4APT0 = 1. 2) Use Table 7-9 to select a set of output frequencies for each path, T0 and T4. Each path can only generate one set of output frequencies. (In SONET/SDH equipment the T0 path is typically configured for an APLL frequency of 311.04MHz in order to get 19.44MHz and/or 38.88MHz output clocks to distribute to system line cards.) 3) Determine from Table 7-9 the T0 and T4 APLL frequencies required for the frequency sets chosen in step 2. 4) Configure the T0FREQ field in register T0CR1 as shown in Table 7-10 for the T0 APLL frequency determined in step 3. Configure the T4FREQ field in register T4CR1 as shown in Table 7-11 for the T4 APLL frequency determined in step 3. If the T4 APLL is locked to the T0 DPLL then the T0FT4 field in T0CR1 must also be configured as shown in Table 7-11. 5) Using Table 7-9 and Table 7-12, configure the frequencies of output clocks OC1 through OC7 in the OFREQn fields of registers OCR1 to OCR4. 6) If any of OC1 to OC7 are configured for 2kHz or 8kHz frequency, set 2K8KSRC = 0 in FSCR1 to source these frequencies from the T0 path or 2K8KSRC = 1 to source these frequencies from the T4 path. Table 7-13 lists all possible frequencies for output clocks OC1 to OC7 and specifies how to configure the T0 path and/or the T4 path to obtain each frequency. Table 7-13 also indicates the expected jitter amplitude for each frequency.
Table 7-9. APLL Frequency to Output Frequencies (T0 and T4)
APLL FREQUENCY 311.04 274.944 250.000 178.944 148.224 131.072 100.992 98.816 98.304 APLL/2 155.52 137.472 125.000 89.472 74.112 65.536 50.496 49.408 49.152 APLL/4 77.76 68.736 62.500 44.736 37.056 32.768 25.248 24.704 24.576 APLL/6 51.84 -- -- -- 24.704 21.84533 16.832 16.46933 16.384 APLL/8 38.88 34.368 31.250 22.368 18.528 16.384 12.624 12.352 12.288 APLL/12 25.92 -- -- -- 12.352 10.92267 8.416 8.23467 8.192 APLL/16 19.44 17.184 15.625 11.184 9.264 8.192 6.312 6.176 6.144 APLL/48 6.48 5.728 5.2083 3.728 3.088 2.73067 2.104 2.05867 2.048 APLL/64 4.86 4.296 3.90625 2.796 2.316 2.048 1.578 1.544 1.536
Note: All frequencies in MHz. Common telecom frequencies are in bold type.
Table 7-10. T0 APLL Frequency to T0 Path Configuration
T0 APLL FREQUENCY (MHz) 311.04 311.04 98.304 131.072 148.224 98.816 100.992 T0 FREQUENCY MODE 77.76MHz, digital feedback 77.7MHz, analog feedback 12 x E1 (digital feedback) 16 x E1 (digital feedback) 24 x DS1 (digital feedback) 16 x DS1 (digital feedback) 4 x 6312kHz (digital feedback) T0FREQ[2:0] SETTING IN T0CR1 000 001 010 011 100 101 110 OUTPUT JITTER (pk-pk, ns) < 0.5 < 0.5 <2 <2 <2 <2 <2
19-4546; Rev 9; 5/09
48 of 227
DS3100
Table 7-11. T4 APLL Frequency to T4 Path Configuration
T4 APLL FREQUENCY (MHz) 311.04 311.04 98.304 131.072 148.224 98.816 274.944 178.944 100.992 250.000 98.304 131.072 148.224 98.816 100.992 T4 FREQUENCY MODE Squelched Normal 12 x E1 16 x E1 24 x DS1 16 x DS1 2 x E3 DS3 4 x 6312 kHz GbE / 16 T0 12 x E1 T0 16 x E1 T0 24 x DS1 T0 16 x DS1 4 x 6312kHz T4 FORWARD DFS FREQ (MHz) 77.76 77.76 24.576 32.768 37.056 24.704 68.736 44.736 25.248 62.500 -- -- -- -- -- T4APT0 SETTING IN T0CR1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 T4FREQ[3:0] SETTING IN T4CR1 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 XXXX XXXX XXXX XXXX XXXX T0FT4[2:0] SETTING IN T0CR1 XXX XXX XXX XXX XXX XXX XXX XXX XXX XXX 000 010 100 110 111 OUTPUT JITTER (pk-pk, ns) < 0.5 < 0.5 < 0.5 < 0.5 < 0.5 < 0.5 < 0.5 < 0.5 < 0.5 < 0.5 <2 <2 <2 <2 <2
19-4546; Rev 9; 5/09
49 of 227
DS3100
Table 7-12. OC1 to OC7 Output Frequency Selection
REGISTER VALUE(1) 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111
FREQUENCY
OC1 Disabled 2kHz 8kHz Digital2 Digital1 T0 APLL/48 T0 APLL/16 T0 APLL/12 T0 APLL/8 T0 APLL/6 T0 APLL/4 T4 APLL/64 T4 APLL/48 T4 APLL/16 T4 APLL/8 T4 APLL/4 OC2 Disabled 2kHz 8kHz Digital2 Digital1 T0 APLL/48 T0 APLL/16 T0 APLL/12 T0 APLL/8 T0 APLL/6 T0 APLL/4 T4 APLL/64 T4 APLL/48 T4 APLL/16 T4 APLL/8 T4 APLL/4 OC3 Disabled 2kHz 8kHz Digital2 Digital1 T0 APLL/48 T0 APLL/16 T0 APLL/12 T0 APLL/8 T0 APLL/6 T0 APLL/4 T4 APLL/64 T4 APLL/48 T4 APLL/16 T4 APLL/8 T4 APLL/4 OC4 Disabled 2kHz 8kHz Digital2 Digital1 T0 APLL/48 T0 APLL/16 T0 APLL/12 T0 APLL/8 T0 APLL/6 T0 APLL/4 T4 APLL/2 T4 APLL/48 T4 APLL/16 T4 APLL/8 T4 APLL/4 OC5 Disabled 2kHz 8kHz Digital2 Digital1 T0 APLL/48 T0 APLL/16 T0 APLL/12 T0 APLL/8 T0 APLL/6 T0 APLL/4 T4 APLL/2 T4 APLL/48 T4 APLL/16 T4 APLL/8 T4 APLL/4 OC6 Disabled 2kHz 8kHz T0 APLL/2 Digital1 T0 APLL/1 T0 APLL/16 T0 APLL/12 T0 APLL/8 T0 APLL/6 T0 APLL/4 T4 APLL/64 T4 APLL/48 T4 APLL/16 T4 APLL/8 T4 APLL/4 OC7 Disabled 2kHz 8kHz Digital2 T0 APLL/2 T0 APLL/48 T0 APLL/16 T0 APLL/12 T0 APLL/8 T0 APLL/6 T0 APLL/4 T4 APLL/64 T4 APLL/48 T4 APLL/16 T4 APLL/8 T4 APLL/4
Note 1: The value of the OFREQn field (in the OCR1 through OCR4 registers) corresponding to output clock OCn.
Table 7-13. Possible Frequencies for OC1 to OC7
FREQUENCY (MHz) 2kHz 2kHz 8kHz 8kHz 1.536 1.536 1.544 1.544 1.544 1.544 1.544 1.544 1.578 1.578 2.048 2.048 2.048 2.048 2.048 2.048 2.048 2.048 2.048 2.059 2.059 2.059 2.104 2.104 2.104 2.316 2.316 2.731 2.731 2.731 T0 DPLL MODE 77.76MHz, analog Any digital feedback 77.76MHz, analog Any digital feedback Not OC4 or OC5 Not OC4 or OC5 Via Digital1, not OC7 Via Digital2, not OC6 Via Digital1, not OC7 Via Digital2, not OC6 Not OC4 or OC5 Not OC4 or OC5 Not OC4 or OC5 Not OC4 or OC5 Not OC6 Via Digital1, not OC7 Via Digital2, not OC6 Via Digital1, not OC7 Via Digital2, not OC6 Not OC4 or OC5 Not OC4 or OC5 Not OC6 Not OC6 -- T4 DPLL MODE -- T4 APLL SOURCE OFREQN SETTING 0001 0001 0010 0010 1011 1011 0100 0011 0100 0011 1011 1011 1011 1011 0101 0100 0011 0100 0011 1100 1100 1011 1011 0101 1100 1100 0101 1100 1100 1011 1011 0101 1100 1100 JITTER (TYP) RMS pk-pk (ps) (ns) 60 0.6 1400 5.0 60 0.6 1400 5.0 55 0.6 250 1.5 3800 13 3800 13 3800 18 3800 18 140 1.2 275 1.9 240 1.5 260 1.8 425 2.6 3800 13 3800 13 3800 18 3800 18 55 0.6 250 1.5 50 0.5 350 2.4 435 2.8 140 1.2 275 1.9 340 2.3 240 1.8 260 1.8 150 1.0 400 2.8 380 2.6 50 0.5 350 2.4
12 x E1 77.76MHz, analog 77.76MHz, analog Any digital feedback Any digital feedback 16 x DS1 4 x 6312kHz 12 x E1 mode 77.76MHz, analog 77.76MHz, analog Any digital feedback Any digital feedback 12 x E1 16 x E1 16 x DS1 16 x DS1 4 x 6312 kHz 4 x 6312kHz
T4 DPLL T0 12 x E1
T4 DPLL T0 16 x DS1 T4 DPLL T0 4x6312kHz
T4 DPLL T0 12 x E1 T4 DPLL T0 16 x E1 T4 DPLL T0 16 x DS1 T4 DPLL T0 4x6312kHz T4 DPLL T0 24 x DS1 T4 DPLL T0 16 x E1
Not OC4 or OC5 Not OC4 or OC5 Not OC6
24 x DS1 16 x E1 16 x E1
19-4546; Rev 9; 5/09
50 of 227
DS3100
T4 DPLL MODE DS3 24 x DS1 77.76MHz, analog 77.76MHz, analog Any digital feedback Any digital feedback 24 x DS1 DS3 GbE / 16 T4 DPLL T0 24 x DS1 T4 DPLL T4 DPLL T4 APLL SOURCE T4 DPLL OFREQN SETTING 1011 0101 0100 0011 0100 0011 1100 1100 1100 1011 0100 0011 0100 0011 1011 1011 1100 1100 0110 1101 1101 0110 0100 0011 0100 0011 1101 1101 0110 0011 0011 1101 1101 0101 0101 1100 0111 0110 0100 0011 0100 0011 1101 1101 0111 0111 0110 1101 1101 0111 1101 1000 1110 1110 0111 1000 1110 1110 0100 JITTER (TYP) RMS pk-pk (ps) (ns) 80 0.7 400 2.8 3800 13 3800 13 3800 18 3800 18 150 1.0 400 2.8 80 0.7 70 0.6 3800 13 3800 13 3800 18 3800 18 350 2.0 60 0.6 70 0.6 350 2.0 425 2.6 55 0.6 250 1.5 435 2.8 3800 13 3800 13 3800 18 3800 18 140 1.2 275 1.9 340 2.3 3800 13 3800 18 240 1.8 260 1.8 60 0.6 60 0.6 60 0.6 425 2.6 380 2.6 3800 13 3800 13 3800 18 3800 18 50 0.5 350 2.4 435 2.8 340 2.3 400 2.8 150 1.0 400 2.8 380 2.6 80 0.7 425 2.6 55 0.6 250 1.5 400 2.8 435 2.8 140 1.2 275 1.9 3800 13
FREQUENCY (MHz) 2.796 3.088 3.088 3.088 3.088 3.088 3.088 3.088 3.728 3.90625 4.096 4.096 4.096 4.096 4.296 4.86 5.2083 5.728 6.144 6.144 6.144 6.176 6.176 6.176 6.176 6.176 6.176 6.176 6.312 6.312 6.312 6.312 6.312 6.48 6.48 6.48 8.192 8.192 8.192 8.192 8.192 8.192 8.192 8.192 8.235 8.416 9.264 9.264 9.264 10.923 11.184 12.288 12.288 12.288 12.352 12.352 12.352 12.352 12.352 Not OC4 or OC5 Not OC6 Via Digital1, not OC7 Via Digital2, not OC6 Via Digital1, not OC7 Via Digital2, not OC6
T0 DPLL MODE
Not OC4 or OC5 Via Digital1, not OC7 Via Digital2, not OC6 Via Digital1, not OC7 Via Digital2, not OC6 Not OC4 or OC5 Not OC4 or OC5
77.76 MHz, analog 77.76 MHz, analog Any digital feedback Any digital feedback
2 x E3 77.76MHz GbE / 16 2 x E3 12 x E1 12 x E1
T4 DPLL T4 DPLL T4 DPLL T4 DPLL T4 DPLL T0 12 x E1
Via Digital1, not OC7 Via Digital2, not OC6 Via Digital1, not OC7 Via Digital2, not OC6
16 x DS1 77.76MHz, analog 77.76MHz, analog Any digital feedback Any digital feedback 16 x DS1 4 x 6312kHz 77.76MHz, analog Any digital feedback 4 x 6312kHz T4 DPLL T0 4 x 6312kHz 77.76MHz, analog 77.76MHz, digital 77.76 MHz T4 DPLL 12 x E1 16 x E1 77.76 MHz, analog 77.76 MHz, analog Any digital feedback Any digital feedback 16 x E1 16 x DS1 4 x 6312kHz 24 x DS1 24 x DS1 16 x E1 DS3 12 x E1 12 x E1 24 x DS1 16 x DS1 16 x DS1 T4 DPLL T0 16 x DS1 T4 DPLL T0 12 x E1 T4 DPLL T4 DPLL T0 24 x DS1 T4 DPLL T0 16 x E1 T4 DPLL T0 16 x DS1
Via Digital 2, not OC6 Via Digital 2, not OC6 Not OC6 Not OC6
Via Digital1, not OC7 Via Digital2, not OC6 Via Digital1, not OC7 Via Digital2, not OC6
Via Digital1, Not OC7
77.76MHz, analog
19-4546; Rev 9; 5/09
51 of 227
DS3100
T4 DPLL MODE T4 APLL SOURCE OFREQN SETTING 0011 0100 0011 1000 1110 1110 1101 1001 1000 1110 1110 0100 0011 0100 0011 1001 1001 1101 1000 1110 1110 0110 0110 1101 1001 1110 1010 1111 1111 1001 1010 1111 1111 1100 1010 1111 1111 0111 0111 1110 1010 1111 1111 1110 1010 1111 1111 1000 1000 1110 1111 0011/0100 1011 1011 0011/0100 1011 1011 0011/0100 1011 JITTER (TYP) RMS pk-pk (ps) (ns) 3800 13 3800 18 3800 18 340 2.3 240 1.8 260 1.8 70 0.6 425 2.6 380 2.6 50 0.5 275 1.9 3800 13 3800 13 3800 18 3800 18 435 2.8 340 2.3 350 2.0 400 2.8 150 1.0 400 2.8 60 0.6 60 0.6 60 0.6 380 2.6 80 0.7 425 2.6 55 0.6 250 1.5 400 2.8 435 2.8 140 1.2 275 1.9 70 0.6 340 2.3 240 1.8 260 1.8 60 0.6 60 0.6 70 0.6 380 2.6 50 0.5 350 2.4 350 2.0 400 2.8 150 1.0 400 2.8 60 0.6 60 0.6 60 0.6 80 0.7 425 2.6 55 0.6 250 1.5 435 2.8 140 1.2 275 1.9 340 2.3 240 1.8
FREQUENCY (MHz) 12.352 12.352 12.352 12.624 12.624 12.624 15.625 16.384 16.384 16.384 16.384 16.384 16.384 16.384 16.384 16.469 16.832 17.184 18.528 18.528 18.528 19.44 19.44 19.44 21.845 22.368 24.576 24.576 24.576 24.704 24.704 24.704 24.704 25.000 25.248 25.248 25.248 25.92 25.92 31.25 32.768 32.768 32.768 34.368 37.056 37.056 37.056 38.88 38.88 38.88 44.736 49.152 49.152 49.152 49.408 49.408 49.408 50.496 50.496 Via Digital2, Not OC6 Via Digital1, Not OC7 Via Digital2, Not OC6
T0 DPLL MODE 77.76MHz, analog Any digital feedback Any digital feedback 4 x 6312kHz
4 x 6312kHz GbE / 16 16 x E1 Via Digital1, Not OC7 Via Digital2, Not OC6 Via Digital1, Not OC7 Via Digital2, Not OC6 77.76MHz, analog 77.76MHz, analog Any digital feedback Any digital feedback 16 x DS1 4 x 6312kHz 2 x E3 24 x DS1 24 x DS1 77.76MHz, analog 77.76MHz, digital 77.76 MHz 16 x E1 DS3 12 x E1 12 x E1 24 x DS1 16 x DS1 16 x DS1 GbE / 16 4 x 6312kHz 77.76MHz, analog 77.76MHz, digital 16 x E1 GbE / 16 16 x E1 2 x E3 24 x DS1 24 x DS1 77.76MHz, analog 77.76MHz, digital 77.76MHz DS3 OC6 and OC7 Only OC4 and OC5 Only OC4 and OC5 Only OC6 and OC7 Only OC4 and OC5 Only OC4 and OC5 Only OC6 and OC7 Only OC4 and OC5 Only 12 x E1 12 x E1 16 x DS1 16 x DS1 4 x 6312kHz 4 x 6312kHz
T4 DPLL T0 4x6312kHz T4 DPLL
12 x E1 16 x E1
T4 DPLL T0 16 x DS1
T4 DPLL T4 DPLL T0 24 x DS1
T4 DPLL T4 DPLL T4 DPLL T0 12 x E1 T4 DPLL T0 16 x DS1 T4 DPLL T4 DPLL T0 4x6312kHz
4 x 6312kHz
T4 DPLL T4 DPLL T0 16 x E1 T4 DPLL T4 DPLL T0 24 x DS1 T4 DPLL T4 DPLL T4 DPLL T0 12 x E1 T4 DPLL T0 16 x DS1 T4 DPLL
19-4546; Rev 9; 5/09
52 of 227
DS3100
T4 DPLL MODE T4 APLL SOURCE T0 4 x 6312kHz 77.76MHz, analog 77.76MHz, digital OC6 and OC7 Only OC4 and OC5 Only OC4 and OC5 Only OC6 and OC7 Only OC4 and OC5 Only OC4 and OC5 Only 16 x E1 GbE / 16 16 x E1 2 x E3 24 x DS1 24 x DS1 77.76MHz, analog 77.76MHz, digital OC4 and OC5 Only OC6 Only OC6 Only OC6 Only OC5 Only OC6 Only OC4 and OC5 Only OC6 Only OC6 and OC7 Only OC6 and OC7 Only OC4 and OC5 Only OC6 Only OC6 Only 77.76MHz DS3 12 x E1 16 x DS1 4 x 6312kHz 16 x E1 24 x DS1 77.76MHz, analog 77.76MHz, digital 77.76MHz 77.76MHz, analog 77.76MHz, digital T4 DPLL GbE / 16 2 x E3 T4 DPLL T4 DPLL T4 DPLL T4 DPLL T0 24 x DS1 T4 DPLL T4 DPLL T0 16 x E1 T4 DPLL OFREQN SETTING 1011 1001 1001 1111 0011/0100 1011 1011 1111 0011/0100 1011 1011 1010 1010 1111 1011 0101 0101 0101 1011 0101 1011 0101 0011/0100 0011/0100 1011 0101 0101 JITTER (TYP) RMS pk-pk (ps) (ns) 260 1.8 60 0.6 60 0.6 70 0.6 380 2.6 50 0.5 350 2.4 350 2.0 400 2.8 150 1.0 400 2.8 60 0.6 60 0.6 60 0.6 80 0.7 425 2.6 435 2.8 340 2.3 70 0.6 380 2.6 350 2.0 400 2.8 60 0.6 60 0.6 60 0.6 60 0.6 60 0.6
FREQUENCY (MHz) 50.496 51.84 51.84 62.50 65.536 65.536 65.536 68.736 74.112 74.112 74.112 77.76 77.76 77.76 89.472 98.304 98.816 100.992 125.000 131.072 137.472 148.224 155.52 155.52 155.52 311.04 311.04 OC4 and OC5 Only
T0 DPLL MODE
7.8.2.4
OC8 and OC9 Configuration
Output clocks OC8 and OC9 are generated by digital frequency synthesis (DFS) from either the T0 path or the T4 path, depending on the setting of the OC89 bit in MCR4. When generated from the T4 path (OC89 = 0), if ASQUEL = 1 in T4CR1 then OC8 and OC9 are automatically squelched when T4 has no valid input references. OC8 is always a 64kHz composite clock transmitter and therefore does not require any frequency configuration. Being 64kHz, OC8 can be divided down directly from the source DFS block's input clock. The jitter on OC8 can range from 13ns to 17ns, depending on whether the DPLL is in analog or digital feedback mode. See Section 7.11.2 for additional OC8 configuration details. OC9 is always a DS1 or E1 clock. OC9 is enabled by setting OC9EN = 1 in the OCR4 register, and it is configured for DS1 or E1 with the OC9SON bit in T4CR1 (when OC89 = 0) or with the SONSDH bit in MCR3 (when OC89 = 1). OC9 must synthesized, rather than directly divided down, from the source DFS block's input clock. The jitter on OC9 is therefore a function of the jitter on the input clock and the jitter generated during synthesis. OC9 jitter can range from 11ns to 20ns. 7.8.2.5 OC10 and OC11 Configuration Output clocks OC10 and OC11 are always generated from the T0 path. OC10 is enabled by setting OC10EN = 1 in the OCR4 register, while OC11 is enabled by setting OC11EN = 1 in OCR4. When 8KPUL = 0 in FSCR1, OC10 is configured as an 8kHz clock with 50% duty cycle. When 8KPUL = 1, OC10 is an 8kHz frame sync that pulses low once every 125s with pulse width equal to one cycle of output clock OC3. When 8KINV = 1 in FSCR1, the clock or pulse polarity of OC10 is inverted. When 2KPUL = 0 in FSCR1, OC11 is configured as an 2kHz clock with 50% duty cycle. When 2KPUL = 1, OC11 is a 2kHz frame sync that pulses low once every 500s with pulse width equal to one cycle of output clock OC3. When 2KINV = 1 in FSCR1, the clock or pulse polarity of OC11 is inverted.
19-4546; Rev 9; 5/09
53 of 227
DS3100 If either 8KPUL = 1 or 2KPUL = 1, then output clock OC3 must be generated from the T0 DPLL and must be configured for a frequency of 1.544MHz or higher or the OC10/OC11 pulses may not be generated correctly. Figure 7-6 shows how the 8KPUL and 8KINV control bits affect the OC10 output. The 2KPUL and 2KINV bits have an identical effect on OC11.
Figure 7-6. OC10 8kHz Options
OC3 output clock OC10, 8KPUL=0, 8KINV=0 OC10, 8KPUL=0, 8KINV=1 OC10, 8KPUL=1, 8KINV=0 OC10, 8KPUL=1, 8KINV=1
7.9
Equipment Redundancy Configuration
Most high-reliability SONET/SDH systems require two identical timing cards for equipment redundancy. The DS3100 directly supports this requirement. In such a system one timing cards is designated the master while the other is designated the slave. The rest of the system, outside the timing cards, is set up to take timing from the master normally, but to automatically switch to taking timing from the slave if the master fails. To avoid excessive phase transients when switching between master timing and slave timing, the clocks from the master and the slave must be frequency locked and usually phase locked as well. To accomplish this requires a method involving both static configuration and ongoing oversight by system software. The elements of this methodology are listed in Table 7-14.
Table 7-14. Equipment Redundancy Methodology
1. The various clock sources available in the system should be wired to the same pins on the slave as on the master, except: A. One output clock from the master device should be wired to an input clock on the slave. B. One output clock from the slave device should be wired to an input clock on the master. The input clock priorities (IPR registers) on master and slave should be identical, for both T0 and T4 paths, except: A. The master output clock is the highest priority input on the slave(1) B. The slave output clock is disabled (priority 0) on the master This ensures that the frequency of the slave matches the frequency of the master. Any input declared invalid in one device (VALSR registers) must be marked invalid by software in the other device (VALCR registers). This and item 2 together ensure that when the master is performing properly, the slave locks to the master, and when the master fails, the slave locks to the input clock the master was previously locked to. The slave's T0 DPLL bandwidth should be set higher than the master's (T0LBW, T0ABW registers) to ensure that the slave follows any transients coming from the master. (70Hz is recommended.) Phase build-out should be disabled (MCR10:PBOEN = 0 and PHMON:PMPBEN = 0) on the slave when it is locked to the master to ensure that the slave maintains phase lock with the master. This also allows the use of phase offset (OFFSET registers) to compensate for delays between master and slave. Revertive mode should be enabled on the slave (REVERT = 1 in MCR3) to ensure the slave switches from any other reference to the master as soon as the master's clock is valid.
2.
3.
4. 5. 6.
Note 1: This must be done for the slave's T0 path, but is not necessary for the slave's T4 path. In the slave's T4 path the input clock priorities should match those of the master except the input connected to the master's output clock should be disabled. This causes the slave's T4 path to only lock to external references.
19-4546; Rev 9; 5/09
54 of 227
DS3100
7.9.1
Master-Slave Pin Feature
Some of the elements of redundancy configuration listed in Table 7-14 are automatically handled in the device when the master-slave pin feature is used (MASTSLV). When this feature is supported in a system, one output clock of the master device must be wired to input clock IC11 on the slave device, and one output clock of the slave device should be wired to IC11 on the master device. This cross-wiring allows the system to dynamically configure either device as master and the other as slave. When the MASTSLV pin is wired low on one device, that device is configured as the slave. The other device must be configured as the master by wiring its MASTSLV pin high. In each device the state of the MASTSLV pin is always indicated in the read-only MASTSLV bit in register MCR3. The slave device (MASTSLV = 0) is automatically configured as follows: The priority of input clock IC11 is set to 1 (highest) (IPR6:PRI11[3:0] = 0001). Phase build-out is disabled (MCR10:PBOEN = 0). Revertive mode is enabled (MCR3:REVERT = 1). T0 DPLL bandwidth is forced to the acquisition setting (i.e., to the setting in the T0ABW register, which should be set to a high bandwidth by software). In the master device (MASTSLV = 1), none of these settings are forced to specific values. Rather, each setting is configured as needed for normal operation of the system. During configuration, software should configure the master to disable (priority 0) input clock IC11 and should configure the remaining input clock priorities identically in master and slave. During operation, software must maintain matching input clock priorities, as described in item 3 of Table 7-14. The master-slave pin feature is optional and can be disabled by wiring the MASTSLV pin high on both devices. If this feature is disabled, all the elements of equipment redundancy listed in Table 7-14 must be configured and maintained by software.
7.9.2
Master-Slave Output Clock Phase Alignment
When the T0 DPLL is locked to a selected reference with frequency f, any output clocks derived from T0 with frequency f are phase aligned with the selected reference (if phase build-out is disabled). Any output clocks derived from T0 with frequency greater than f are "falling edge aligned" with the frequency-f output clock. Any output clocks derived from T0 with frequency less than f may or may not be aligned, depending on whether or not their frequencies are integer sub-multiples of f. These statements also apply to output clocks derived from the T4 DPLL. Given this information, if master and slave devices are cross-wired with 19.44MHz clocks, for example, the output clocks at N x 19.44MHz (N = 1, 2, 4, 8, or 16) from the two devices are phase-aligned with one another. Output clocks at lower frequencies (6.48MHz, 1.544MHz, 2.048MHz, 2kHz, 8kHz, etc.) from the two devices would not necessarily be phase aligned. In many systems, lack of phase alignment between the two devices at these clock rates is not an issue. In some systems, however, the 2kHz and/or 8kHz clocks of the two devices must be aligned to avoid framing errors during switchover between master and slave. One way to align the 2kHz and/or 8kHz clocks of the master and slave devices is to configure the slave to lock to a 2kHz or 8kHz output of the master. Another way is to use the SYNC2K input as described in Section 7.9.3.
19-4546; Rev 9; 5/09
55 of 227
DS3100
7.9.3
Master-Slave Frame and Multi-Frame Alignment with the SYNC2K Pin
With this method of aligning the 2kHz and 8kHz clocks of the master and slave devices, both a higher-speed clock (such as 6.48MHz or 19.44MHz) and a frame-sync signal (normally 2kHz) from the master are passed to the slave (and vice versa when their roles are reversed). The higher-speed clock from the master is connected to a regular input clock pin on the slave, such as IC11, while the frame-sync signal from the master is connected to the SYNC2K pin on the slave. The slave locks to the higher-speed clock and samples the frame-sync signal on SYNC2K. The slave then uses the SYNC2K signal to falling-edge align some or all of the output clocks. Only the falling edge of SYNC2K has significance. A 4kHz or 8kHz clock can also be used on SYNC2K without any changes to the register configuration, but only output clocks of 8kHz and above are aligned in this case. Phase build-out should be disabled on the slave (PBOEN = 0 in MCR10), and the higher-speed input clock on the slave must be configured for direct-lock mode (ICR:DIVN = 0 and LOCK8K = 0). Sampling. By default the SYNC2K signal is first sampled on the rising edge of the selected reference. This gives the most margin, given that the SYNC2K signal is falling-edge aligned with the selected reference since both come from the master device. The expected timing of SYNC2K with respect to the sampling clock can be adjusted from 0.5 cycles early to 1 cycle late using the FSCR2:PHASE[1:0] field. Resampling. The SYNC2K signal is then resampled by an internal clock derived from the T0 DPLL. The resampling resolution is a function of the frequency of the selected reference and FSCR2:OCN. When OCN = 0, the resampling resolution is 6.48MHz, which gives the highest sampling margin and also aligns clocks at 6.48MHz and multiples thereof. When OCN = 1, if the selected reference is 19.44MHz then the resampling resolution is 19.44MHz. If the selected reference is 38.88MHz then the resampling resolution is 38.88MHz. The selected reference must be either 19.44MHz or 38.88MHz. SYNC2K Enable. The SYNC2K signal is only allowed to align output clocks if the T0 DPLL is locked and SYNC2K is enabled and qualified. SYNC2K can be enabled automatically or manually. When MCR3:AEFSEN = 1, SYNC2K is enabled automatically when EFSEN = 1 and the T0 DPLL is locked to the input clock specified by FSCR3:SOURCE[3:0]. When AEFSEN = 0, SYNC2K is enabled manually when MCR3:EFSEN = 1 and disabled when EFSEN = 0. In manual mode when EFSEN = 1, FSCR3:SOURCE[3:0] is ignored and SYNC2K is always enabled regardless of which input clock is the selected reference. SYNC2K Qualification. SYNC2K is qualified when it has consistent phase and correct frequency. Specifically, SYNC2K is qualified when its significant edge has been found at exact 2kHz boundaries (when resampled as described above) for 64 SYNC2K cycles in a row. SYNC2K is disqualified when one significant edge is not found at the 2kHz boundary. Output Clock Alignment. When T0 is locked and SYNC2K is enabled and qualified, SYNC2K can be used to falling-edge align the T0-derived output clocks. Output clocks OC10 and OC11 share a 2kHz alignment generator, while the rest of the T0-derived output clocks share a second 2kHz alignment generator. When SYNC2K is not enabled or is not qualified, these 2Hz alignment generators free-run with their existing 2kHz alignments. When SYNC2K is enabled and qualified, the OC10/OC11 2kHz alignment generator is always synchronized by SYNC2K, and therefore OC10 and OC11 are always falling-edge aligned with SYNC2K. When FSCR2:INDEP = 0, the T0 2kHz alignment generator is also synchronized with the OC10/OC11 2kHz alignment generator to falling-edge align all T0-derived output clocks with SYNC2K. When INDEP = 1, the T0 2kHz alignment generator is not synchronized with the OC10/OC11 2kHz alignment generator and continues to free-run with its existing 2kHz alignment. This avoids any disturbance on the T0-derived output clocks when SYNC2K has a change of phase position. Frame Sync Monitor. The frame sync monitor signal OPSTATE:FSMON operates in two modes, depending on the setting of the enable bit (MCR3:EFSEN). When EFSEN = 1 (SYNC2K enabled) the FSMON bit is set when SYNC2K is not qualified and cleared when SYNC2K is qualified. If SYNC2K is disqualified then both 2kHz alignment generators are immediately disconnected from SYNC2K to avoid phase movement on the T0-derived outputs clocks. When OPSTATE:FSMON is set, the latched status bit MSR3:FSMON is also set, which can cause an interrupt if enabled. If SYNC2K immediately stabilizes at a new phase and proper frequency, then it is requalified after 64 2kHz cycles (nominally 32ms). Unless system software intervenes, after SYNC2K is requalified the 2kHz alignment generators will synchronize with SYNC2K's new phase alignment, causing a sudden phase movement on the output clocks. System software can 19-4546; Rev 9; 5/09 56 of 227
DS3100 avoid this sudden phase movement on the output clocks by responding to the FSMON interrupt within the 32ms window with appropriate action, which might include disabling SYNC2K (MCR3:EFSEN = 0) to prevent the resynchronization of the 2kHz alignment generators with SYNC2K, forcing the slave into holdover (MCR1:T0STATE = 010) to avoid affecting the output clocks with any other phase hits, and possibly even disabling the master and promoting the slave to master (see Section 7.9.1) since the 2kHz signal from the master should not have such phase movements. When EFSEN = 0 (SYNC2K disabled) OPSTATE:FSMON is set when the negative edge of the re-sampled SYNC2K signal is outside of the window determined by FSCR3:MONLIM relative to the OC11 negative edge (or positive edge if OC11 is inverted) and clear when within the window. When OPSTATE:FSMON is set, the latched status bit MSR3:FSMON is also set, which can cause an interrupt if enabled. Other Frame Sync Configuration Options. OC10 and OC11 are always produced from the T0 path. Output clocks OC1 to OC7 can also be configured as 2 kHz or 8 kHz outputs, derived from either the T0 path or the T4 path (as specified by the 2K8KSRC bit in FSCR1). If needed, the T4 DPLL can be used as a separate DPLL for the frame sync path by configuring it for a 2kHz input and 2kHz and/or 8 kHz frame sync outputs.
19-4546; Rev 9; 5/09
57 of 227
DS3100
7.10
Multiprotocol BITS Transceivers
The DS3100 has two identical, independent BITS transceivers, each of which support the following synchronization protocols:

DS1 (also configurable for J1) E1 2048kHz (G.703) 6312kHz (G.703)*
*The BITS receivers can receive the 6312kHz signal, but the transmitters do not transmit this protocol because it is easily generated using any of output clocks OC1 through OC7 and an external square-to-sinusoidal network.
The BMCR register description and accompanying footnotes give additional details on these synchronization protocols and the telecom standards with which they comply. Figure 7-7 shows the BITS transceiver block diagram.
Figure 7-7. BITS Transceiver Block Diagram
204.8 MHz master clock MCLK pin
Master Clock PLL
BITS Master Clock
BITS Transceiver (1 of 2)
RTIP pin RRING pin
LIU Receiver
RCLK
DS1/E1 Framer
(SSM extraction) + RSYNC RMFSYNC
RCLK pin RSER pin to IC1 - IC14 input muxes ROUT pin
64k/8k Decoder Remote Loopback Analog Loopback Local Loopback
Transmit Clock
DS1/E1 Formatter
CLOCK + DATA - DATA (SSM insertion) +
TMFSYNC
Tx Clock Mux
TSYNC
from OC1 - OC9 output clocks TIN pin TCLK pin TOUT pin TSER pin
TTIP pin TRING pin
LIU Transmitter
64k/8k Encoder
THZE pin
Note: The DS3100 BITS transceivers are full-featured DS1/E1 LIUs and framers. To keep configuration as simple as possible, only the features most commonly used for clock synchronization applications are made visible in this data sheet. If your application requires LIU or framer features not described in this document, contact the factory at www.maxim-ic.com/support for additional information.
19-4546; Rev 9; 5/09
58 of 227
DS3100
7.10.1
Master Clock Connections
See Figure 7-7 and Figure 7-8. The master clock PLL block produces two clocks: (1) a 16X line rate oversampling clock for the receiver, and (2) the BITS master clock, which can optionally be used by the transmitter. Both of these clocks are made from the same BITS transceiver master clock. There are two possible sources for the BITS master clock: the 204.8MHz master clock and the MCLK input pin. Normally BCCR3:MCLKS is set to 0, to select the 204.8MHz master clock (see Section 7.3) divided by 100. The resulting 2.048MHz clock can be used as-is for E1 and 2048kHz synchronization or fed into a 2.048MHz to 1.544MHz frequency converter PLL for DS1 synchronization. For special applications, MCLKS can be set to 1 to source the BITS transceiver master clock from the MCLK pin. When MCLKS = 1, the signal on the MCLK pin is divided by 1, 2, 4, or 8 (as specified by BCCR5:MPS[1:0]) and optionally passed through the 2.048MHz to 1.544MHz frequency-converter PLL (as specified by BCCR3:MCLKFC). For any BITS receiver mode, the signal on the MCLK pin can be 1, 2, 4, or 8 times 2.048MHz. For DS1 mode only, MCLK can be 1, 2, 4, or 8 times 1.544MHz. When MCLKS = 0, the MCLK pin is ignored and should be wired high or low.
Figure 7-8. BITS Transceiver Master Clock PLL Block Diagram
Master CLock PLL
204.8 MHz master clock MCLK pin Divide by 100
0 1
Prescaler: divide by 1, 2, 4 or 8
BCCR5:MPS[1:0]
0
2.048 MHz to 1.544 MHz PLL
BITS master clock
1
BCCR3:MCLKS
BCCR3:MCLKFC
x16 Multiplier PLL
to LIU receiver clock and data recovery
7.10.2
Receiver Clock Connections
See Figure 7-7. The BITS receiver typically forwards its recovered clock to one of input clocks IC1 through IC14. The RCLKD field in BCCR2 specifies the destination. The input clock that is selected as the destination considers the BITS receiver to be its clock source and ignores the signal at its own input pin. For input clocks IC1, IC2, IC5, and IC6, the signal from the BITS receiver is inserted after the AMI/LVDS/LVPECL input logic. For DS1, E1 and 2048kHz BITS receiver modes, typically the recovered clock is forwarded to one of the ICx input clocks by configuring BCCR2:RCLKD to specify the input clock and configuring the input clock for 1544kHz or 2048kHz as described in Section 7.4.2. The recovered clock can be output on the RCLK pin if needed by setting BCCR3:RCEN = 1 to enable the pin. Optionally the frame sync of the incoming DS1/E1 signal can be forwarded to one of the ICx input clocks by configuring BCCR2:RSYNCD to specify the input clock and configuring the input clock for 8kHz as described in Section 7.4.2. Also, the DS1/E1 frame sync or multiframe sync can be output on the ROUT pin by setting BCCR3:ROUTS appropriately and setting BCCR3:ROEN = 1 to enable the pin. The frame sync signal is normally low and pulses high for one RCLK cycle during the framing bit (DS1) or the first FAS bit (E1). The multiframe sync signal is normally low and pulses high for one RCLK cycle on the first bit of the multiframe. In E1 modes, the type of multiframe sync (CAS or CRC-4) can be specified in BRCR5:RMFS. The polarity of RCLK and ROUT can be inverted by setting BCCR3:RCINV and ROINV, respectively. Since the BITS clock and frame sync signals are rising edge oriented and the DPLL clocks are falling edge oriented, all clock and sync signals from the BITS receiver are inverted before being used by the DPLL. When the DPLL is locked to a clock or sync signal from a BITS receiver, the DPLL output clocks are falling-edge aligned with the rising edge of the input signal. If the T0 DPLL is locked to a frame sync signal from a BITS receiver, the falling 19-4546; Rev 9; 5/09 59 of 227
DS3100 edge of the OC10 frame sync signal is aligned to the rising edge of the RSYNC signal, and if the OC10 pin is set to pulse mode, the OC10 pulse is closely aligned with the RSYNC pulse. For 6312kHz BITS receiver mode, the recovered clock can be forwarded to one of the ICx input clocks by configuring BCCR2:RCLKD to specify the input clock and configuring the input clock for 6312kHz using the DIVN locking mode with DIVN = 788. Optionally the recovered 6312kHz clock can be output on the RCLK pin by setting BCCR3:RCEN = 1 to enable the pin. If both BITS receivers are used simultaneously, they should specify different ICx input clocks as destinations in their RCLKD and RSYNCD fields. If any two or more of these fields specify identical destinations then RCLK from BITS receiver 1 takes precedence, followed by RSYNC from BITS receiver 1, then RCLK from BITS receiver 2 then RSYNC from BITS receiver 2. If a BITS receiver detects a defect (e.g., BPVs, EXZs, LOS, AIS, OOF) in the incoming signal, two methods can be used to invalidate the ICx input clock(s) to which the BITS receiver is connected. The first method is to poll the BITS receiver status registers, or react to interrupt requests from those registers, and, if a significant defect is discovered, invalidate the input clock(s) by clearing the corresponding bit in the VALCR1 and VALCR2 registers. The second method is to configure the device to automatically react when defects are detected. For LOS, AIS and OOF, if the corresponding enable bits are set in BCCR5, then the associated ICx input clock(s) are automatically marked invalid in the VALSR registers when defects occur. For BPVs and excessive zeros (EXZs), if the corresponding enable bits are set in BCCR5, then these defects are considered irregularities by the activity monitors of the associated ICx input clock(s). See Section 7.5.2 for more information on the activity monitors. Note that RCLK and RSYNC are automatically squelched by the BITS receiver during LOS. If either RCLK or RSYNC happens to be the selected reference when LOS occurs, the fast activity monitor in the DPLL (Section 7.5.3) detects the lack of transitions caused by the squelching within two cycles and causes the DPLL to enter miniholdover mode until the selected reference returns or is invalidated by the DPLL input clock monitors. If ultra-fast switching mode is enabled (MCR10:UFSW = 1, see Section 7.6.4), then the fast activity monitor immediately invalidates the clock and switches to a new reference or to holdover mode if no other input clock is valid. RCLK is squelched in the paths to the RCLK output pin and the ICx input monitoring circuitry, but it is not squelched in the receive framer clock tree. Figure 10-4 and Table 10-11 show the timing relationships among RCLK, ROUT, and RSER.
Figure 7-9. BITS Transmitter Clock Mux Block Diagram
BCCR1:TCLKS[3:0]
Tx Clock Mux
TIN output clocks OC1 - OC10 RCLK line-rate clock from Master Clock PLL
TCLK
BCCR1:TSYNCS[3:0]
Align
Counter
Clk BCCR4:TMFS Align
TSYNC
Counter
Clk
TMFSYNC
19-4546; Rev 9; 5/09
60 of 227
DS3100
7.10.3
Transmitter Clock Connections
See Figure 7-7 and Figure 7-9. The BCCR1:TCLKS field specifies the source for the BITS transmitter clock (TCLK). Typically TCLK is sourced from one of DPLL output clocks OC1-OC7 or OC9 (configured for 1544kHz or 2048kHz as described in Section 7.8.2). In DS1 and E1 modes the BITS transmitter also requires a frame sync and/or multiframe sync signal to specify the start of the frame or multiframe. The frame sync signal is normally low and pulses high for one TCLK cycle on the first bit of the frame. The multiframe sync signal is normally low and pulses high for one TCLK cycle on the first bit of the multiframe. The frame sync (TSYNC) signal is created in the Tx Clock Mux block by a counter circuit that outputs a signal that is normally low and pulses high for one TCLK cycle out of every 193 (DS1 mode) or 256 (E1 mode). The multiframe sync (TMFSYNC) signal is then created by another counter circuit that outputs a signal that is normally low and pulses high coincident with one TSYNC pulse out of every 12 (DS1 SF mode), 24 (DS1 ESF mode, or 16 (E1 mode). In many applications the DS1/E1 frame sync and multiframe sync signals are not required to be aligned with any other signal (other than rising-edge aligned to TCLK and each other), and therefore, by default, the TSYNC and TMFSYNC counter circuits are allowed to free-run without being aligned by an input signal (BCCR1:TSYNCS = 1111, BCCR4:TMFS = 0). For applications that require it, the leading edge of the TSYNC pulse can be aligned with a clock edge from one of DPLL output clocks OC1-OC7 or OC10 or the BITS transmitter's TIN input pin. The BCCR1:TSYNCS field specifies the source of the clock used to align TSYNC. For proper operation, the TSYNC source and the TCLK source must be frequency locked. Because the TSYNC counter circuit free-runs when not being actively aligned by an input signal, the TSYNC source clock can pulse just one time to establish TSYNC alignment or it can be a steady clock with a frequency of 8kHz or any integer divider of 8kHz. Duty cycle is not important for the TSYNC source clock. For applications that require it, the TMFSYNC pulse can be aligned with a clock edge from the BITS transmitter's TIN input pin by setting BCCR4:TMFS = 1. Because the TMFSYNC counter circuit free-runs when not being actively aligned by an input signal, the TMFSYNC source clock can pulse just one time to establish TMFSYNC alignment or it can be a steady clock with a frequency of 8kHz / X (where X is 12 for DS1 SF mode, 24 for DS1 ESF mode, and 16 for E1 mode) or any integer divider of 8kHz / X. When the TMFSYNC pulse is aligned by a clock edge on the TIN pin, the TSYNC signal is automatically aligned as well to maintain frame/multiframe alignment (see the OR gate in Figure 7-9). Duty cycle is not important for the TMFSYNC source clock. When a DPLL output clock is selected as a clock source for TCLK or TSYNC, the output clock signal is forwarded to the BITS transmitter without being affected by any configuration settings that disable, invert, or convert-to-pulse the signal output on the OCx output clock pin. Because the DPLL output clocks are falling-edge oriented and the BITS transmitter clock and frame sync signals are necessarily rising edge oriented, the DPLL clock signals specified by BCCR1:TCLKS and BCCR1:TSYNCS are inverted between the DPLL and the BITS transmitter so that the falling edge(s) of the DPLL output clock(s) are aligned to the rising edges of the TCLK and TSYNC (and TMFSYNC) signals. When OC10 is selected as the alignment signal for TSYNC and configured in pulse mode, the leading and trailing edges of the OC10 pulse are aligned with the leading and trailing edges of the TSYNC signal in the BITS transmitter. The TCLK signal can be output on the TCLK pin by setting BCCR4:TCEN = 1 to enable the pin. Optionally, the TSYNC signal or the TMFSYNC signal can be output on the TOUT pin by specifying the signal with BCCR4:TOUTS and setting BCCR4:TOEN = 1 to enable the pin. The polarity of the TIN, TCLK and TOUT pins can be inverted by setting BCCR4:TIINV, TCINV and TOINV, respectively. As can be seen from Figure 7-9, the typical setups described above are just a few of the possible BITS transmitter clock configurations. As the figure shows, both the recovered clock from the BITS receiver (RCLK) and the line rate clock from the master clock PLL are possible clock sources for the BITS transmitter TCLK. Using an OCx output pin and the TIN input pin, the BITS transmitter clock signal can be externally filtered or otherwise adjusted before being sent out through the BITS transmitter. If needed, the TCLK and TOUT output pins can be enabled--by setting TCEN = 1 and TOEN = 1, respectively, in BCCR4--to pass key BITS transceiver clocks to external circuitry. Finally, the data content of the DS1 or E1 frame can be sourced from the TSER pin if needed. Figure 10-5 and Table 10-12 show the timing relationships among TCLK, TIN, TOUT, and TSER.
19-4546; Rev 9; 5/09
61 of 227
DS3100
7.10.4
Line Interface Unit
The line interface unit (LIU) contains the receiver, which recovers clock and data from the inbound cable, and the transmitter, which wave-shapes and drives the signal onto the outbound cable. These sections are controlled by the line interface control registers, BLCR1 through BLCR4. The receiver has a usable receive sensitivity of 0dB to -43dB for E1 and 0dB to -36dB for DS1, which allows the device to operate on 0.63mm (22AWG) cables up to 2.5 km (E1) and 6000 feet (DS1) in length. The transmitter line driver can handle both CEPT 30/ISDN-PRI lines for E1 and long-haul (CSU) or short-haul (DSX-1) lines for DS1. The receiver and transmitter can switch among the supported synchronization signal types without changing external components. Figure 7-10 shows the minimum set of external components required. Both the receiver and the transmitter can adjust their termination impedance to provide high return loss characteristics for 75, 100, 110, and 120 lines. Other components may be added to this configuration in order to meet safety and network protection requirements, if required.
Figure 7-10. BITS Transceiver External Components
Internal Receiver Termination Enabled
1uF
560 pF
TTIP TTIP
VDD VDD
0.1uF
1uF
10uF
0.1uF
1uF
10uF
3.3V Power Plane 1.8V Power Plane
2:1
TRING TRING RTIP
VDD
0.1uF
1uF
10uF
VSS VSS Ground Plane
RRING
1:1
VSS
Note: The 1uF capacitor is mandatory for 2048kHz mode and optional for DS1 and E1 modes.
Internal Receiver Termination Disabled
1uF
560 pF
TTIP TTIP
VDD VDD
0.1uF
1uF
10uF
0.1uF
1uF
10uF
3.3V Power Plane 1.8V Power Plane
2:1
TRING TRING RTIP
60.4 (1%) 60.4 (1%) 0.1 uF
VDD
0.1uF
1uF
10uF
VSS VSS Ground Plane
RRING
1:1
VSS
Note: The 1uF capacitor is mandatory for 2048kHz mode and optional for DS1 and E1 modes.
19-4546; Rev 9; 5/09
62 of 227
DS3100 7.10.4.1 7.10.4.1.1 Receiver Interfacing to the Line
The receiver can be transformer-coupled or capacitor-coupled to the line. Typically, the receiver interfaces to the incoming coaxial cable or twisted-pair wiring through a 1:1 isolation transformer. Figure 7-10 shows the arrangement of the transformer with either internal termination or external termination. For internal termination, set BLCR3:RION = 1 and set BLCR3:RIMP[1:0] to specify the termination impedance. For external termination, set BLCR3:RION = 0 and use external termination resistors as shown in Figure 7-10. Table 7-15 specifies the required characteristics of the transformer. 7.10.4.1.2 Receive Sensitivity Receive sensitivity can be adjusted in DS1, E1, and 2048kHz modes using BLCR3:RSMS[1:0]. In 6312kHz mode, receive sensitivity is fixed at approximately -24dB. 7.10.4.1.3 Receive Level Indicator The signal strength at RTIP/RRING is reported in 2.5dB increments in BLIR2:RL[3:0]. This feature is helpful when troubleshooting line performance problems. 7.10.4.1.4 Optional Monitor Mode The receiver can be used in monitoring applications, which typically have flat losses from the use of series resistors. In these applications a pre-amp stage in the receiver can be configured to apply 14dB, 20dB, 26dB, or 32dB of flat gain to compensate for the resistive losses. The monitor mode preamp is enabled by setting BLCR3:RMONEN = 1 and configured by BLCR3:RSMS[1:0]. 7.10.4.1.5 Clock and Data Recovery The BITS receiver has an active filter that reconstructs the received analog signal for the nonlinear losses that occur in transmission. The BITS master clock (Section 7.10.1) is multiplied by 16 and used as the master clock for the APLL used in the receiver to recover clock and data. The receiver has excellent jitter tolerance as shown in Figure 7-11 and Figure 7-12.
Figure 7-11. Jitter Tolerance, DS1 Mode
1K DS3100 Jitter Tolerance TR 62411 (Dec. 90) 10 ITU-T G.823 1
UNIT INTERVALS (UIpp)
100
0.1
1
10
100 1k FREQUENCY (Hz)
10k
100k
19-4546; Rev 9; 5/09
63 of 227
DS3100
Figure 7-12. Jitter Tolerance, E1 and 2048kHz Modes
1k DS3100 Jitter Tolerance
40
UNIT INTERVALS (UIpp)
100
10
1.5
1
Minimum Tolerance Level as per ITU G.823 1
20 2.4k 18k
0.2
0.1
10
100 1k FREQUENCY (Hz)
10k
100k
7.10.4.1.6
Loss-of-Signal Detection
In DS1 mode, LOS is declared when no pulses are detected (i.e., when the signal level is 6dB below the receive sensitivity level set by BLCR3:RSMS[1:0]) in a window of 192 consecutive pulse intervals. When LOS occurs, the receiver sets the real-time LOS status bit in BLIR1 and the latched LOS status bit in BLSR1. BLSR1:LOS in turn can cause and interrupt request on the INTREQ pin if enabled by BLIER1:LOS. LOS is cleared when 24 or more pulses are detected (amplitude greater than receive sensitivity minus 4dB) in a 192-bit period (pulse density above 12.5%) and there are no occurrences of 100 or more consecutive zeros during that period. This algorithm meets the requirements of ANSI T1.231. For example, if receive sensitivity is set at 18dB below nominal (BLCR3:RSMS[1:0], the LOS set threshold is 24dB below nominal, and the LOS clear threshold is 22dB below nominal. In E1 and 2048kHz modes, if BLCR1:LCS = 0 the receiver is configured for ITU G.775 LOS detection. When configured in this manner, LOS is declared when no pulses are detected (i.e., when the signal level is 6dB below the receive sensitivity level set by BLCR3:RSMS[1:0]) in a window of 255 consecutive pulse intervals. When LOS occurs, the receiver sets the real-time LOS status bit in BLIR1 and the latched LOS status bit in BLSR1. BLSR1:LOS in turn can cause and interrupt request on the INTREQ pin if enabled by BLIER1:LOS. LOS is cleared when at least 32 pulses are detected (amplitude greater than receive sensitivity minus 4dB) in a window of 255 consecutive pulse intervals. In E1 and 2048kHz modes, if BLCR1:LCS = 1 the receiver is configured for ETSI 300 233 LOS detection. When configured in this manner, LOS is declared when no pulses are detected (i.e., when the signal level is 6dB below the receive sensitivity level set by BLCR3:RSMS[1:0]) in a window of 2048 consecutive pulse intervals. When LOS occurs, the receiver sets the real-time LOS status bit in BLIR1 and the latched LOS status bit in BLSR1. BLSR1:LOS in turn can cause and interrupt request on the INTREQ pin if enabled by BLIER1:LOS. LOS is cleared when at least one pulse is detected (amplitude greater than receive sensitivity minus 4dB) in a window of 255 consecutive pulse intervals. In 6312kHz mode, LOS is declared when the signal level is below -24dBm for a 32s period. 7.10.4.1.7 Receiver Power-Down The receiver can be powered down to reduce power consumption by setting BLCR4:RPD = 1. When the receiver is powered down, all digital outputs from the receiver are held low, and RTIP and RRING become high impedance.
19-4546; Rev 9; 5/09
64 of 227
DS3100 7.10.4.2 7.10.4.2.1 Transmitter Waveshaping
The BITS LIU transmitter uses a phase-locked loop along with a precision digital-to-analog converter (DAC) to create the waveforms that are transmitted onto the outbound cable. The waveforms meet the latest ANSI, ETSI, ITU and Telcordia specifications (see Figure 7-13, Figure 7-14, and Figure 7-15). The BMCR:TMODE[1:0] field specifies the waveform to be generated, along with the line build out field in BLCR2:LBO[2:0], if applicable. Due to the nature of its design, the transmitter adds very little jitter (less than 0.005UIP-P broadband from 10Hz to 100kHz) to the transmit signal. Also, the waveforms created are independent of the duty cycle of TCLK. 7.10.4.2.2 Line Build-Out The transmitter line driver can handle both CEPT 30/ISDN-PRI lines for E1 and long-haul (CSU) or short-haul (DSX-1) lines for DS1. The LBO[2:0] field in BLCR2 specifies the line build-out for DS1 and E1. 7.10.4.2.3 Line Driver Enable/Disable When the THZE pin is high or when BLCR4:TE = 0, the transmitter line driver is disabled, and TTIP/TRING are put in a high-impedance state. When the THZE pin is low and BLCR4:TE = 1, the line driver is enabled. 7.10.4.2.4 Interfacing to the Line The transmitter is transformer-coupled to the line. Typically, the transmitter interfaces to the outgoing coaxial cable or twisted-pair wiring through a 1:2 isolation transformer. Figure 7-10 shows the arrangement of the transformer with respect to the TTIP and TRING pins. On the DS3100 the transmitter termination is always internal. Set BLCR2:TION = 1 and set BLCR2:TIMP[1:0] to specify the termination impedance. Table 7-15 specifies the required characteristics of the transformer. 7.10.4.2.5 AIS Generation When BLCR4:TAIS = 1, the transmitter generates AIS (unframed all ones) using the BITS master clock as the timing reference. 7.10.4.2.6 Short-Circuit Detector The BITS transmitter has an automatic short-circuit detector that activates when the short-circuit resistance is approximately 25 or less. BLIR1:SC provides a real-time indication of when the short-circuit limit has been exceeded. Latched status bits BLSR1:SC and SCC are set when BLIR1:SC changes state from low-to-high and high-to-low, respectively. These latched status bits can cause an interrupt request if enabled by the corresponding bits in BLIER1. The short-circuit detector is disabled for CSU modes (i.e., when BLCR2:LBO[2:0] = 101, 110, or 111). 7.10.4.2.7 Open-Circuit Detector The BITS transmitter can also detect when TTIP and TRING are open circuited. BLIR1:OC provides a real-time indication of when the open-circuit limit has been exceeded. Latched status bits BLSR1:OC and OCC are set when BLIR1:OC changes state from low-to-high and high-to-low, respectively. These latched status bits can cause an interrupt request if enabled by the corresponding bits in BLIER1. The open-circuit detector is disabled for CSU modes (i.e., when BLCR2:LBO[2:0] = 101, 110, or 111). 7.10.4.2.8 Transmitter Power-Down The transmitter can be powered down to reduce power consumption by setting BLCR4:TPD = 1. When the transmitter is powered down, TTIP and TRING are high impedance.
19-4546; Rev 9; 5/09
65 of 227
DS3100
Figure 7-13. Transmit Pulse Template, DS1 Mode
1.2 1.1 1.0 0.9 0.8 0.7 NORMALIZED AMPLITUDE 0.6 0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 -0.5 -500 -400 -300 -200 -100 0 100 200 300 400 500 600 700
T1.102/87, T1.403, CB 119 (Oct. 79), & I.431 Template
MAXIMUM CURVE UI Time Amp. -0.77 -0.39 -0.27 -0.27 -0.12 0.00 0.27 0.35 0.93 1.16 -500 -255 -175 -175 -75 0 175 225 600 750 0.05 0.05 0.80 1.15 1.15 1.05 1.05 -0.07 0.05 0.05 MINIMUM CURVE UI Time Amp. -0.77 -0.23 -0.23 -0.15 0.00 0.15 0.23 0.23 0.46 0.66 0.93 1.16 -500 -150 -150 -100 0 100 150 150 300 430 600 750 -0.05 -0.05 0.50 0.95 0.95 0.90 0.50 -0.45 -0.45 -0.20 -0.05 -0.05
TIME (ns)
Figure 7-14. Transmit Pulse Template, E1 Mode
1.2 1.1 1.0
(in 75 ohm systems, 1.0 on the scale = 2.37Vpeak in 120 ohm systems, 1.0 on the scale = 3.00Vpeak) 269ns
0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2
-250 -200 -150 -100 -50 0 50 100 150 200 250 219ns 194ns
SCALED AMPLITUDE
G.703 Template
TIME (ns)
19-4546; Rev 9; 5/09
66 of 227
DS3100
Figure 7-15. Transmit Pulse Template, 2048kHz Mode
TT 30 30 TT 30 30 TT 30 30 +V
+V1
75 Ohm Coaxial Cable V = 1.5V V1 = 0.75V
0 120 Ohm Symmetrical Pair V = 1.9V V1 = 1.0V -V1
-V T 4 T 4 T Shaded area in which signal should be montonic T Average period of synchronizing signal T 4 T 4
7.10.4.3
LIU Loopbacks
The BITS LIU provides three loopbacks for diagnostic purposes: analog loopback, local loopback, and remote loopback. See Figure 7-7. These loopback are enabled by the ALB, LLB, and RLB bits in BLCR4. 7.10.4.4 Component Specifications
Table 7-15. Transformer Specifications
SPECIFICATION Turns Ratio Primary Inductance Leakage Inductance Intertwining Capacitance Transmit Transformer DC Resistance Receive Transformer DC Resistance Isolation Voltage Primary (Device Side) Secondary Primary (Device Side) Secondary Receiver Transmitter RECOMMENDED VALUE 1:1 or 2:1 (2%) 1:2 (2%) 600H minimum 1.0H maximum 40pF maximum 1.2 maximum 1.2 maximum 1.2 maximum 1.2 maximum 1500 VRMS (min)
Note: Recommended transformers include the Pulse Engineering PE-68678 (0C to +70C) and T1094 (-40C to +85C), both of which are surface-mount dual transformers (1:1 and 1:2).
19-4546; Rev 9; 5/09
67 of 227
DS3100
7.10.5
DS1 Synchronization Interface
Each BITS transceiver receives and transmits standards-compliant DS1 synchronization signals. As a configuration option of DS1, the BITS transceivers can also be configured for the Japanese J1 interface. 7.10.5.1 Receive Framer In the receive direction, the BITS transceiver recovers clock and data, does B8ZS decoding, finds frame alignment, and extracts incoming SSM messages. Each BITS receiver can be configured for DS1 mode by following these steps: 1) Set the overall mode of the receiver to DS1 by setting BMCR:RMODE = 00. 2) Configure and enable the DS1/E1 framer in the BRMMR register as follows: (a) toggle RRST high then low, (b) set RT1E1 = 0 to configure the framer for DS1 mode, (c) set registers BRCR1, BRCR2 and BRCR5 as needed, (d) set REN = 1 to enable the framer, and (e) set RID = 1 to start the framer. 3) Configure and enable the LIU receiver as described in Section 7.10.4.1. Registers BRCR1, BRCR2 and BRCR5 configure the receive framer in DS1 mode. BRCR1:RFM specifies superframe or extended superframe mode. BRCR1:RB8ZS enables B8ZS decoding. The receive framer can be configured for J1 operation by setting BRCR1:RJC = 1 and BRCR2:RSFRAI = 1. Status register BRIR1 has realtime status bits to indicate the presence of RAI, AIS, LOS and OOF conditions, while status register BRSR1 has latched versions of these same status bits. (See Table 7-16 for alarm set and clear criteria.) The onset or clearing of any of these events can cause an interrupt request on the INTREQ pin if enabled to do so by the corresponding enable bits in the BRIER1 register. Status registers BRSR2 and BRSR4 provide additional status information. The entire received DS1 data stream is available on the RSER pin for additional processing by external hardware, if needed. RSER is updated on the rising edge of the RCLK pin by default, but this can be changed to the falling edge by setting BCCR3:RCINV = 1.
Table 7-16. DS1 Alarm Criteria
ALARM AIS (Note 1) SF Bit-2 Mode (Note 2) RAI SF 12th F-Bit Mode (Note 2) ESF Mode SET CRITERIA Four or fewer 0s are received during a 3ms window. Bit 2 is set to zero in at least 254 of 256 consecutive channel time slots. The 12th framing bit is set to 1 for two consecutive occurrences. 16 consecutive patterns of 00FFh appear in the FDL. 192 consecutive zeros received Two or more errored-frame bits out of every four, five, or six frame bits. (Configured by BRCR2:OOFC[1:0].) CLEAR CRITERIA Five or more 0s are received during a 3 ms window. Bit 2 is set to zero in less than 254 of 256 consecutive channel time slots. The 12th framing bit is set to 0 for two consecutive occurrences. 14 or fewer patterns of 00FFh appear in 16 consecutive opportunities in the FDL. 14 or more ones received out of 112 possible bit positions, starting with the first one received. Fewer than two errored-frame bits out of every four, five, or six frame bits. (Configured by BRCR2:OOFC{1:0].)
-3
LOS
OOF
Note 1:
Note 2:
AIS is an unframed all-ones signal. AIS detectors should be able to operate properly in the presence of a 10 error rate and must not declare AIS in the presence of a framed all-ones signal. The BITS transceiver block has been designed to achieve this performance. In SF framing mode, the RAI type is configured by the RSFRAI bit in the BRCR2 register. The method of indicating RAI using the 12th F-Bit in SF mode is also known as Japanese Yellow Alarm.
19-4546; Rev 9; 5/09
68 of 227
DS3100 7.10.5.2 Transmit Formatter
In the transmit direction, the BITS transceiver formats the outgoing data stream, inserts SSM messages, does B8ZS encoding, and drives the outgoing cable with standards-compliant waveshapes. Each BITS transmitter can be configured for DS1 mode by following these steps: 1) Set the overall mode of the transmitter to DS1 by setting BMCR:TMODE = 00. 2) Configure and enable the DS1/E1 framer in the BTMMR register as follows: (a) toggle TRST high then low, (b) set TT1E1 = 0 to configure the framer for DS1 mode, (c) set registers BTCR1, BTCR2, and BTCR3 as needed, (d) set TEN = 1 to enable the framer, and (e) set TID = 1 to start the framer. 3) Configure and enable the LIU transmitter as described in Section 7.10.4.2. Registers BTCR1, BTCR2, and BTCR3 configure the transmit formatter in DS1 mode. BTCR3:TFM specifies superframe or extended superframe mode. BTCR1:TB8ZS enables B8ZS encoding. The transmit formatter can be configured for J1 operation by setting BTCR1:TJC = 1 and BTCR2:TSFRAI = 1. In register BTCR1, fields TAIS and TRAI control the transmission of AIS and RAI signals, respectively. Status register BTSR1 provides latched status information from the transmit formatter. Payload is sourced from the TSER pin. GR-1244-CORE Section 2.4 recommends an all-ones payload, which can be achieved be wiring TSER high. TSER is sampled on the falling edge of the TCLK pin by default, but this can be changed to the rising edge by setting BCCR4:TCINV = 1. 7.10.5.3 DS1 SSM Extraction and Insertion
Although synchronization DS1s can have superframe (SF) or extended superframe (ESF) framing format, only DS1s in ESF format can carry SSMs. Therefore, BTCR3:TFM must be set for ESF mode to support SSMs in outgoing derived DS1s, while BRCR1:RFM must be set for ESF mode to support SSMs in incoming DS1s from the timing signal generator. In an ESF DS1, SSMs are transmitted in the data link as a bit-oriented code (BOC) (T1.403: "bit-patterned message"). SSMs have the format 0xxxxxx011111111 (right-to-left), where xxxxxx are the six information bits of the message. ANSI standard T1.101 lists the SSM codes carried by DS1 timing signals. On the receive side, the BITS transceivers each have a dedicated bit-oriented code (BOC) detector, which is always enabled. When the incoming SSM changes, the BOC detector validates it according to the criteria specified by the RBF field in BRBCR) before declaring it valid. Once validated, the six information bits of the new SSM are written to the lower six bits of the BRBOC register, and the BD status bit in BRSR4 is set to indicate that a new SSM has arrived. The procedure to receive SSMs is as follows: 1) Set the validation filter in BRBCR:RBF. 2) (Optional) Enable the BD status bit to cause interrupt requests by setting BD = 1 in BRIER4. 3) Wait for an interrupt request or poll BRSR4 for BD = 1. 4) Read the SSM from the lower six bits of the BRBOC register. If the incoming DS1 signal no longer has a valid BOC, the BOC detector waits for the number of message bits specified by BRBCR:RBD[1:0] before declaring that a valid BOC is no longer detected by setting BRSR4:BC = 1. The BC field can cause an interrupt request if BRIER4:BC = 1. On the transmit side, the BITS transceivers each have a dedicated BOC generator. When SBOC = 1 in BTBCR the BOC generator uses the lower six bits of the BTBOC register to continually insert SSMs into the ESF data link. BTCR1:TFPT must be set to zero when SBOC = 1. The procedure to transmit SSMs is as follows: 1) Write the 6 information bits of the SSM to the BTBOC register. 2) Set SBOC = 1 in BTBCR.
19-4546; Rev 9; 5/09
69 of 227
DS3100
7.10.6
7.10.6.1
E1 Synchronization Interface
Receive Framer
Each BITS transceiver receives and transmits standards-compliant E1 synchronization signals. In the receive direction, the BITS transceiver recovers clock and data, does HDB3 decoding, finds frame alignment, and extracts incoming SSM messages. Each BITS receiver can be configured for E1 mode by following these steps: 1) Set the overall mode of the receiver to E1 by setting BMCR:RMODE = 01. 2) Configure and enable the DS1/E1 framer in the BRMMR register as follows: (a) toggle RRST high then low, (b) set RT1E1 = 1 to configure the framer for E1 mode, (c) set registers BRCR3, BRCR4 and BRCR5 as needed, (d) set REN = 1 to enable the framer, and (e) set RID = 1 to start the framer. 3) Configure and enable the LIU receiver as described in Section 7.10.4.1. Registers BRCR3, BRCR4 and BRCR5 configure the receive framer in E1 mode. BRCR3:RCRC4 enables CRC-4 framing mode. BRCR3:RHDB3 enables HDB3 decoding. Status register BRIR1 has real-time status bits to indicate the presence of RAI, AIS, LOS and OOF conditions, while status register BRSR1 has latched versions of these same status bits. (See Table 7-16 for alarm set and clear criteria.) The onset or clearing of any of these events can cause an interrupt request on the INTREQ pin if enabled to do so by the corresponding enable bits in the BRIER1 register. Additional FAS/CAS/CRC-4 frame sync status information is available in register BRSR3. See Table 7-18 for E1 sync and resync criteria. The entire received E1 data stream is available on the RSER pin for additional processing by external hardware, if needed. RSER is updated on the rising edge of the RCLK pin by default, but this can be changed to the falling edge by setting BCCR3:RCINV = 1.
Table 7-17. E1 Alarm Criteria
ALARM AIS RAI LOS OOF SET CRITERIA Fewer than three zeros in two frames (512 bits) Bit 3 of non-FAS frame set to one three consecutive occasions 255 or 2048 consecutive zeros received (determined by BRCR4:RLOSC) See Table 7-18. CLEAR CRITERIA Three or more zeros in two frames (512 bits) Bit 3 of non-FAS frame set to zero for three consecutive occasions At least 32 ones received in 255 bit times See Table 7-18. ITU SPEC O.162 1.6.1.2 O.162 2.1.4 G.775 4.2 --
Table 7-18. E1 Sync and Resync Criteria
FRAME OR MULTIFRAME TYPE FAS SYNC CRITERIA FAS present in frames N and N+2 and FAS not present in frame N+1. Two valid multiframe alignment words found within 8ms. Valid multiframe alignment word found. RESYNC CRITERIA If BRCR3:FRC = 0, three consecutive incorrect FAS. If BRCR3:FRC = 1, three consecutive incorrect FAS or three consecutive incorrect bit 2 of non-FAS frame 915 or more errored CRC-4 blocks out of 1000. Two consecutive multiframe alignment words received in error or, for a period of one multiframe, all the bits in time slot 16 are zero. ITU SPEC G.706 4.1.1 4.1.2 G.706 4.2 and 4.3.2 G.732 5.2
CRC-4 CAS
19-4546; Rev 9; 5/09
70 of 227
DS3100 7.10.6.2 Transmit Formatter
In the transmit direction, the BITS transceiver formats the outgoing data stream, inserts SSM messages, does HDB3 encoding, and drives the outgoing cable with standards-compliant waveshapes. Each BITS transmitter can be configured for E1 mode by following these steps: 1) Set the overall mode of the receiver to E1 by setting BMCR:TMODE = 01. 2) Configure and enable the DS1/E1 framer in the BTMMR register as follows: (a) toggle TRST high then low, (b) set TT1E1 = 1 to configure the framer for E1 mode, (c) set registers BTCR3 and BTCR4 as needed, (d) set TEN = 1 to enable the framer, and (e) set TID = 1 to start the framer. 3) Configure and enable the LIU transmitter as described in Section 7.10.4.2. 4) Configure BTAF=1Bh and BTNAF=40h to set up the transmit E1 framing overhead. Registers BTCR3 and BTCR4 configure the transmit formatter in E1 mode. BTCR4:TCRC4 enables CRC-4 framing mode. BTCR4:THDB3 enables HDB3 encoding. BTCR4:TAIS controls the transmission of the AIS signal. Status register BTSR1 provides latched status information from the transmit formatter. Payload, and optionally overhead bits, can be sourced on the TSER pin from external hardware, if needed. TSER is sampled on the falling edge of the TCLK pin by default, but this can be changed to the rising edge by setting BCCR4:TCINV = 1. 7.10.6.3 Basic FAS/Si/RAI/Sa Insertion and Extraction The most basic E1 framing is a double frame consisting of an align frame followed by a non-align frame. The align frame is the E1 frame containing the frame alignment signal (FAS) while the non-align frame is the E1 frame that does not contain the FAS. On the receive side, the BRAF and BRNAF registers always report the contents of the first eight bits of the align frame and the non-align frame, respectively. Both registers are updated at the start of the align frame, which is indicated by the RAF status bit in BRSR3. After RAF is set to 1, software has 250s to read the registers before they are overwritten by the bits from the next double-frame. On the transmit side, the BTAF and BTNAF registers can source the first eight bits of the align frame and the nonalign frame, respectively. Data is sampled from these registers at the start of the align frame, which is indicated by the TAF status bit in BTSR1. After TAF is set to 1, software has 250s to update the registers with new values (if needed) before they are sampled again for the next double-frame. BTAF and BTNAF are the default sources for the FAS, Si, RAI and Sa bits. However, various control fields can cause some of these bits to be sourced from elsewhere. Figure 7-16 shows the possible sources and their relative priorities. 7.10.6.4 CRC-4 Multiframe Si/RAI/Sa Insertion and Extraction On the receive side, the eight registers BRSa4 through BRSa8, BRSiAF, BRSiNAF and BRRAI report the corresponding overhead bits of the CRC-4 multiframe as they are received. These registers are updated at the start of the next CRC-4 multiframe, which is indicated by the RCMF status bit in BRSR3. After RCMF is set to 1, software has 2ms to read the registers before they are overwritten by the bits from the next multiframe. On the transmit side, the eight registers BTSa4 through BTSa8, BTSiAF, BRSiNAF and BTRAI can source the corresponding overhead bits of the multiframe. The control bits in the BTOCR register enable the sourcing of Si/RAI/Sa bits from these registers. Data is sampled from these registers at the start of the multiframe, which is indicated by the TMF status bit in BTSR1. After TMF is set to 1, software has 2ms to update the registers (if needed) before they are sampled again for the next multiframe. 7.10.6.5 SSM Extraction and Insertion G.704 specifies that synchronization status messages (SSMs) are transmitted in one of the Sa bit channels of the CRC-4 multiframe. All eight instances of the chosen Sa bit within the multiframe are used for the SSM. The four instances of the chosen Sa bit within the first sub-multiframe carry one copy of the SSM, and the four instances within the second sub-multiframe carry another copy. Each copy of the SSM is sent MSB first and is aligned with the start of the sub-multiframe. ITU recommendation G.704 lists the SSM codes carried by E1 signals.
19-4546; Rev 9; 5/09
71 of 227
DS3100 To extract SSMs from the incoming E1 data stream, the receive framer should be configured for CRC-4 multiframing (BRCR3:RCRC4 = 1). Once in this mode, system software can read incoming SSMs from the appropriate BRSaX register (X = 4, 5, 6, 7, or 8) at any time. See Section 7.10.6.4. When an incoming SSM changes, the BITS receiver validates the new value according to the criteria specified in BRMCR:SSMF. When a new SSM is validated in one of the Sa-bit channels, the corresponding status bit is set in the BRMSR register, which can cause an interrupt if enabled by the corresponding interrupt enable bit in the BRMIER register. The most recently validated SSM message in an Sa-bit channel can be read by specifying the channel in BRMCR:SSMCH and reading the SSM message from the BRSSM register. To insert SSMs into the outgoing E1 data stream, the transmit formatter should be configured for CRC-4 multiframing (BTCR4:TCRC4 = 1), and the appropriate bit(s) in the BTOCR register should be set to enable the sourcing of the selected Sa bit(s) from the corresponding BTSaX register(s). See Section 7.10.6.4.
Figure 7-16. FAS/Si/RAI/Sa Source Logic
FAS bits if BTCR4.TFPT=1 then source from TSER pin else source from BTAF register Si bits, align frame if BTOCR.SiAF=1 then source from BTSiAF register else if BTCR4:TCRC4=1 then source from CRC-4 generator else if BTCR4.TSiS=0 then source from TSER pin else if BTCR4.TFPT=1 then source from TSER pin else source from BTAF register Si bits, non-align frame if BTOCR.SiNAF=1 then source from BTSiNAF register else if BTCR4:TCRC4=1 then source from CRC-4 generator else if BTCR4.TSiS=0 then source from TSER pin else if BTCR4.TFPT=1 then source from TSER pin else source from BTNAF register SaX bit (X=4, 5, 6, 7 or 8) if BTOCR.SaX=1 then source from BTSaX register else if BTCR4.TFPT=1 then source from TSER pin else source from BTNAF register
7.10.7
G.703 2048kHz Synchronization Interface
The G.703 2048kHz synchronization interface is an unframed all-ones signal with specifications shown in Table 7-19. Figure 7-10 shows the external components required to operate the receiver and/or transmitter in this mode. 7.10.7.1 Receiver The BITS receiver is configured for 2048kHz mode when RMODE = 10 in BMCR. The receiver line impedance must be configured for 75 or 120 by setting BLCR3:RIMP[2:0] = 00 or 11. The LIU receiver declares loss of signal (BLIR1:LOS) as described in Section 7.10.4.1.6. 7.10.7.2 Transmitter The BITS transmitter is configured for 2048kHz mode when BMCR:TMODE = 10. In this mode, the transmitter line impedance must be configured for 75 or 120 by setting BLCR2:TIMP[2:0] = 00 or 11. In addition, the transmitter line build-out must be configured for 75 or 120 by setting BLCR2:LBO[2:0] = 000 or 001. After configuring the transmitter for 2048kHz mode and 75 as described above, the following write sequence must be done to optimize the LIU transmitter: write 01h to address 1FFh write F8h to address 195h (BITS1) or 1A5h for (BITS2) write 00h to address 199h (BITS1) or 1A9h (BITS2) write 00h to address 1FFh 19-4546; Rev 9; 5/09 72 of 227
DS3100 After configuring the transmitter for 2048kHz mode and 120 as described above, the following write sequence must be done to optimize the LIU transmitter: write 01h to address 1FFh write F8h to address 195h (BITS1) or 1A5h (BITS2) write 09h to address 199h (BITS1) or 1A9h (BITS2) write 00h to address 1FFh When switching the BITS transmitter from 2048kHz to some other mode, the following write sequence must be done after writing BMCR:TMODE10: write 01h to address 1FFh write 00h to address 195 h (BITS1) or 1A5h (BITS2) write 00h to address 199h (BITS1) or 1A9h (BITS2) write 00h to address 1FFh Section 7.10.3 describes how to source the 2048kHz reference from the OCx output clocks. The output signal meets the template of G.703, shown in Figure 7-15. The nominal output amplitude is 1.2V typical for 75 LBO and 1.5V typical for 120 LBO.
Table 7-19. 2048kHz Synchronization Interface Specification
PARAMETER Pulse Shape Transmission Media Test Load Impedance Maximum Peak Voltage Minimum Peak Voltage COAX SPECIFICATION TWISTED PAIR SPECIFICATION Must conform with mask of G.703 Figure 20 Coaxial pair Symmetrical pair 75 resistive 120 resistive 1.5V 1.9V 0.75V 1.0V
7.10.8
G.703 Appendix II 6312kHz Japanese Synchronization Interface
The 6312kHz synchronization interface in G.703 Appendix II is a Japanese timing signal with the specifications shown in Table 7-20. 7.10.8.1 Receiver The BITS receiver is configured for 6312kHz mode when RMODE = 11 in BMCR. The receiver line termination must be configured for 75 by setting RIMP[2:0] = 00 in BLCR3. The LIU receiver declares loss of signal (BLIR1:LOS=1) when the incoming signal level is below -24dBm. The receiver accepts both sine-wave and squarewave signals. 7.10.8.2 Transmitter The BITS transmitter does not transmit the 6312 kHz signal because it is easily generated using any of output clocks OC1 through OC7 (square wave) and an external square-to-sinusoidal conversion network.
Table 7-20. 6312kHz Synchronization Interface Specification
PARAMETER Frequency Signal Format Transmission Medium Load Impedance Amplitude Alarm Condition for Received Signal Amplitude SPECIFICATION 6312kHz Sinusoidal wave Coaxial cable 75 resistive 0 3dBm No alarm for amplitudes between -16dBm and + 3dBm
19-4546; Rev 9; 5/09
73 of 227
DS3100
7.11
Composite Clock Receivers and Transmitter
By default, input clocks IC1 and IC2 are configured as composite clock receivers. Output clock OC8 is a dedicated composite clock transmitter. These I/Os support the following composite clock variations:
Note 1: Note 2: Note 3:
GR-378 composite clock (Note 1) G.703 centralized clock (Note 2) G.703 Japanese synchronization interface (Note 3)
Complies with Telcordia GR-378 composite clock and G.703 Section 4.2.2 centralized clock option b). Complies with ITU_T G.703 Section 4.2.2 centralized clock options a) and G.703 Section 4.2.3 contradirectional interface clock. Complies with ITU_T G.703 Appendix II.1 options a) and option b) Japanese synchronization interfaces.
Composite clock (CC) signals provide both bit and byte synchronization for equipment with DS0 connections. In all CC variations, the signal is a 64kHz AMI signal with an embedded 8kHz clock indicated by a deliberate bipolar violation (BPV) every 8 clock cycles. The option b) Japanese synchronization interface in G.703 Appendix II.1 also has an embedded 400Hz clock indicated by a BPV removed every 400Hz. Details about the several composite clock variations are described in the following paragraphs and summarized in Table 7-21. GR-378 Composite Clock. As shown in Table 7-22 and Figure 7-17, the GR-378 composite clock signal has a 5/8 duty-cycle square pulse and a 133 line impedance. The G.703 Section 4.2.2 option b) centralized clock specifications are nearly identical to the GR-378 composite clock, with the exception of line termination impedance (110 for G.703 vs. 133 for GR-378). G.703 Centralized Clock and other 64kHz + 8kHz Timing Signals. G.703 Section 4.2.2 defines two centralized clock types, option a) and option b). Option b) is discussed in the GR-378 paragraph above. As shown in Table 7-23, the option a) centralized clock has a 50% duty cycle and a 110 line impedance. G.703 also specifies three other timing signals that have characteristics and specifications that are nearly identical to those of centralized clock option a). These other signals are (1) the timing signal in the 64kbps contradirectional interface defined in G.703 Section 4.2.3, (2) the 64kHz + 8kHz Japanese timing signal defined in G.703 Appendix II.1, and (3) the 64kHz + 8kHz + 400Hz Japanese timing signal defined in G.703 Appendix II.1 (which has the 8kHz BPV removed every 400Hz). Table 7-23 tabulates the requirements for each of these signals.
Table 7-21. Composite Clock Variations
VARIATION Composite Clock, GR-378 Centralized Clock, G.703 4.2.2 option b) Centralized Clock, G.703 4.2.2 option a) Japanese Sync Interface, G.703 Appendix II.1 option a) Japanese Sync Interface, G.703 Appendix II.1 option b) Contradirectional Interface Clock, G.703 4.2.3 LINE IMPEDANCE (0) 133 110 110 110 110 120 PULSE AMPLITUDE (V) 2.7 to 5.5 3.0 0.5 1.0 0.1V 1 0.1 1 0.1 1.0 0.1 NOMINAL DUTY CYCLE 5/8 5/8 50% 50% 50% 50% BPVs 8kHz 8kHz 8kHz 8kHz 8kHz, but removed at 400Hz 8kHz
19-4546; Rev 9; 5/09
74 of 227
DS3100
7.11.1
IC1 and IC2 Receivers
Input clocks IC1 and IC2 can be either composite clock receivers (via the IC1A and IC2A pins) or standard CMOS/TTL inputs (via the IC1 and IC2 pins). Configuration bits MCR5:IC1SF and IC2SF specify the signal format for IC1 and IC2, respectively. When these inputs are configured as composite clock (CC) receivers, they can directly receive incoming AMI-coded 64kHz CC signals, including those with the pre-emphasis described in GR378 Section 4.2. See the electrical specifications in Table 10-6, and the recommended external components in Figure 10-3. If IC1 and IC2 are not needed as composite clock inputs or CMOS/TTL inputs, another option is to connect the BITS receivers to these inputs (see Section 7.10.2). Each CC receiver derives an 8kHz clock from the 8kHz component of the incoming CC signal. It is this 8kHz clock that is forwarded to the input clock monitoring and selection circuitry. The falling edge of this 8kHz clock can be configured to coincide with the leading edge of the 8kHz BPV or the leading edge of the pulse following the BPV, as specified by the CCEDGE field in the MCR5 register. Incoming composite clock signals are monitored for loss-of-signal and AMI violations. When either of these signal conditions occurs, a corresponding latched status bit is set in register MSR3. When set, these status bits can cause an interrupt request on the INTREQ pin if enabled by the corresponding bits in IER3. Loss of signal is declared when no pulses are detected in the incoming signal in a 32s period (i.e., after two missing pulses, voltage threshold VLOS = 0.2V typical). The amplitude threshold for detecting a pulse is 0.2V. An AMI violation is declared when a deviation from the expected pattern of seven ones followed by a BPV occurs in each of two consecutive 8-bit periods. When MCR5:BITERR = 1, single-bit violations of the one-BPV-in-eight pattern are considered irregularities by the corresponding activity monitor and increment the leaky bucket accumulator. When MCR5:AMI = 1, the detection of an AMI violation automatically invalidates the offending clock. When MCR5:LOS = 1, the detection of loss-of-signal automatically invalidates the offending clock. In addition, register MSR4 has latched status bits that indicate the absence of the 8kHz component and the 400Hz component. In some networks the 8kHz component is removed to signal an alarm condition. If the BPVs that indicate the 8kHz component cannot be found in the incoming signal in a 500s period (four 8kHz cycles), then MSR4:ICxNO8 is set to indicate the fact. This can cause an interrupt on the INTREQ pin if enabled by the corresponding bit in IER4. This logic is always active. If the lack of the 8kHz component is not an alarm signal in the synchronization network, then IER4:ICxNO8 can be set to 0 to disable the interrupt, and MSR4:ICxNO8 can be ignored. If the 8kHz component is not present in the signal, then the CC receiver does not forward an 8kHz clock to the input monitoring logic. The input monitoring logic then declares that input clock invalid. If the missing BPVs that indicate the 400Hz component cannot be found in a 5ms period (two 400Hz cycles), then MSR4:ICxNO4 is set. This can cause an interrupt on the INTREQ pin if enabled by the corresponding bit in IER4. This logic is always active. If the 400Hz component is not expected to be present in the signal, then IER4:ICxNO4 can be set to 0 to disable the interrupt, and MSR4:ICxNO4 can be ignored. When the 8kHz component is entirely missing from the incoming signal, the AMI status bit in MSR3 is continually set, and can cause repeated interrupts if enabled. Therefore, in networks where the lack of the 8kHz component is used as an alarm signal, after MSR4:ICxNO8 is set to indicate that the 8kHz component is missing, the interrupt for MSR3:AMIx should be disabled until ICxNO8 goes low, indicating the 8kHz component is present again. Also, since the 8kHz component is the clock that is forwarded to the input clock monitor, if the 8kHz component is missing in the incoming signal, the input clock monitor automatically invalidates the clock. If the 400Hz component is missing, however, the AMI status bit is not set and the clock is not invalidated.
7.11.2
OC8 Transmitter
Output clock OC8 is a dedicated composite clock transmitter. See the recommended external components in Figure 10-3. OC8 is a differential output consisting of pins OC8POS and OC8NEG. These pins are enabled/disabled by OCR4:OC8EN. Either 50% or 5/8 duty cycle can be selected by setting T4CR1:OC8DUTY appropriately. In some networks the 8kHz component (i.e., the one BPV every eight cycles) is removed to signal an alarm condition; the 8kHz component of the OC8 signal can be removed as needed by setting MCR8:OC8NO8 = 1. When the selected reference is either IC1 or IC2 and that input is configured in AMI/CC mode (MCR5:IcxSF = 0), and the signal on that input has an 8kHz component (MSR4:ICxNO8 = 0), then the output BPVs on OC8 (the 8kHz component) are closely aligned (within a few s) to the input BPVs but may be of opposite polarity. 19-4546; Rev 9; 5/09 75 of 227
DS3100 To support the G.703 Appendix II.1 option b) Japanese synchronization interface, the 400Hz component (i.e., the removed BPV every 160 cycles) can be enabled by setting MCR8:OC8400 = 1. If the selected reference is either IC1 or IC2 and that input is configured in AMI/CC mode (MCR5:IcxSF = 0) and the signal on that input has a 400 Hz component (MSR4:ICxNO4 = 0), then OC8's 400Hz component is aligned with the input 400 Hz component but may be the opposite polarity. Otherwise, the 400Hz component for OC8 is divided down from OC8's 8kHz component. Setting OC8400 = 1 has no effect if OC8NO8 = 1. See Section 7.8.2.4 for additional OC8 configuration details.
Table 7-22. GR-378 Composite Clock Interface Specification
PARAMETER Nominal Line Rate Line-Rate Accuracy Line Code Medium Test Load Impedance Pulse Amplitude Pulse Shape Pulse Imbalance DC Power SPECIFICATION 64kHz with 8kHz bipolar violation. Accuracy of the network clock. Bipolar (AMI), return-to-zero, with 5/8 duty cycle. A shielded, balanced twisted pair. The resistive test load of 133 (5%) shall be used at the interface for evaluation of the pulse shape and the electrical parameters. The amplitude of an isolated pulse shall be between 2.7V and 5.5V. The shape of an isolated pulse shall be rectangular with rise and fall times less than 0.5s such that the pulse fits the shape of the mask in Figure 7-17. The ratio of the amplitudes of the positive and negative pulses shall be from 0.95 to 1.05. The ratio of the widths of the positive and negative pulses shall be from 0.95 to 1.05. No DC power shall be applied to the interface.
Figure 7-17. GR-378 Composite Clock Pulse Mask
1.2 1.0 0.8 0.6 0.4 0.2 0 -0.2 0 0.2 0.4 0.6 Time (UI) 0.8 1.0
Minimum Normalized Amplitude -0.05 0.95 -0.05 -0.05 -0.05 Minimum Normalized Amplitude 1.05 1.05 1.05 0.05 0.05
Normalized Amplitude
Time (UI) 0 0.032 0.625 0.657 1
Table 7-23. G.703 Synchronization Interfaces Specification
PARAMETER Pulse Shape Transmission Media Nominal Test Load Impedance Peak Voltage of a Mark (Pulse) Peak Voltage of a Space (No Pulse) Nominal Pulse Width Pulse Imbalance Alarm Condition for Received Signal Amplitude 19-4546; Rev 9; 5/09 SPECIFICATION Nominally rectangular, with rise and fall times less than 1s. Symmetric pair cable. 110 resistive (centralized clock and appendix II Japanese signals). 120 resistive (contradirectional interface). 1.0V 0.1V 0V 0.1V 7.8s 0.78s The ratio of the amplitudes of the positive and negative pulses shall be from 0.95 to 1.05. The ratio of the widths of the positive and negative pulses shall be from 0.95 to 1.05. No alarm for pulse amplitudes between 0.63V0-P. and 1.1V0-P.
76 of 227
DS3100
7.12
Microprocessor Interfaces
The DS3100 microprocessor interface can be configured for 8-bit parallel or SPI serial operation. During reset, the device determines its interface mode by latching the state of the IFSEL[2:0] pins into the IFSEL field of the IFCR register. Table 7-24 shows possible values of IFSEL.
Table 7-24. Microprocessor Interface Modes
IFSEL[2:0] 010 011 100 101 110 111 000, 001 MODE Intel bus mode (multiplexed) Intel bus mode (nonmultiplexed) Motorola mode (nonmultiplexed) SPI mode (LSB first) Motorola mode (multiplexed) SPI mode (MSB first) {unused value}
7.12.1
Parallel Interface Modes
In the Motorola interface modes, the interface is Motorola-style with CS, R/W, and DS control lines. In the Intel modes, the interface is Intel-style with CS, RD, and WR control lines. For multiplexed bus modes, the A[8], AD[7:0], and ALE pins are wired to the corresponding pins on the microprocessor, and the falling edge of ALE latches the address on A[8] and AD[7:0]. For nonmultiplexed bus modes, the A[8:0] and AD[7:0] pins are wired to the corresponding pins on the micro, and the falling edge of ALE latches the address on A[8:0]. In nonmultiplexed bus modes, ALE is typically wired high to make the latch transparent. See Section 10.5 for AC timing details.
7.12.2
SPI Interface Mode
In the SPI modes, the device presents an SPI interface on the CS, SCLK, SDI, and SDO pins. SPI is a widely used master/slave bus protocol that allows a master device and one or more slave devices to communicate over a serial bus. The DS3100 is always a slave device. Masters are typically microprocessors, ASICs, or FPGAs. Data transfers are always initiated by the master device, which also generates the SCLK signal. The DS3100 receives serial data on the SDI pin and transmits serial data on the SDO pin. SDO is high impedance except when the DS3100 is transmitting data to the bus master. Bit Order. When IFCR:IFSEL = 101, the register address and all data bytes are transmitted LSB first on both SDI and SDO. When IFSEL = 111, the register address and all data bytes are transmitted MSB first on both SDI and SDO. The Motorola SPI convention is MSB first. Clock Polarity and Phase. The CPOL pin defines the polarity of SCLK. When CPOL = 0, SCLK is normally low and pulses high during bus transactions. When CPOL = 1, SCLK is normally high and pulses low during bus transactions. The CPHA pin sets the phase (active edge) of SCLK. When CPHA = 0, data is latched in on SDI on the leading edge of the SCLK pulse and updated on SDO on the trailing edge. When CPHA = 1, data is latched in on SDI on the trailing edge of the SCLK pulse and updated on SDO on the following leading edge. SCLK does not have to toggle between access, i.e., when CS is high. See Figure 7-18. Device Selection. Each SPI device has its own chip-select line. To select the DS3100, pull its CS pin low. Control Word. After CS is pulled low, the bus master transmits the control word during the first 16 SCLK cycles. In MSB-first mode, the control word has the form: R/W A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 BURST
where A[13:0] is the register address, R/W is the data direction bit (1 = read, 0 = write), and BURST is the burst bit (1 = burst access, 0 = single-byte access). In LSB-first mode, the order of the 14 address bits is reversed. In the discussion that follows, a control word with R/W = 1 is a read control word, while a control word with R/W = 0 is a write control word. Single-Byte Writes. See Figure 7-19. After CS goes low, the bus master transmits a write control word with BURST = 0 followed by the data byte to be written. The bus master then terminates the transaction by pulling CS high. 19-4546; Rev 9; 5/09 77 of 227
DS3100 Single-Byte Reads. See Figure 7-19. After CS goes low, the bus master transmits a read control word with BURST = 0. The DS3100 then responds with the requested data byte. The bus master then terminates the transaction by pulling CS high. Burst Writes. See Figure 7-19. After CS goes low, the bus master transmits a write control word with BURST = 1 followed by the first data byte to be written. The DS3100 receives the first data byte on SDI, writes it to the specified register, increments its internal address register, and prepares to receive the next data byte. If the master continues to transmit, the DS3100 continues to write the data received and increment its address counter. After the address counter reaches 3FFFh, it rolls over to address 0000h and continues to increment. Burst Reads. See Figure 7-19. After CS goes low, the bus master transmits a read control word with BURST = 1. The DS3100 then responds with the requested data byte on SDO, increments its address counter, and prefetches the next data byte. If the bus master continues to demand data, the DS3100 continues to provide the data on SDO, increment its address counter, and prefetch the following byte. After the address counter reaches 3FFFh, it rolls over to address 0000h and continues to increment. Early Termination of Bus Transactions. The bus master can terminate SPI bus transactions at any time by pulling CS high. In response to early terminations, the DS3100 resets its SPI interface logic and waits for the start of the next transaction. If a write transaction is terminated prior to the SCLK edge that latches the LSB of a data byte, the data byte is not written. Design Option: Wiring SDI and SDO Together. Because communication between the bus master and the DS3100 is half-duplex, the SDI and SDO pins can be wired together externally to reduce wire count. To support this option, the bus master must not drive the SDI/SDO line when the DS3100 is transmitting. AC Timing. See Table 10-14 and Figure 10-8 for AC timing specifications for the SPI interface.
Figure 7-18. SPI Clock Polarity and Phase Options
CS
SCK CPOL = 0, CPHA = 0 SCK CPOL = 0, CPHA = 1 SCK CPOL = 1, CPHA = 0 SCK CPOL = 1, CPHA = 1 SDI/SDO MSB 6 5 4 3 2 1 LSB
CLOCK EDGE USED FOR DATA CAPTURE (ALL MODES)
19-4546; Rev 9; 5/09
78 of 227
DS3100
Figure 7-19. SPI Bus Transactions
Single-Byte Write
CS SDI SDO R/W Register Address Burst
0 (Write)
Data Byte
0 (single-byte)
Single-Byte Read
CS SDI SDO R/W Register Address Burst
1 (Read) 0 (single-byte)
Data Byte
Burst Write
CS SDI SDO R/W Register Address Burst Data Byte 1
0 (Write) 1 (burst)
Data Byte N
Burst Read
CS SDI R/W Register Address Burst
1 (Read) 1 (burst)
Data Byte 1
Data Byte N
7.13
Reset Logic
The device has three reset controls: the RST pin, the RST bit in MCR1, and the JTAG reset pin, JTRST. The RST pin asynchronously resets the entire device, except for the JTAG logic. When the RST pin is low, all internal registers are reset to their default values, including those fields that latch their default values from, or based on, the states of input pins when the RST pin goes high (such as IFCR:IFSEL[2:0]). The RST pin must be asserted once after power-up while the external oscillator is stabilizing. The MCR1:RST bit resets the entire device (except for the microprocessor interface, the JTAG logic, and the RST bit itself), but when RST is active, the register fields with pin-programmed defaults do not latch their values from, or based on, the corresponding input pins. Instead, these fields are reset to the default values that were latched when the RST pin was last active. Systems should hold RST low while the external oscillator starts up and stabilizes. Some OCXOs take 250ms or more to start up and stabilize their output signals to valid logic levels and pulse widths. An incorrect reset condition could result if RST is released before the oscillator has started up completely. Important: System software must wait at least 100s after reset (RST pin or RST bit) is deasserted before initializing the device as described in Section 7.15.
19-4546; Rev 9; 5/09
79 of 227
DS3100
7.14
Power-Supply Considerations
Due to the dual-power-supply nature of the DS3100, some I/Os have parasitic diodes between a 1.8V supply and a 3.3V supply. When ramping power supplies up or down, care must be taken to avoid forward-biasing these diodes because it could cause latchup. Two methods are available to prevent this. The first method is to place a Schottky diode external to the device between the 1.8V supply and the 3.3V supply to force the 3.3V supply to be less than one parasitic diode drop below the 1.8V supply. The second method is to ramp up the 3.3V supply first and then ramp up the 1.8V supply.
7.15
Initialization
After power-up or reset, a series of writes must be done to the DS3100 to tune it for optimal performance. This series of writes is called the initialization script. Each die revision of the DS3100 has a different initialization script. Download the latest initialization scripts from the DS3100 website at www.maxim-ic.com/DS3100.
19-4546; Rev 9; 5/09
80 of 227
DS3100
8.
REGISTER DESCRIPTIONS
The top-level memory map is shown in Table 8-1. In addition to the registers for the core timing block, the memory map also includes space for the two identical BITS transceivers, BITS1 and BITS2.
Table 8-1. Top-Level Memory Map
ADDRESS RANGE 0000-007Fh 0080-00FFh 0100-017Fh 0180-01FFh FUNCTIONAL BLOCK Core PLL Block BITS Transceiver 1 (BITS1) BITS Transceiver 2 (BITS2) Reserved Note: Systems must be able to access the entire address range from 0 to 01FFh. Proper device initialization requires a sequence of writes to addresses in the range 0180-01FFh.
Table 8-2 in Section 8.4 shows the register map for the core timing block, while Table 8-3 in Section 8.5 shows the register map for the BITS transceivers. In each register, bit 7 is the MSB and bit 0 is the LSB. Register addresses not listed and bits marked "--" are reserved and must be written with 0. Writing other values to these registers may put the device in a factory test mode, resulting in undefined operation. Bits labeled "0" or "1" must be written with that value for proper operation. Register fields with underlined names are read-only fields; writes to these fields have no effect. All other fields are read-write. Register fields are described in detail in the register descriptions that follow Table 8-2.
8.1
Status Bits
The device has two types of status bits. Real-time status bits are read-only and indicate the state of a signal at the time it is read. Latched status bits are set when a signal changes state (low-to-high, high-to-low, or both, depending on the bit) and cleared when written with a logic 1 value. Writing a 0 has no effect. When set, some latched status bits can cause an interrupt request on the INTREQ pin if enabled to do so by corresponding interrupt enable bits.
8.2
Configuration Fields
Configuration fields are read-write. During reset, each configuration field reverts to the default value shown in the register definition. Configuration register bits marked "--" are reserved and must be written with 0.
8.3
Multiregister Fields
Multiregister fields--such as FREQ[18:0] in registers FREQ1, FREQ2, and FREQ3--must be handled carefully to ensure that the bytes of the field remain consistent. A write access to a multiregister field is accomplished by writing all the registers of the field in any order, with no other accesses to the device in between. If the write sequence is interrupted by another access, none of the bytes are written and the MSR4:MRAA bit is set to indicate the write was aborted. A read access from a multiregister field is accomplished by reading the registers of the field in any order, with no other accesses to the device in between. When one register of a multiregister field is read, the other register(s) in the field are frozen until after they are all read. If the read sequence is interrupted by another access, the registers of the multibyte field are unfrozen and the MSR4:MRAA bit is set to indicate the read was aborted. For best results, interrupt servicing should be disabled in the microprocessor before a multiregister access and then enabled again after the access is complete. The multiregister fields are: FIELD REGISTERS FREQ[18:0] FREQ1, FREQ2, FREQ3 MCLKFREQ[15:0] MCLK1, MCLK2 HOFREQ[18:0] HOCR1, HOCR2, HOCR3* HARDLIM[9:0] DLIMIT1, DLIMIT2 DIVN[14:0] DIVN1, DIVN2 OFFSET[15:0] OFFSET1, OFFSET2 PHASE[15:0] PHASE1, PHASE2 *HOCR3 is a special case because its upper 5 bits are not part of a ADDRESSES 07, 0C, 0D 3C, 3D 3E, 3F, 40 41, 42 46, 47 70, 71 77, 78 TYPE read-only read/write read/write read/write read/write read/write read-only
multiregister field, but its lower 3 bits are part of the HOFREQ[18:0] multiregister field. Writes to HOCR3 immediately update the upper 5 bits without any requirement to also write HOCR1 and HOCR2. The lower 3 bits of HOCR3 (HOFREQ[18:16]), however, can only be written as part of a proper write sequence for a multiregister field, as described above. A write to HOCR3 continugous with writes to HOCR1 and HOCR2 can simultaneously write the upper 5 bits immediately and start/continue/complete a multiregister write of HOFREQ[18:0].
19-4546; Rev 9; 5/09
81 of 227
DS3100
8.4
Core Register Definitions
Table 8-2. Core Register Map
Note: Register names are hyperlinks to register definitions. Underlined fields are read-only.
ADDR
REGISTER
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
00h 01 02 03 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 30 31 32 33 34
ID1 ID2 REV TEST1 MSR1 MSR2 FREQ3 MSR3 OPSTATE PTAB1 PTAB2 FREQ1 FREQ2 VALSR1 VALSR2 ISR1 ISR2 ISR3 ISR4 ISR5 ISR6 ISR7 MSR4 IPR1 IPR2 IPR3 IPR4 IPR5 IPR6 IPR7 ICR1 ICR2 ICR3 ICR4 ICR5 ICR6 ICR7 ICR8 ICR9 ICR10 ICR11 ICR12 ICR13 ICR14 VALCR1 VALCR2 MCR1 MCR2 MCR3
PALARM IC8 STATE -- FSMON FSMON
D180 -- IC7 IC6 SRFAIL IC14 -- -- T4LOCK PHMON T4LOCK T0SOFT REF1[3:0] REF3[3:0]
ID[7:0] ID[15:8] REV[7:0] RA 0 IC5 IC4 IC13 IC12 -- -- T4NOIN AMI2 T4SOFT -- FREQ[7:0] FREQ[15:8] IC5 IC4 IC13 IC12 LOCK2 SOFT1 LOCK4 SOFT3 LOCK6 SOFT5 LOCK8 SOFT7 LOCK10 SOFT9 LOCK12 SOFT11 LOCK14 SOFT13 -- IC2NO4
8KPOL IC3 IC11
0 0 IC2 IC1 IC10 IC9 FREQ[18:16] LOS2 AMI1 LOS1 T0STATE[2:0] SELREF[3:0] REF2[3:0]
IC8 IC7 IC6 FHORDY SHORDY IC14 SOFT2 HARD2 ACT2 SOFT4 HARD4 ACT4 SOFT6 HARD6 ACT6 SOFT8 HARD8 ACT8 SOFT10 HARD10 ACT10 SOFT12 HARD12 ACT12 SOFT14 HARD14 ACT14 FHORDY SHORDY MRAA PRI2[3:0] PRI4[3:0] PRI6[3:0] PRI8[3:0] PRI10[3:0] PRI12[3:0] PRI14[3:0] DIVN LOCK8K BUCKET[1:0] DIVN LOCK8K BUCKET[1:0] DIVN LOCK8K BUCKET[1:0] DIVN LOCK8K BUCKET[1:0] DIVN LOCK8K BUCKET[1:0] DIVN LOCK8K BUCKET[1:0] DIVN LOCK8K BUCKET[1:0] DIVN LOCK8K BUCKET[1:0] DIVN LOCK8K BUCKET[1:0] DIVN LOCK8K BUCKET[1:0] DIVN LOCK8K BUCKET[1:0] DIVN LOCK8K BUCKET[1:0] DIVN LOCK8K BUCKET[1:0] DIVN LOCK8K BUCKET[1:0] IC8 IC7 IC6 IC5 -- -- IC14 IC13 RST -- -- -- -- -- -- -- AEFSEN LKATO XOEDGE MANHO
IC4 IC12 -- EFSEN
IC3 IC2 IC1 IC11 IC10 IC9 HARD1 ACT1 LOCK1 HARD3 ACT3 LOCK3 HARD5 ACT5 LOCK5 HARD7 ACT7 LOCK7 HARD9 ACT9 LOCK9 HARD11 ACT11 LOCK11 HARD13 ACT13 LOCK13 IC1NO4 IC2NO8 IC1NO8 PRI1[3:0] PRI3[3:0] PRI5[3:0] PRI7[3:0] PRI9[3:0] PRI11[3:0] PRI13[3:0] FREQ[3:0] FREQ[3:0] FREQ[3:0] FREQ[3:0] FREQ[3:0] FREQ[3:0] FREQ[3:0] FREQ[3:0] FREQ[3:0] FREQ[3:0] FREQ[3:0] FREQ[3:0] FREQ[3:0] FREQ[3:0] IC3 IC2 IC1 IC11 IC10 IC9 T0STATE[2:0] T0FORCE[3:0] SONSDH MASTSLV REVERT 82 of 227
19-4546; Rev 9; 5/09
DS3100
ADDR REGISTER BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
35 36 37 38 39 3A 3B 3C 3D 3E 3F 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 69 6A 6B 6C 6D
MCR4 MCR5 IFSR MCR6 MCR7 MCR8 MCR9 MCLK1 MCLK2 HOCR1 HOCR2 HOCR3 DLIMIT1 DLIMIT2 IER1 IER2 IER3 DIVN1 DIVN2 MCR10 ILIMIT SRLIMIT MCR11 FMEAS DLIMIT3 IER4 LB0U LB0L LB0S LB0D LB1U LB1L LB1S LB1D LB2U LB2L LB2S LB2D LB3U LB3L LB3S LB3D OCR1 OCR2 OCR3 OCR4 T4CR1 T0CR1 T4BW T0LBW T0ABW T4CR2 T0CR2 T4CR3 T0CR3
-- OC89 T4FORCE[3:0] AMI LOS IC2SF IC1SF IC6SF IC5SF -- -- -- IFSEL[2:0] DIG1SS -- -- -- -- -- DIG1F[1:0] -- -- -- -- OC8400 OC8NO8 OC7SF OC6SF -- -- LIMINT PFD180 -- -- MCLKFREQ[7:0] MCLKFREQ[15:8] HOFREQ[7:0] HOFREQ[15:8] AVG FAST RDAVG MINIHO[1:0] HOFREQ[18:16] HARDLIM[7:0] -- -- -- -- -- -- HARDLIM[9:8] IC8 IC7 IC6 IC5 IC4 IC3 IC2 IC1 STATE SRFAIL IC14 IC13 IC12 IC11 IC10 IC9 FSMON T4LOCK PHMON T4NOIN AMI2 LOS2 AMI1 LOS1 DIVN[7:0] -- DIVN[14:8] FMONCLK SRFPIN UFSW EXTSW PBOFRZ PBOEN SOFTEN HARDEN SOFT[3:0] HARD[3:0] SOFT[3:0] HARD[3:0] -- -- -- T4T0 FMEASIN[3:0] FMEAS[7:0] FLLOL SOFTLIM[6:0] FHORDY SHORDY -- -- IC2NO4 IC1NO4 IC2NO8 IC1NO8 LB0U[7:0] LB0L[7:0] LB0S[7:0] -- -- -- -- -- -- LB0D[1:0] LB1U[7:0] LB1L[7:0] LB1S[7:0] -- -- -- -- -- -- LB1D[1:0] LB2U[7:0] LB2L[7:0] LB2S[7:0] -- -- -- -- -- -- LB2D[1:0] LB3U[7:0] LB3L[7:0] LB3S[7:0] -- -- -- -- -- -- LB3D[1:0] OFREQ2[3:0] OFREQ1[3:0] OFREQ4[3:0] OFREQ3[3:0] OFREQ6[3:0] OFREQ5[3:0] OC11EN OC10EN OC9EN OC8EN OFREQ7[3:0] -- ASQUEL OC8DUTY OC9SON T4FREQ[3:0] T4MT0 T4APT0 T0FT4[2:0] T0FREQ[2:0] -- -- -- -- -- -- T4BW[1:0] -- -- -- T0LBW[4:0] -- -- -- T0ABW[4:0] -- PD2GA8K[2:0] -- DAMP[2:0] -- PD2GA8K[2:0] -- DAMP[2:0] PD2EN PD2GA[2:0] -- PD2GD[2:0] PD2EN PD2GA[2:0] -- PD2GD[2:0] 83 of 227
LKT4T0 T4DFB CCEDGE BITERR -- -- DIG2AF DIG2SS DIG2F[1:0] -- -- AUTOBW --
19-4546; Rev 9; 5/09
DS3100
ADDR REGISTER BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
6E 6F 70 71 72 73 74 76 77 78 79 7A 7B 7C 7D 7E 7F
GPCR GPSR OFFSET1 OFFSET2 PBOFF PHLIM1 PHLIM2 PHMON PHASE1 PHASE2 PHLKTO FSCR1 FSCR2 FSCR3 INTCR PROT IFCR
GPIO1D GPIO4O GPIO3O GPIO2O GPIO1O -- GPIO4 GPIO3 GPIO2 GPIO1 OFFSET[7:0] OFFSET[15:8] -- -- PBOFF[5:0] FLEN NALOL 1 -- -- FINELIM[2:0] CLEN MCPDEN USEMCPD -- COARSELIM[3:0] NW -- PMEN PMPBEN PMLIM[3:0] PHASE[7:0] PHASE[15:8] PHLKTOM[1:0] PHLKTO[5:0] 2K8KSRC -- -- -- 8KINV 8KPUL 2KINV 2KPUL INDEP OCN -- -- -- -- PHASE[1:0] RECAL MONLIM[2:0] SOURCE[3:0] -- -- -- -- -- GPO OD POL PROT[7:0] -- -- -- -- -- IFSEL[2:0]
GPIO4D --
GPIO3D --
GPIO2D --
Core Register Map Color Coding Device Identification and Protection Local Oscillator and Master Clock Configuration Input Clock Configuration Input Clock Monitoring Input Clock Selection DPLL Configuration DPLL State Output Clock Configuration SYNC2K Configuration Microprocessor Interface Configuration Unused Core Register Addresses 04h, 1Fh, 2Eh, 2Fh, 4Fh, 68h, 75h
19-4546; Rev 9; 5/09
84 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 0 ID1 Device Identification Register, LSB 00h Bit 6 0 Bit 5 0 Bit 4 ID[7:0] 1 1 1 0 0 Bit 3 Bit 2 Bit 1 Bit 0
Bits 7 to 0: Device ID (ID[7:0]). ID[15:0] = 0C1Ch = 3100 decimal.
Register Name: Register Description: Register Address: Bit 7 Name Default 0
ID2 Device Identification Register, MSB 01h Bit 6 0 Bit 5 0 Bit 4 0 Bit 3 ID[15:8] 1 Bit 2 1 Bit 1 0 Bit 0 0
Bits 7 to 0: Device ID (ID[15:8]). See the ID1 register description.
Register Name: Register Description: Register Address: Bit 7 Name Default 0
REV Device Revision Register 02h Bit 6 0 Bit 5 0 Bit 4 Bit 3 REV[7:0] 0 0 Bit 2 0 Bit 1 0 Bit 0 0
Bits 7 to 0: Device Revision (REV[7:0]). Contact the factory to interpret this value and determine the latest revision.
19-4546; Rev 9; 5/09
85 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 PALARM 0 TEST1 Test Register 1 (Not Normally Used) 03h Bit 6 D180 0 Bit 5 -- 0 Bit 4 RA 1 Bit 3 0 0 Bit 2 8KPOL 1 Bit 1 0 0 Bit 0 0 0
Name Default
Bit 7: Phase Alarm (PALARM). This real-time status bit indicates the state of T0 DPLL phase lock. 0 = T0 phase-locked to input reference 1 = T0 loss of phase lock Bit 6: Disable 180 (D180). When locking to a new reference, the T0 DPLL first tries nearest-edge locking (180) for the first two seconds. If unsuccessful it then tries full phase/frequency locking (360). Disabling the nearestedge locking can reduce lock time by up to two seconds but may cause an unnecessary phase shift (up to 360) when the new reference is close in frequency/phase to the old reference. See Section 7.7.5. 0 = normal operation: try nearest-edge locking then phase/frequency locking 1 = phase/frequency locking only Bit 4: Resync Analog Dividers (RA). When this bit is set the T0 APLL output dividers are always synchronized to ensure that low-frequency outputs are in sync with the higher-frequency clock from the T0 DPLL. 0 = not synchronized 1 = always synchronized Bit 3: Leave set to zero (test control). Bit 2: 8kHz Edge Polarity (8KPOL). Specifies the input clock edge to lock to on the selected reference when it is configured for LOCK8K mode. See Section 7.4.2. 0 = Falling edge 1 = Rising edge Bit 1: Leave set to zero (test control). Bit 0: Leave set to zero (test control).
19-4546; Rev 9; 5/09
86 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 IC8 1 MSR1 Master Status Register 1 05h Bit 6 IC7 1 Bit 5 IC6 1 Bit 4 IC5 1 Bit 3 IC4 1 Bit 2 IC3 1 Bit 1 IC2 1 Bit 0 IC1 1
Name Default
Bits 7 to 0: Input Clock Status Change (IC8 to IC1). Each of these latched status bits is set to 1 when the corresponding VALSR1 status bit changes state (set or cleared). If soft frequency limit alarms are enabled (MCR10:SOFTEN = 1), then each of these latched status bits is also set to 1 when the corresponding SOFT bit in the ISR registers changes state (set or cleared). Each bit is cleared when written with a 1 and not set again until either the VALSR1 bit or the SOFT bit changes state again. When one of these latched status bits is set it can cause an interrupt request on the INTREQ pin if the corresponding interrupt enable bit is set in the IER1 register. See Section 7.5 for input clock validation/invalidation criteria.
Register Name: Register Description: Register Address: Bit 7 STATE 0
MSR2 Master Status Register 2 06h Bit 6 SRFAIL 0 Bit 5 IC14 1 Bit 4 IC13 1 Bit 3 IC12 1 Bit 2 IC11 1 Bit 1 IC10 1 Bit 0 IC9 1
Name Default
Bit 7: T0 DPLL State Change (STATE). This latched status bit is set to 1 when the operating state of the T0 DPLL changes. STATE is cleared when written with a 1 and not set again until the operating state changes again. When STATE is set it can cause an interrupt request on the INTREQ pin if the STATE interrupt enable bit is set in the IER2 register. The current operating state can be read from the T0STATE field of the OPSTATE register. See Section 7.7.1. Bit 6: Selected Reference Failed (SRFAIL). This latched status bit is set to 1 when the selected reference to the T0 DPLL fails (i.e., no clock edges in two UI). SRFAIL is cleared when written with a 1. When SRFAIL is set it can cause an interrupt request on the INTREQ pin if the SRFAIL interrupt enable bit is set in the IER2 register. SRFAIL is not set in free-run mode or holdover mode. See Section 7.5.3. Bits 5 to 0: Input Clock Status Change (IC14 to IC9). Each of these latched status bits is set to 1 when the corresponding VALSR status bit changes state (set or cleared). If soft frequency limit alarms are enabled (MCR10:SOFTEN = 1), then each of these latched status bits is also set to 1 when the corresponding SOFT bit in the ISR registers changes state (set or cleared). Each bit is cleared when written with a 1 and not set again until either the VALSR2 bit or the SOFT bit changes state again. When one of these latched status bits is set it can cause an interrupt request on the INTREQ pin if the corresponding interrupt enable bit is set in the IER2 register. See Section 7.5 for input clock validation/invalidation criteria.
Register Name: Register Description: Register Address: Bit 7 -- 0
FREQ3 Frequency Register 3 07h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 0 Bit 1 FREQ[18:16] 0 Bit 0 0
Name Default
Bits 2 to 0: Current DPLL Frequency (FREQ[18:16]). See the FREQ1 register description.
19-4546; Rev 9; 5/09
87 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 FSMON 0 MSR3 Master Status Register 3 08h Bit 6 T4LOCK 1 Bit 5 PHMON 0 Bit 4 T4NOIN 1 Bit 3 AMI2 0 Bit 2 LOS2 0 Bit 1 AMI1 0 Bit 0 LOS1 0
Name Default
Bit 7: Frame Sync Input Monitor Alarm (FSMON). This latched status bit is set to 1 when OPSTATE:FSMON transitions from 0 to 1. FSMON is cleared when written with a 1. When FSMON is set it can cause an interrupt request on the INTREQ pin if the FSMON interrupt enable bit is set in the IER3 register. See Section 7.9.3. Bit 6: T4 DPLL Lock Status Change (T4LOCK). This latched status bit is set to 1 when the lock status of the T4 DPLL (OPSTATE:T4LOCK) changes (becomes locked when previously unlocked or becomes unlocked when previously locked). T4LOCK is cleared when written with a 1 and not set again until the T4 lock status changes again. When T4LOCK is set it can cause an interrupt request on the INTREQ pin if the T4LOCK interrupt enable bit is set in the IER3 register. See Section 7.7.6. Bit 5: Phase Monitor Alarm (PHMON). This latched status bit is set to 1 when the phase monitor alarm limit has been exceeded (PMLIM field of the PHMON register). PHMON is cleared when written with a 1 and not set again until the threshold is exceeded again. When PHMON is set it can cause an interrupt request on the INTREQ pin if the PHMON interrupt enable bit is set in the IER3 register. See Section 7.7.7. Bit 4: T4 No Valid Inputs Alarm (T4NOIN). This latched status bit is set to 1 when the T4 DPLL has no valid inputs available. T4NOIN is cleared when written with a 1 unless the T4 DPLL still has no valid inputs available. When T4NOIN is set it can cause an interrupt request on the INTREQ pin if the T4NOIN interrupt enable bit is set in the IER3 register. See Section 7.5. Bit 3: AMI Violation on IC2 (AMI2). This latched status bit is set to 1 when a deviation from the expected pattern of seven ones followed by a BPV occurs on the IC2 input in each of two consecutive 8-bit periods. However, if the composite clock receiver can detect the presence of the 400 Hz component required by G.703 Appendix II.1 option b), then the missing BPVs that indicate the 400 Hz component are not considered AMI violations. AMI2 is cleared when written with a 1 and not set again until another AMI violation occurs. When AMI2 is set it can cause an interrupt request on the INTREQ pin if the AMI2 interrupt enable bit is set in the IER3 register. This status bit is only enabled when IC2 is configured as a composite clock receiver (MCR5:IC2SF = 0). See Section 7.11.1. Bit 2: LOS Error on IC2 (LOS2). This latched status bit is set to 1 when no pulses are detected on the IC2 input in a 32s period (i.e., after two missing pulses). LOS2 is cleared when written with a 1 and is not set again until IC2 transitions from valid signal to loss-of-signal again. When LOS2 is set it can cause an interrupt request on the INTREQ pin if the LOS2 interrupt enable bit is set in the IER3 register. This status bit is only enabled when IC2 is configured as a composite clock receiver (MCR5:IC2SF = 0). See Section 7.11.1. Bit 1: AMI Violation on IC1 (AMI1). This latched status bit is set to 1 when a deviation from the expected pattern of seven ones followed by a BPV occurs on the IC1 input in each of two consecutive 8-bit periods. However, if the composite clock receiver can detect the presence of the 400Hz component required by G.703 Appendix II.1 option b), then the missing BPVs that indicate the 400Hz component are not considered AMI violations. AMI1 is cleared when written with a 1 and not set again until another AMI violation occurs. When AMI1 is set it can cause an interrupt request on the INTREQ pin if the AMI1 interrupt enable bit is set in the IER3 register. This status bit is only enabled when IC1 is configured as a composite clock receiver (MCR5:IC1SF = 0). See Section 7.11.1. Bit 0: LOS Error on IC1 (LOS1). This latched status bit is set to 1 when no pulses are detected on the IC1 input in a 32 s period (i.e., after two missing pulses). LOS1 is cleared when written with a 1 and is not set again until IC1 transitions from valid signal to loss-of-signal again. When LOS1 is set it can cause an interrupt request on the INTREQ pin if the LOS1 interrupt enable bit is set in the IER3 register. This status bit is only enabled when IC1 is configured as a composite clock receiver (MCR5:IC1SF = 0). See Section 7.11.1.
19-4546; Rev 9; 5/09
88 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 FSMON 0 OPSTATE Operating State Register 09h Bit 6 T4LOCK 1 Bit 5 T0SOFT 0 Bit 4 T4SOFT 0 Bit 3 -- 0 Bit 2 0 Bit 1 T0STATE[2:0] 0 Bit 0 1
Name Default
Bit 7: Frame Sync Input Monitor Alarm (FSMON). This real-time status bit indicates the current status of the frame sync input monitor. See Section 7.9.3. 0 = no alarm 1 = alarm Bit 6: T4 DPLL Lock Status (T4LOCK). This real-time status bit indicates the current phase lock status of the T4 DPLL. See Sections 7.5.3 and 7.7.6. 0 = not locked to selected reference 1 = locked to selected reference Bit 5: T0 DPLL Frequency Soft Alarm (T0SOFT). This real-time status bit indicates whether or not the T0 DPLL is tracking its reference within the soft alarm limits specified in the SOFT[6:0] field of the DLIMIT3 register. See Section 7.7.6. 0 = No alarm; frequency is within the soft alarm limits 1 = Soft alarm; frequency is outside the soft alarm limits Bit 4: T4 DPLL Frequency Soft Alarm (T4SOFT). This real-time status bit indicates whether or not the T4 DPLL is tracking its reference within the soft alarm limits specified in the SOFT[6:0] field of the DLIMIT3 register. See Section 7.7.6. 0 = No alarm; frequency is within the soft alarm limits 1 = Soft alarm; frequency is outside the soft alarm limits Bits 2 to 0: T0 DPLL Operating State (T0STATE[2:0]). This real-time status field indicates the current state of the T0 DPLL state machine. Values not listed below correspond to invalid (unused) states. See Section 7.7.1. 001 = Free-run 010 = Holdover 100 = Locked 101 = Prelocked 2 110 = Prelocked 111 = Loss-of-lock
19-4546; Rev 9; 5/09
89 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 0 PTAB1 Priority Table Register 1 0Ah Bit 6 Bit 5 REF1[3:0] 0 0 Bit 4 0 Bit 3 0 Bit 2 Bit 1 SELREF[3:0] 0 0 Bit 0 0
Bits 7 to 4: Highest Priority Valid Reference (REF1[3:0]). This real-time status field indicates the highest-priority valid input reference. When T4T0 = 0 in the MCR11 register, this field indicates the highest priority reference for the T0 DPLL. When T4T0 = 1, it indicates the highest priority reference for the T4 DPLL. Note that an input reference cannot be indicated in this field if it has been marked invalid in the VALCR1 or VALCR2 register. When the T0 DPLL is in non-revertive mode (REVERT = 0 in the MCR3 register) this field may not have the same value as the SELREF[3:0] field. See Section 7.6.2. 0000 = No valid input reference available 0001 = Input IC1 0010 = Input IC2 0011 = Input IC3 0100 = Input IC4 0101 = Input IC5 0110 = Input IC6 0111 = Input IC7 1000 = Input IC8 1001 = Input IC9 1010 = Input IC10 1011 = Input IC11 1100 = Input IC12 1101 = Input IC13 1110 = Input IC14 1111 = {unused value} Bits 3 to 0: Selected Reference (SELREF[3:0]). This real-time status field indicates the current selected reference. When T4T0 = 0 in the MCR11 register, this field indicates the selected reference for the T0 DPLL. When T4T0 = 1, it indicates the selected reference for the T4 DPLL. Note that an input clock cannot be indicated in this field if it has been marked invalid in the VALCR1 or VALCR2 register. When the T0 DPLL is in nonrevertive mode (REVERT = 0 in the MCR3 register) this field may not have the same value as the REF1[3:0] field. See Section 7.6.2. 0000 = No source currently selected 0001 = Input IC1 0010 = Input IC2 0011 = Input IC3 0100 = Input IC4 0101 = Input IC5 0110 = Input IC6 0111 = Input IC7 1000 = Input IC8 1001 = Input IC9 1010 = Input IC10 1011 = Input IC11 1100 = Input IC12 1101 = Input IC13 1110 = Input IC14 1111 = {unused value}
19-4546; Rev 9; 5/09
90 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 0 PTAB2 Priority Table Register 2 0Bh Bit 6 Bit 5 REF3[3:0] 0 0 Bit 4 0 Bit 3 0 Bit 2 Bit 1 REF2[3:0] 0 0 Bit 0 0
Bits 7 to 4: Third Highest Priority Valid Reference (REF3[3:0]). This real-time status field indicates the third highest priority validated input reference. When T4T0 = 0 in the MCR11 register, this field indicates the third highest priority reference for the T0 DPLL. When T4T0 = 1, it indicates the third highest reference for the T4 DPLL. Note that an input reference cannot be indicated in this field if it has been marked invalid in the VALCR1 or VALCR2 register. See Section 7.6.2. 0000 = Less than three valid sources available 0001 = Input IC1 0010 = Input IC2 0011 = Input IC3 0100 = Input IC4 0101 = Input IC5 0110 = Input IC6 0111 = Input IC7 1000 = Input IC8 1001 = Input IC9 1010 = Input IC10 1011 = Input IC11 1100 = Input IC12 1101 = Input IC13 1110 = Input IC14 1111 = {unused value} Bits 3 to 0: Second Highest Priority Valid Reference (REF2[3:0]). This real-time status field indicates the second highest priority validated input reference. When T4T0 = 0 in the MCR11 register, this field indicates the second highest priority reference for the T0 DPLL. When T4T0 = 1, it indicates the second highest reference for the T4 DPLL. Note that an input reference cannot be indicated in this field if it has been marked invalid in the VALCR1 or VALCR2 register. See Section 7.6.2. 0000 = Less than two valid sources available 0001 = Input IC1 0010 = Input IC2 0011 = Input IC3 0100 = Input IC4 0101 = Input IC5 0110 = Input IC6 0111 = Input IC7 1000 = Input IC8 1001 = Input IC9 1010 = Input IC10 1011 = Input IC11 1100 = Input IC12 1101 = Input IC13 1110 = Input IC14 1111 = {unused value}
19-4546; Rev 9; 5/09
91 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 0 FREQ1 Frequency Register 1 0Ch Bit 6 0 Bit 5 0 Bit 4 Bit 3 FREQ[7:0] 0 0 Bit 2 0 Bit 1 0 Bit 0 0
The FREQ1, FREQ2 and FREQ3 registers must be read consecutively. See Section 8.3. Bits 7 to 0: Current DPLL Frequency (FREQ[7:0]). The full 19-bit FREQ[18:0] field spans this register, FREQ2 and FREQ3. FREQ is a two's-complement signed integer that expresses the current frequency as an offset with respect to the master clock frequency (see Section 7.3). When T4T0 = 0 in the MCR11 register, FREQ indicates the current frequency offset of the T0 DPLL. When T4T0 = 1, FREQ indicates the current frequency offset of the T4 path. Because the value in this register field is derived from the DPLL integral path, it can be considered an average frequency with a rate of change inversely proportional to the DPLL bandwidth. If LIMINT = 1 in the MCR9 register, the value of FREQ freezes when the DPLL reaches its minimum or maximum frequency. The frequency offset in ppm is equal to FREQ[18:0] x 0.0003068. See Section 7.7.1.6. Application Note: Frequency measurements are relative, i.e., they measure the frequency of the selected reference with respect to the local oscillator. As such, when a frequency difference exists, it is difficult to distinguish whether the selected reference is off frequency or the local oscillator is off frequency. In systems with timing card redundancy, the use of two timing cards, master and slave, can address this difficulty. Both master and slave have separate local oscillators, and each measures the selected reference. These two measurements provide the necessary information to distinguish which reference is off frequency, if we make the simple assumption that at most one reference has a significant frequency deviation at any given time (i.e. a single point of failure). If both master and slave indicate a significant frequency offset, then the selected reference must be off frequency. If the master indicates a frequency offset but the slave does not, then the master's local oscillator must be off frequency. Likewise, if the slave indicates a frequency offset but the master does not, then slave's local oscillator must be off frequency. FREQ2 Frequency Register 2 0Dh Bit 6 0 Bit 5 0 Bit 4 Bit 3 FREQ[15:8] 0 0 Bit 2 0 Bit 1 0 Bit 0 0
Register Name: Register Description: Register Address: Bit 7 Name Default 0
Bits 7 to 0: Current DPLL Frequency (FREQ[15:8]). See the FREQ1 register description.
19-4546; Rev 9; 5/09
92 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 IC8 0 VALSR1 Input Clock Valid Status Register 1 0Eh Bit 6 IC7 0 Bit 5 IC6 0 Bit 4 IC5 0 Bit 3 IC4 0 Bit 2 IC3 0 Bit 1 IC2 0 Bit 0 IC1 0
Name Default
Bits 7 to 0: Input Clock Valid Status (IC8 to IC1). Each of these real-time status bits is set to 1 when the corresponding input clock is valid. An input is valid if it has no active alarms (HARD = 0, ACT = 0, LOCK = 0 in the corresponding ISR register). See also the MSR1 register and Section 7.5. 0 = Invalid 1 = Valid
Register Name: Register Description: Register Address: Bit 7 FHORDY 0
VALSR2 Input Clock Valid Status Register 2 0Fh Bit 6 SHORDY 0 Bit 5 IC14 0 Bit 4 IC13 0 Bit 3 IC12 0 Bit 2 IC11 0 Bit 1 IC10 0 Bit 0 IC9 0
Name Default
Bit 7: Fast Holdover Frequency Ready (FHORDY). This real-time status bit is set to 1 when the T0 DPLL has a holdover value that has been averaged over the 8-minute holdover averaging period. See the related latched status bit in MSR4 and Section 7.7.1.6. Bit 6: Slow Holdover Frequency Ready (SHORDY). This real-time status bit is set to 1 when the T0 DPLL has a holdover value that has been averaged over the 110-minute holdover averaging period. See the related latched status bit in MSR4 and Section 7.7.1.6. Bits 5 to 0: Input Clock Valid Status (IC14 to IC9). These bits have the same behavior as the bits in VALSR1 but for the IC9 through IC14 input clocks.
19-4546; Rev 9; 5/09
93 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 SOFT2 0 ISR1 Input Status Register 1 10h Bit 6 HARD2 1 Bit 5 ACT2 1 Bit 4 LOCK2 0 Bit 3 SOFT1 0 Bit 2 HARD1 1 Bit 1 ACT1 1 Bit 0 LOCK1 0
Name Default
Bit 7: Soft Frequency Limit Alarm for Input Clock 2 (SOFT2). This real-time status bit indicates a soft frequency limit alarm for input clock 2. If IC2 is the selected reference then SOFT2 is set to 1 when the frequency of IC2 is greater than or equal to the soft limit set in the SRLIMIT register. IF IC2 is not the selected reference then SOFT2 is set to 1 when the frequency of IC2 is greater than or equal to the soft limit set in the ILIMIT register. Soft alarms are disabled by default but can be enabled by setting SOFTEN = 1 in the MCR10 register. A soft alarm does not invalidate an input clock. See Section 7.5.1. Bit 6: Hard Frequency Limit Alarm for Input Clock 2 (HARD2). This real-time status bit indicates a hard frequency limit alarm for input clock 2. If IC2 is the selected reference then HARD2 is set to 1 when the frequency of IC2 is greater than or equal to the hard limit set in the SRLIMIT register. If IC2 is not the selected reference then HARD2 is set to 1 when the frequency of IC2 is greater than or equal to the hard limit set in the ILIMIT register. Hard alarms are enabled by default but can be disabled by setting HARDEN = 0 in the MCR10 register. A hard alarm clears the IC2 status bit in the VALSR1 register, invalidating the IC2 clock. See Section 7.5.1. Bit 5: Activity Alarm for Input Clock 2 (ACT2). This real-time status bit is set to 1 when the leaky bucket accumulator for IC2 reaches the alarm threshold specified in the LBxU register (where `x' in `LBxU' is specified in the BUCKET field of ICR2). An activity alarm clears the IC2 status bit in the VALSR1 register, invalidating the IC2 clock. See Section 7.5.2. Bit 4: Phase Lock Alarm for Input Clock 2 (LOCK2). This status bit is set to 1 if IC2 is the selected reference and the T0 DPLL cannot phase lock to IC2 within the duration specified in the PHLKTO register (default = 100 seconds). A phase lock alarm clears the IC2 status bit in VALSR1, invalidating the IC2 clock. If LKATO = 1 in MCR3 then LOCK2 is automatically cleared after a timeout period of 128 seconds. LOCK2 is a read/write bit. System software can clear LOCK2 by writing 0 to it, but writing 1 is ignored. See Section 7.7.1. Bit 3: Soft Frequency Limit Alarm for Input Clock 1 (SOFT1). This bit has the same behavior as the SOFT2 bit but for the IC1 input clock. Bit 2: Hard Frequency Limit Alarm for Input Clock 1 (HARD1). This bit has the same behavior as the HARD2 bit but for the IC1 input clock. Bit 1: Activity Alarm for Input Clock 1 (ACT1). This bit has the same behavior as the ACT2 bit but for the IC1 input clock. Bit 0: Phase Lock Alarm for Input Clock 1 (LOCK1). This bit has the same behavior as the LOCK2 bit but for the IC1 input clock.
19-4546; Rev 9; 5/09
94 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 SOFTn 0 ISR2, ISR3, ISR4, ISR5, ISR6, ISR7 Input Status Register 2, 3, 4, 5, 6, 7 11h, 12h, 13h, 14h, 15h, 16h Bit 6 HARDn 1 Bit 5 ACTn 1 Bit 4 LOCKn 0 Bit 3 SOFTm 0 Bit 2 HARDm 1 Bit 1 ACTm 1 Bit 0 LOCKm 0
Name Default
These registers have the same behavior as ISR1 but for the other input clocks, as follows: INPUT CLOCKS IC4 and IC3 IC6 and IC5 IC8 and IC7 IC10 and IC9 IC12 and IC11 IC14 and IC13 REGISTER ISR2 ISR3 ISR4 ISR5 ISR6 ISR7
19-4546; Rev 9; 5/09
95 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 FHORDY 0 MSR4 Master Status Register 4 17h Bit 6 SHORDY 0 Bit 5 MRAA 0 Bit 4 -- 0 Bit 3 IC2NO4 0 Bit 2 IC1NO4 0 Bit 1 IC2NO8 0 Bit 0 IC1NO8 0
Name Default
Bit 7: Fast Holdover Frequency Ready (FHORDY). This latched status bit is set to 1 when the T0 DPLL has a holdover value that has been averaged over the 8-minute holdover averaging period. FHORDY is cleared when written with a 1. When FHORDY is set it can cause an interrupt request on the INTREQ pin if the FHORDY interrupt enable bit is set in the IER4 register. See Section 7.7.1.6. Bit 6: Slow Holdover Frequency Ready (SHORDY). This latched status bit is set to 1 when the T0 DPLL has a holdover value that has been averaged over the 110-minute holdover averaging period. SHORDY is cleared when written with a 1. When SHORDY is set it can cause an interrupt request on the INTREQ pin if the SHORDY interrupt enable bit is set in the IER4 register. See Section 7.7.1.6. Bit 5: Multi-Register Access Aborted (MRAA). This latched status bit is set to 1 when a multi-byte access (read or write) is interrupted by another access to the device. MRAA is cleared when written with a 1. MRAA cannot cause an interrupt to occur. See Section 8.3. Bit 3: Input Clock 2 Has No 400Hz Component (IC2NO4). This latched status bit is set to 1 when the missing BPVs that indicate the 400Hz component cannot be found in a 5ms period (two 400Hz cycles). IC2NO4 is cleared when written with a 1 unless the 400Hz component is still not present. When IC2NO4 is set it can cause an interrupt request on the INTREQ pin if the IC2NO4 interrupt enable bit is set in the IER4 register. This status bit is only enabled when IC2 is configured as a composite clock receiver (MCR5:IC2SF = 0). See Section 7.11.1. Bit 2: Input Clock 1 Has No 400Hz Component (IC1NO4). This latched status bit is set to 1 when the missing BPVs that indicate the 400Hz component cannot be found in a 5ms period (two 400Hz cycles). IC1NO4 is cleared when written with a 1 unless the 400Hz component is still not present. When IC1NO4 is set it can cause an interrupt request on the INTREQ pin if the IC1NO4 interrupt enable bit is set in the IER4 register. This status bit is only enabled when IC1 is configured as a composite clock receiver (MCR5:IC1SF = 0). See Section 7.11.1. Bit 1: Input Clock 2 Has No 8kHz Component (IC2NO8). This latched status bit is set to 1 when the BPVs that indicate the 8kHz component cannot be found in the incoming signal in a 500s period (four 8kHz cycles). IC2NO8 is cleared when written with a 1 unless the 8kHz component is still not present. When IC2NO8 is set it can cause an interrupt request on the INTREQ pin if the IC2NO8 interrupt enable bit is set in the IER4 register. This status bit is only enabled when IC2 is configured as a composite clock receiver (MCR5:IC2SF = 0). See Section 7.11.1. Bit 0: Input Clock 1 Has No 8kHz Component (IC1NO8). This latched status bit is set to 1 when the BPVs that indicate the 8kHz component cannot be found in the incoming signal in a 500s period (four 8kHz cycles). IC1NO8 is cleared when written with a 1 unless the 8kHz component is still not present. When IC1NO8 is set it can cause an interrupt request on the INTREQ pin if the IC1NO8 interrupt enable bit is set in the IER4 register. This status bit is only enabled when IC1 is configured as a composite clock receiver (MCR5:IC1SF = 0). See Section 7.11.1.
19-4546; Rev 9; 5/09
96 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default (T0) Default (T4) 0 0 IPR1 Input Priority Register 1 18h Bit 6 Bit 5 PRI2[3:0] 0 1 0 0 Bit 4 1 0 Bit 3 0 0 Bit 2 Bit 1 PRI1[3:0] 0 1 0 0 Bit 0 0 0
Bits 7 to 4: Priority for Input Clock 2 (PRI2). Priority 0001 is highest; priority 1111 is lowest. When MCR11:T4T0 = 0, PRI2 configures IC2's priority for the T0 DPLL. When T4T0 = 1, PRI2 configures IC2's priority for the T4 path. See Section 7.6.1. 0000 = IC2 unavailable for selection. 0001-1111= IC2 relative priority Bits 3 to 0: Priority for Input Clock 1 (PRI1). Priority 0001 is highest; priority 1111 is lowest. When MCR11:T4T0 = 0, PRI1 configures IC1's priority for the T0 DPLL. When T4T0 = 1, PRI1 configures IC1's priority for the T4 path. See Section 7.6.1. 0000 = IC1 unavailable for selection. 0001-1111 = IC1 relative priority
Register Name: Register Description: Register Address: Bit 7 Name Default
IPR2, IPR3, IPR4, IPR5, IPR6, IPR7 Input Priority Register 2, 3, 4, 5, 6, 7 19h, 1Ah, 1Bh, 1Ch, 1Dh, 1Eh Bit 6 Bit 5 PRIn[3:0] Bit 4 Bit 3 see table Bit 2 Bit 1 PRIm[3:0] Bit 0
These registers have the same behavior as IPR1 but for the other input clocks, as follows: INPUT CLOCKS IC4 and IC3 IC6 and IC5 IC8 and IC7 IC10 and IC9 IC12 and IC11 IC14 and IC13 REGISTER IPR2 IPR3 IPR4 IPR5 IPR6 IPR7 DEFAULT (T0) 0101 0100 0111 0110 1001 1000 1011 1010 1101 1100 or 1101 0001* 1111 1110 DEFAULT (T4) 0000 0000 0111 0110 1001 1000 1011 1010 0000 0000 0000 0000
If the MASTSLV pin is low (slave mode) when RST = 0, then the default priority of IC11 is 1. When the device is in slave mode values written to PRI11[3:0] are latched, but the value read is always 0001 to indicate that input 11 is forced to have priority 1. See Section 7.9.1.
*In register IPR6, for the T0 path, if the MASTSLV pin is high (master mode) when RST = 0 then the default priority of input IC11 (PRI11) is 12.
19-4546; Rev 9; 5/09
97 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 DIVN 0 ICR1, ICR2, ICR3, ICR4, ICR5, ICR6, ICR7, ICR8, ICR9, ICR10, ICR11, ICR12, ICR13, ICR14 Input Configuration Register 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14 20h, 21h, 22h, 23h, 24h, 25h, 26h, 27h, 28h, 29h, 2Ah, 2Bh, 2Ch, 2Dh Bit 6 LOCK8K 0 Bit 5 Bit 4 BUCKET[1:0] 0 0 Bit 3 Bit 2 Bit 1 FREQ[3:0] See below Bit 0
Name Default
These registers are identical in function. ICRx is the control register for input clock ICx. Bit 7: DIVN Mode (DIVN). When DIVN is set to 1, the input clock is divided down by a programmable pre-divider. The resulting output clock is then passed to the DPLL and frequency monitor. All input clocks for which DIVN = 1 are divided by the factor specified in DIVN1 and DIVN2. When DIVN = 1 in an ICR register, the FREQ field of that register must be set to 8kHz. See Section 7.4.2.3. 0 = Disabled 1 = Enabled Bit 6: LOCK8K Mode (LOCK8K). When LOCK8K is set to 1, the input clock is divided down by a preset predivider. The resulting output clock, which is always 8kHz, is then passed to the DPLL. LOCK8K is ignored when DIVN = 1. LOCK8K is also ignored when DIVN=0 and FREQ[3:0] = 1001 (2kHz) or 1010 (4kHz). See Section 7.4.2.2. 0 = Disabled 1 = Enabled Bits 5 to 4: Leaky Bucket Configuration (BUCKET[1:0]). Each input clock has leaky bucket accumulator logic in its activity monitor. The LBxy registers at addresses 50h to 5Fh specify four different leaky bucket configurations. Any of the four configurations can be specified for the input clock. See Section 7.5.2. 00 = leaky bucket configuration 0 01 = leaky bucket configuration 1 10 = leaky bucket configuration 2 11 = leaky bucket configuration 3 Bits 3 to 0: Input Clock Nominal Frequency (FREQ[3:0]). This field specifies the input clock's nominal frequency. FREQ must be set to 0000 if DIVN = 1. See Section 7.4.2. 0000 = 8kHz 0001 = 1544kHz or 2048kHz (as determined by SONSDH bit in the MCR3 register) 0010 = 6.48MHz 0011 = 19.44MHz 0100 = 25.92MHz 0101 = 38.88MHz 0110 = 51.84MHz 0111 = 77.76MHz 1000 = 155.52MHz (only valid for IC5 and IC6) 1001 = 2kHz 1010 = 4kHz 1011 = 6312kHz 1100-1111 {unused values} FREQ[3:0] Default Values: ICR1-ICR4: 0000b ICR5-ICR10: 0011b ICR11: 0010b if MASTSLV = 0 0011b if MASTSLV = 1 ICR12-ICR14: 0001b Note that the ICR11 default value is set based on the state of the MASTSLV pin when the RST pin is asserted. See Section 7.13. 19-4546; Rev 9; 5/09 98 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 IC8 1 VALCR1 Input Clock Valid Control Register 1 30h Bit 6 IC7 1 Bit 5 IC6 1 Bit 4 IC5 1 Bit 3 IC4 1 Bit 2 IC3 1 Bit 1 IC2 1 Bit 0 IC1 1
Name Default
Bits 7 to 0: Input Clock Valid Control (IC8 to IC1). These control bits can be used to force input clocks to be considered invalid. If a clock is invalidated by one of these control bits it will not appear in the priority table in the PTAB1 and PTAB2 registers, even if the clock is otherwise valid. One key application for these control bits is to force clocks invalid that are declared invalid in the other DS3100 device of a redundant pair. Note that setting a VALCR bit low has no effect on the corresponding bit in the VALSR registers. See Sections 7.6.2 and 7.9.1. 0 = Force invalid 1 = Do not force invalid; determine validity normally VALCR2 Input Clock Valid Control Register 2 31h Bit 6 -- 0 Bit 5 IC14 1 Bit 4 IC13 1 Bit 3 IC12 1 Bit 2 IC11 1 Bit 1 IC10 1 Bit 0 IC9 1
Register Name: Register Description: Register Address: Bit 7 -- 0
Name Default
Bits 5 to 0: Input Clock Valid Control (IC14 to IC9). These bits have the same behavior as the bits in VALCR1 but for the IC9 through IC14 input clocks.
19-4546; Rev 9; 5/09
99 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 RST 0 MCR1 Master Configuration Register 1 32h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 0 Bit 1 T0STATE[2:0] 0 Bit 0 0
Name Default
Bit 7: Device Reset (RST). When this bit is high the entire device is held in reset, and all register fields, except the RST bit itself, are reset to their default states. When RST is active, the register fields with pin-programmed defaults do not latch their values from the corresponding input pins. Instead these fields are reset to the default values that were latched from the pins when the RST pin was last active. See Section 7.13. 0 = Normal operation 1 = Reset Bits 2 to 0: T0 DPLL State Control (T0STATE). This field allows the T0 DPLL state machine to be forced to a specified state. The state machine will remain in the forced state, and therefore cannot react to alarms and other events, as long as T0STATE is not equal to 000. See Section 7.7.1. 000 = Automatic (normal state machine operation) 001 = Free-run 010 = Holdover 011 = {unused value} 100 = Locked 101 = Prelocked 2 110 = Prelocked 111 = Loss-of-lock
19-4546; Rev 9; 5/09
100 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 MCR2 Master Configuration Register 2 33h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 1 Bit 2 Bit 1 T0FORCE[3:0] 1 1 Bit 0 1
Name Default
Bits 3 to 0: T0 DPLL Force Selected Reference (T0FORCE[3:0]). This field provides a way to force a specified input clock to be the selected reference for the T0 DPLL. Internally this is accomplished by forcing the clock to have the highest priority (as specified in PTAB1:REF1). In revertive mode (MCR3:REVERT = 1) the forced clock automatically becomes the selected reference (as specified in PTAB1:SELREF) as well. In nonrevertive mode, the forced clock only becomes the selected reference when the existing selected reference is invalidated or made unavailable for selection. When a reference is forced, the activity monitor and frequency monitor for that input and the T0 DPLL's loss-of-lock timeout logic all continue to operate and affect the relevant ISR, VALSR and MSR register bits. However, when the reference is declared invalid the T0 DPLL is not allowed to switch to another input clock. The T0 DPLL continues to respond to the fast activity monitor and the invalidate-on-event logic in the BITS receivers (register BCCR5) and CC receivers (register MCR5), transitioning to miniholdover in response to short-term events and to full holdover in response to longer events. See Section 7.6.3. 0000 = Automatic source selection (normal operation) 0001 = Force to IC1 0010 = Force to IC2 0011 = Force to IC3 0100 = Force to IC4 0101 = Force to IC5 0110 = Force to IC6 0111 = Force to IC7 1000 = Force to IC8 1001 = Force to IC9 1010 = Force to IC10 1011 = Force to IC11 1100 = Force to IC12 1101 = Force to IC13 1110 = Force to IC14 1111 = Automatic source selection (normal operation)
19-4546; Rev 9; 5/09
101 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 AEFSEN 1 MCR3 Master Configuration Register 3 34h Bit 6 LKATO 1 Bit 5 XOEDGE 0 Bit 4 MANHO 0 Bit 3 EFSEN 0 Bit 2 SONSDH see below Bit 1 MASTSLV see below Bit 0 REVERT 0
Name Default
Bit 7: Auto External Frame Sync Enable (AEFSEN). See Section 7.9.3. 0 = EFSEN bit (bit 3 below) enables and disables the external frame sync on the SYNC2K pin 1 = The external frame sync is enabled when EFSEN = 1 and the T0 DPLL is locked to the input clock specified in the SOURCE field of FSCR3. Bit 6: Phase Lock Alarm Timeout (LKATO). This bit controls how phase alarms on input clocks can be terminated. Phase alarms are indicated by the LOCK bits in ISR registers 0 = Phase alarms on input clocks can only be cancelled by software 1 = Phase alarms are automatically cancelled after a timeout period of 128 seconds Bit 5: Local Oscillator Edge (XOEDGE). This bit specifies the significant clock edge of the local oscillator clock signal on the REFCLK input pin. The faster edge should be selected for best jitter performance. See Section 7.3. 0 = Rising edge 1 = Falling edge Bit 4: Manual Holdover (MANHO). When this bit is set to 1 the T0 DPLL holdover frequency is set by the HOFREQ field in the HOCR1, HOCR2 and HOCR3 registers. When MANHO = 1 it has priority over any other holdover control fields. See Section 7.7.1.6. 0 = Standard holdover: holdover frequency is learned by the T0 DPLL from the selected reference 1 = Manual holdover: holdover frequency is taken from the HOFREQ field Bit 3: External Frame Sync Enable (EFSEN). When this bit is set to 1 the T0 DPLL looks for a reference frame sync pulse on the SYNC2K pin. See the AEFSEN bit description above for more information. See Section 7.9.3. 0 = Disable external frame sync; ignore SYNC2K pin 1 = Enable external frame sync on SYNC2K pin Bit 2: SONET or SDH Frequencies (SONSDH). This bit specifies the clock rate for input clocks with FREQ=0001 in the ICR registers (20h to 2Dh). During reset the default value of this bit is latched from the SONSDH pin. See Section 7.4.2. 0 = 2048kHz 1 = 1544 Hz Bit 1: Master or Slave Configuration (MASTSLV). This read-only bit indicates the state of the MASTSLV pin. This bit therefore does not have a fixed default value. To disable the master-slave pin feature and give software the ability to configure devices as either master or slave, wire the MASTSLV pin high (master mode) on both devices. See Section 7.9. 0 = Slave Mode. In this mode input clock IC11 is set to priority 1 (highest), the T0 DPLL is set to acquisition bandwidth, revertive mode is enabled, and phase build-out is disabled. 1 = Master Mode. In this mode all setting are configured by configuration registers. Bit 0: Revertive Mode (REVERT). This bit configures the T0 DPLL for revertive or non-revertive operation. (The T4 DPLL is always revertive). In revertive mode, if an input clock with a higher priority than the selected reference becomes valid, the higher-priority reference immediately becomes the selected reference. In nonrevertive mode, the higher priority reference does not immediately become the selected reference but does become the highestpriority reference in the priority table (REF1 field in the PTAB1 register). See Section 7.6.2. When the device is in slave mode (MASTSLV pin = 0) values written to this field are latched, but the value read is always 1 to indicate that the device is forced into revertive mode. See Section 7.9.1. 0 = Nonrevertive mode 1 = Revertive mode 19-4546; Rev 9; 5/09 102 of 227
DS3100 MCR4 Master Configuration Register 4 35h Bit 6 T4DFB 1 Bit 5 -- 0 Bit 4 OC89 0 Bit 3 0 Bit 2 Bit 1 T4FORCE[3:0] 0 0 Bit 0 0
Register Name: Register Description: Register Address: Bit 7 LKT4T0 0
Name Default
Bit 7: Lock T4 to T0 (LKT4T0). When this bit is set to 0 the T4 path operates independently from the T0 path. When it is set to 1 the T4 path locks to the output of the T0 DPLL, which allows the T4 path to be used to synthesize additional clock frequencies that are locked to the T0 reference. See Section 7.8.2.2. 0 = T4 path operates independently from T0 path 1 = T4 DPLL locks to the output of the T0 DPLL Bit 6: T4 Digital Feedback Mode (T4DFB). See Section 7.8.2.2. 0 = Analog feedback mode 1 = Digital feedback mode Bit 4: Source Control for Clock Outputs 8 and 9 (OC89). See Section 7.8.2.4. 0 = OC8 and OC9 generated from T4 DPLL 1 = OC8 and OC9 generated from T0 DPLL Bits 3 to 0: T4 DPLL Force Selected Reference (T4FORCE[3:0]). This field provides a way to force a specified input clock to be the selected reference for the T4 DPLL. Internally this is accomplished by forcing the clock to have the highest priority (as specified in PTAB1:REF1). Since the T4 DPLL always operates in revertive mode, the forced clock automatically becomes the selected reference (as specified in PTAB1:SELREF) as well. When a reference is forced, the activity monitor and frequency monitor for that input continue to operate and affect the relevant ISR, VALSR and MSR register bits. However, when the reference is declared invalid, the T4 DPLL is not allowed to switch to another input clock. See Section 7.6.3. 0000 = Automatic (normal operation) 0001 = Force to IC1 0010 = Force to IC2 0011 = Force to IC3 0100 = Force to IC4 0101 = Force to IC5 0110 = Force to IC6 0111 = Force to IC7 1000 = Force to IC8 1001 = Force to IC9 1010 = Force to IC10 1011 = Force to IC11 1100 = Force to IC12 1101 = Force to IC13 1110 = Force to IC14 1111 = Automatic (normal operation)
19-4546; Rev 9; 5/09
103 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 CCEDGE 0 MCR5 Master Configuration Register 5 36h Bit 6 BITERR 0 Bit 5 AMI 0 Bit 4 LOS 0 Bit 3 IC2SF 0 Bit 2 IC1SF 0 Bit 1 IC6SF 1 Bit 0 IC5SF 0
Name Default
Bit 7: Composite Clock 8kHz Edge (CCEDGE). This bit specifies the 8kHz clock edge in the incoming composite clock signals on inputs IC1 and IC2. See Section 7.11.1. 0 = The leading edge of the pulse following the BPV 1 = The leading edge of the BPV Bit 6: Increment the Activity Monitor on Bit Errors (BITERR). If this bit is set to 1, then the detection of a deviation from the one-BPV-in-eight pattern on IC1 or IC2 (in composite clock mode) is considered an irregularity by the corresponding activity monitor. The activity monitors increment their leaky bucket accumulators once for each 128ms interval in which irregularities occur. See Section 7.11.1. 0 = Bit errors do not increment the input clock activity monitors 1 = Bit errors do increment the input clock activity monitors Bit 5: Invalidate on AMI Violation (AMI). If this bit is set to 1, then the detection of a deviation from the one-BPVin-eight pattern in each of two consecutive 8-bit periods on IC1 or IC2 (in composite clock mode) automatically invalidates the offending clock. See Section 7.11.1. 0 = Do not invalidate on AMI violation 1 = Invalidate on incorrect AMI violation Bit 4: Invalidate on Loss of Signal (LOS). If this bit is set to 1, then the detection of two consecutive zeros on IC1 or IC2 (in composite clock mode) automatically invalidates the offending clock. See Section 7.11.1. 0 = Do not invalidate on LOS 1 = Invalidate on LOS Bit 3: Input Clock 2 Signal Format (IC2SF). See Section 7.11.1. 0 = AMI 64kHz composite clock on the IC2A pin 1 = CMOS/TTL on the IC2 pin Bit 2: Input Clock 1 Signal Format (IC1SF). See Section 7.11.1. 0 = AMI 64 kHz composite clock on the IC1A pin 1 = CMOS/TTL on the IC1 pin Bit 1: Input Clock 6 Signal Format (IC6SF). For backward compatibility this bit can be written to and read back, but it does not affect the IC6POS/NEG inputs pins, which are automatically accept LVDS and LVPECL signals without reconfiguration. See Section 7.4.1. 0 = LVDS compatible 1 = LVPECL compatible (default) Bit 0: Input Clock 5 Signal Format (IC5SF). For backward compatibility this bit can be written to and read back, but it does not affect the IC5POS/NEG inputs pins, which are automatically accept LVDS and LVPECL signals without reconfiguration. See Section 7.4.1. 0 = LVDS compatible (default) 1 = LVPECL compatible
19-4546; Rev 9; 5/09
104 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 IFSR Microprocessor Interface Selection Status Register 37h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 1 Bit 0 IFSEL[2:0] set by IFSEL[2:0] pins when RST = 0 Bit 2
Name Default
Bits 2 to 0: Microprocessor Interface Selection (IFSEL[2:0]). This read-only field shows the current state of the IFSEL[2:0] pins. When RST = 0 the state of the IFSEL pins is latched into the microprocessor interface control register (IFCR). After RST is brought high, the IFSEL pins are ignored by the interface control logic and can be used as general-purpose inputs whose values are shown in this register field. See Section 7.12.
Register Name: Register Description: Register Address: Bit 7 DIG2AF 0
MCR6 Master Configuration Register 6 38h Bit 6 DIG2SS see below Bit 5 DIG1SS see below Bit 4 -- 1 Bit 3 -- 1 Bit 2 -- 1 Bit 1 -- 1 Bit 0 -- 1
Name Default
Bit 7: Digital2 Alternate Frequency (DIG2AF). See Section 7.8.2.1. 0 = Digital2 frequency specified by DIG2SS and MCR7:DIG2F. 1 = Digital2 frequency is 6312kHz (must set DIG2SS = 0 and MCR7:DIG2F = 00) Bit 6: Digital2 SONET or SDH Frequencies (DIG2SS). This bit specifies whether the clock rates generated by the Digital2 clock synthesizer are multiples of 1.544MHz (SONET compatible) or multiples of 2.048MHz (SDH compatible). The specific multiple is set in the DIG2F field of the MCR7 register. When RST = 0 the default value of this bit is latched from the SONSDH pin. See Section 7.8.2.1. 0 = Multiples of 2048kHz 1 = Multiples of 1544kHz Bit 5: Digital1 SONET or SDH Frequencies (DIG1SS). This bit specifies whether the clock rates generated by the Digital1 clock synthesizer are multiples of 1544kHz (SONET compatible) or multiples of 2048kHz (SDH compatible). The specific multiple is set in the DIG1F field of the MCR7 register. When RST = 0 the default value of this bit is latched from the SONSDH pin. See Section 7.8.2.1. 0 = Multiples of 2048kHz 1 = Multiples of 1544kHz
19-4546; Rev 9; 5/09
105 of 227
DS3100 Register Name: Register Description: Register Address: MCR7 Master Configuration Register 7 39h Bit 5 Bit 4 DIG1F[1:0] 0 0 Bit 3 -- 1 Bit 2 -- 0 Bit 1 -- 0 Bit 0 -- 0
Name Default
Bit 7 Bit 6 DIG2F[1:0] 0 0
Bits 7 to 6: Digital2 Frequency (DIG2F[1:0]). This field and DIG2SS of MCR6 configure the frequency of the Digital2 clock synthesizer. See Section 7.8.2.1. DIG2SS = 1 00 = 1544kHz 01 = 3088kHz 10 = 6176kHz 11 = 12352kHz DIG2SS = 0 00 = 2048kHz 01 = 4096kHz 10 = 8192kHz 11 = 16384kHz
Bits 5 to 4: Digital1 Frequency (DIG1F[1:0]). This field and DIG1SS of MCR6 configure the frequency of the Digital1 clock synthesizer. See Section 7.8.2.1. DIG1SS = 1 00 = 1544kHz 01 = 3088kHz 10 = 6176kHz 11 = 12352kHz DIG1SS = 0 00 = 2048kHz 01 = 4096kHz 10 = 8192kHz 11 = 16384kHz
Register Name: Register Description: Register Address: Bit 7 -- 1
MCR8 Master Configuration Register 8 3Ah Bit 6 -- 1 Bit 5 OC8400 0 Bit 4 OC8NO8 0 Bit 3 OC7SF 0 1 Bit 2 Bit 1 Bit 0 OC6SF 1 0
Name Default
Bit 5: Output Clock 8, 400Hz Component Enable (OC8400). See Section 7.11.2. 0 = 400 Hz component disabled 1 = 400 Hz component enabled Bit 4: Output Clock 8, 8kHz Component Disable (OC8NO8). See Section 7.11.2. 0 = 8 kHz component enabled 1 = 8 kHz component disabled Bits 3 to 2: Output Clock 7 Control (OC7SF[1:0]). See Section 7.8.1. 00 = Output disabled 01 = 3V LVDS compatible (default) 10 = 3V LVDS compatible 11 = 3V LVDS compatible Bits 1 to 0: Clock Output 6 Control (OC6SF[1:0]). See Section 7.8.1. 00 = Output disabled 01 = 3V LVDS compatible 10 = 3V LVDS compatible (default) 11 = 3V LVDS compatible
19-4546; Rev 9; 5/09
106 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 AUTOBW 1 MCR9 Master Configuration Register 9 3Bh Bit 6 -- 1 Bit 5 -- 1 Bit 4 -- 1 Bit 3 LIMINT 1 Bit 2 PFD180 0 Bit 1 -- 1 Bit 0 -- 1
Name Default
Bit 7: Automatic Bandwidth Selection (AUTOBW). When the device is in slave mode (MASTSLV pin = 0), this field is ignored and the T0 DPLL is forced to use acquisition bandwidth. See Section 7.7.3. 0 = Always selects locked bandwidth from the T0LBW register 1 = Automatically selects either locked bandwidth (T0LBW register) or acquisition bandwidth (T0ABW register) as appropriate Bit 3: Limit Integral Path (LIMINT). When this bit is set to 1, the T0 DPLL's integral path is limited (i.e., frozen) when the DPLL reaches minimum or maximum frequency, as set by the HARDLIM field in DLIMIT1 and DLIMIT2. When the integral path is frozen, the current DPLL frequency in registers FREQ1, FREQ2 and FREQ3 is also frozen. Setting LIMINT = 1 minimizes overshoot when the DPLL is pulling in. See Section 7.7.3. 0 = Do not freeze integral path at min/max frequency 1 = Freeze integral path at min/max frequency Bit 2: 180 PFD Enable (PFD180). If TEST1:D180 = 1, then PFD180 has no effect. 0 = Use 180 phase detector (nearest-edge locking mode) 1 = Use 180 phase-frequency detector
19-4546; Rev 9; 5/09
107 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 1 MCLK1 Master Clock Frequency Adjustment Register 1 3Ch Bit 6 0 Bit 5 0 Bit 4 Bit 3 MCLKFREQ[7:0] 1 1 Bit 2 0 Bit 1 0 Bit 0 1
The MCLK1 and MCLK2 registers must be read consecutively and written consecutively. See Section 8.3. Bits 7 to 0: Master Clock Frequency Adjustment (MCLKFREQ[7:0]). The full 16-bit MCLKFREQ[15:0] field spans this register and MCLK2. MCLKFREQ is an unsigned integer that adjusts the frequency of the internal 204.8MHz master clock with respect to the frequency of the local oscillator clock on the REFCLK pin by up to +514ppm and -771ppm. The master clock adjustment has the effect of speeding up the master clock with a positive adjustment and slowing it down with a negative adjustment. For example, if the oscillator connected to REFCLK has an offset of +1ppm then the adjustment should be -1ppm to correct the offset. The formulas below translate adjustments to register values and vice versa. The default register value of 39,321 corresponds to 0ppm. See Section 7.3. MCLKFREQ[15:0] = adjustment_in_ppm / 0.0196229 + 39,321 adjustment_in_ppm = ( MCLKFREQ[15:0] - 39,321 ) x 0.0196229 MCLK2 Master Clock Frequency Adjustment Register 2 3Dh Bit 6 0 Bit 5 0 Bit 4 Bit 3 MLCKFREQ[15:8] 1 1 Bit 2 0 Bit 1 0 Bit 0 1
Register Name: Register Description: Register Address: Bit 7 Name Default 1
Bits 7 to 0: Master Clock Frequency Adjustment (MCLKFREQ[15:8]). See the MCLK1 register description.
19-4546; Rev 9; 5/09
108 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 0 HOCR1 Holdover Configuration Register 1 3Eh Bit 6 0 Bit 5 0 Bit 4 Bit 3 HOFREQ[7:0] 0 0 Bit 2 0 Bit 1 0 Bit 0 0
Bits 7 to 0: Holdover Frequency (HOFREQ[7:0]). The full 19-bit HOFREQ[18:0] field spans this register, HOCR2 and HOCR3. HOFREQ is a two's-complement signed integer, and it expresses the holdover frequency as an offset with respect to the master clock frequency (see Section 7.3). Writing this field sets the T0 DPLL's manual holdover frequency, which is used when MANHO = 1 in the MCR3 register. When HOCR3:RDAVG = 0, reading the HOFREQ field returns the manual holdover value previously written. When RDAVG = 1, reading the HOFREQ field returns the T0 DPLL's averaged frequency, either the fast average (if HOCR3:FAST = 1) or the slow average (if FAST = 0). The HOFREQ field has the same size and format as the FREQ[18:0] field (FREQ1, FREQ2 and FREQ3 registers) to allow software to read FREQ, filter the value, and then write to HOFREQ. Holdover frequency offset in ppm is equal to HOFREQ[18:0] x 0.0003068. See Section 7.7.1.6. Note: After either HOCR3:RDAVG or HOCR3:FAST is changed, system software must wait at least 50s before reading the corresponding holdover value from the HOFREQ[18:0] field. HOCR2 Holdover Configuration Register 2 3Fh Bit 6 0 Bit 5 0 Bit 4 Bit 3 HOFREQ[15:8] 0 0 Bit 2 0 Bit 1 0 Bit 0 0
Register Name: Register Description: Register Address: Bit 7 Name Default 0
Bits 7 to 0: Holdover Frequency (HOFREQ[15:8]). See the HOCR1 register description.
19-4546; Rev 9; 5/09
109 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 AVG 1 HOCR3 Holdover Configuration Register 3 40h Bit 6 FAST 0 Bit 5 RDAVG 0 Bit 4 Bit 3 MINIHO[1:0] 0 1 Bit 2 0 Bit 1 HOFREQ[18:16] 0 Bit 0 0
Name Default
See Section 8.3 for important information about writing and reading this register. Bit 7: Averaging (AVG). When this bit is set to 1 the T0 DPLL uses the averaged frequency value during holdover mode. When MANHO = 1 in the MCR3 register, this bit is ignored. See Section 7.7.1.6. 0 = Not averaged frequency; holdover frequency is either manual (MANHO = 1) or instantaneously frozen 1 = Averaged frequency (averaging rate set by the FAST bit below) Bit 6: Fast Averaging (FAST). This bit controls the averaging rate used in the T0 DPLL's frequency averager. Fast averaging has a -3dB response point of approximately 8 minutes. Slow averaging has a -3dB response point of approximately 110 minutes. See Section 7.7.1.6. 0 = Slow frequency averaging 1 = Fast frequency averaging Bit 5: Read Average (RDAVG). This bit controls which value is accessed when reading the HOFREQ field: the manual holdover frequency or the T0 DPLL's averaged frequency. This allows control software, optionally, to make use of the averager and manual holdover mode in a software-controlled holdover algorithm. See Section 7.7.1.6. 0 = Read the manual holdover frequency value previously written 1 = Read the averaged frequency Bits 4 to 3: Miniholdover Mode (MINIHO). Miniholdover is the state of the T0 DPLL where it is in the locked state but has temporarily lost its input. In miniholdover the DPLL behaves exactly the same as in holdover but with holdover frequency selected as specified by this field. See Section 7.7.1.7. 00 = frequency determined in the same way as holdover mode 01 = frequency instantaneously frozen (i.e., as if AVG = 0) 10 = frequency taken from fast averager (i.e., as if AVG = 1 and FAST = 1) 11 = frequency taken from slow averager (i.e., as if AVG = 1 and FAST = 0) Bits 2 to 0: Holdover Frequency (HOFREQ[18:16]). See the HOCR1 register description.
19-4546; Rev 9; 5/09
110 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 0 DLIMIT1 DPLL Frequency Limit Register 1 41h Bit 6 1 Bit 5 1 Bit 4 Bit 3 HARDLIM[7:0] 1 0 Bit 2 1 Bit 1 1 Bit 0 0
The DLIMIT1 and DLIMIT2 registers must be read consecutively and written consecutively. See Section 8.3. Bits 7 to 0: DPLL Hard Frequency Limit (HARDLIM[7:0]). The full 10-bit HARDLIM[9:0] field spans this register and DLIMIT2. HARDLIM is an unsigned integer that specifies the hard frequency limit or pull-in/hold-in range of the T0 DPLL. When frequency limit detection is enabled by setting FLLOL = 1 in the DLIMIT3 register, if the DPLL frequency exceeds the hard limit then the DPLL declares loss-of-lock. The hard frequency limit in ppm is HARDLIM[9:0] x 0.078. The default value is normally 9.2ppm. If external reference switching mode is enabled during reset (see Section 7.6.5), the default value is configured to 79.794ppm (3FFh). See Section 7.7.6.
Register Name: Register Description: Register Address: Bit 7 -- 0
DLIMIT2 DPLL Frequency Limit Register 2 42h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 Bit 0 HARDLIM[9:8] 0 0
Name Default
Bits 1 to 0: DPLL Hard Frequency Limit (HARDLIM[9:8]). See the DLIMIT1 register description.
19-4546; Rev 9; 5/09
111 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 IC8 0 IER1 Interrupt Enable Register 1 43h Bit 6 IC7 0 Bit 5 IC6 0 Bit 4 IC5 0 Bit 3 IC4 0 Bit 2 IC3 0 Bit 1 IC2 0 Bit 0 IC1 0
Name Default
Bits 7 to 0: Interrupt Enable for Input Clock Status Change (IC8 to IC1). Each of these bits is an interrupt enable control for the corresponding bit in the MSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt
Register Name: Register Description: Register Address: Bit 7 STATE 0
IER2 Interrupt Enable Register 2 44h Bit 6 SRFAIL 0 Bit 5 IC14 0 Bit 4 IC13 0 Bit 3 IC12 0 Bit 2 IC11 0 Bit 1 IC10 0 Bit 0 IC9 0
Name Default
Bit 7: Interrupt Enable for T0 DPLL State Change (STATE). This bit is an interrupt enable for the STATE bit in the MSR2 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 6: Interrupt Enable for Selected Reference Failed (SRFAIL). This bit is an interrupt enable for the SRFAIL bit in the MSR2 register. 0 = Mask the interrupt 1 = Enable the interrupt Bits 5 to 0: Interrupt Enable for Input Clock Status Change (IC14 to IC9). Each of these bits is an interrupt enable control for the corresponding bit in the MSR2 register. 0 = Mask the interrupt 1 = Enable the interrupt
19-4546; Rev 9; 5/09
112 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 FSMON 0 IER3 Interrupt Enable Register 3 45h Bit 6 T4LOCK 0 Bit 5 PHMON 0 Bit 4 T4NOIN 0 Bit 3 AMI2 0 Bit 2 LOS2 0 Bit 1 AMI1 0 Bit 0 LOS1 0
Name Default
Bit 7: Interrupt Enable for Frame Sync Input Monitor Alarm (FSMON). This bit is an interrupt enable for the FSMON bit in the MSR3 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 6: Interrupt Enable for T4 DPLL Lock Status Change (T4LOCK). This bit is an interrupt enable for the T4LOCK bit in the MSR3 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 5: Interrupt Enable for Phase Monitor Alarm (PHMON). This bit is an interrupt enable for the PHMON bit in the MSR3 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 4: Interrupt Enable for T4 No Valid Inputs Alarm (T4NOIN). This bit is an interrupt enable for the T4NOIN bit in the MSR3 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 3: Interrupt Enable for AMI Violation on IC2 (AMI2). This bit is an interrupt enable for the AMI2 bit in the MSR3 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 2: Interrupt Enable for LOS Error on IC2 (LOS2). This bit is an interrupt enable for the LOS2 bit in the MSR3 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 1: Interrupt Enable for AMI Violation on IC1 (AMI1). This bit is an interrupt enable for the AMI1 bit in the MSR3 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 0: Interrupt Enable for LOS Error on IC1 (LOS1). This bit is an interrupt enable for the LOS1 bit in the MSR3 register. 0 = Mask the interrupt 1 = Enable the interrupt
19-4546; Rev 9; 5/09
113 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 1 DIVN1 DIVN Register 1 46h Bit 6 1 Bit 5 1 Bit 4 Bit 3 DIVN[7:0] 1 1 Bit 2 1 Bit 1 1 Bit 0 1
The DIVN1 and DIVN2 registers must be read consecutively and written consecutively. See Section 8.3. Bits 7 to 0: DIVN Factor (DIVN[7:0]). The full 15-bit DIVN[14:0] field spans this register and DIVN2. This field contains the integer value used to divide the frequency of input clocks that are configured for DIVN mode (DIVN = 1 in registers ICR1 through ICR14). The frequency is divided by DIVN[14:0] + 1. DIVN mode supports a maximum input frequency of 155.52MHz; therefore, the maximum value of DIVN[14:0] is 19,439 (i.e., 155.52MHz / 8kHz - 1). Performance with DIVN values greater than 19,439 is undefined. See Section 7.4.2.3.
Register Name: Register Description: Register Address: Bit 7 -- 0
DIVN2 DIVN Register 2 47h Bit 6 0 Bit 5 1 Bit 4 1 Bit 3 DIVN[14:8] 1 Bit 2 1 Bit 1 1 Bit 0 1
Name Default
Bits 5 to 0: DIVN Factor (DIVN [14:8]). See the DIVN1 register description.
19-4546; Rev 9; 5/09
114 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 FMONCLK 0 MCR10 Master Configuration Register 10 48h Bit 6 SRFPIN 0 Bit 5 UFSW 0 Bit 4 EXTSW see below Bit 3 PBOFRZ 0 Bit 2 PBOEN 1 Bit 1 SOFTEN 0 Bit 0 HARDEN 1
Name Default
Bit 7: Frequency Monitor Clock Source (FMONCLK). This bit specifies the clock source for the input clock frequency monitors. 0 = T0 DPLL output 1 = Internal master clock Bit 6: SRFAIL Pin Enable (SRFPIN). When this bit is set to 1, the SRFAIL pin is enabled. When enabled the SRFAIL pin follows the state of the SRFAIL status bit in the MSR2 register. This gives the system a very fast indication of the failure of the current reference. See Section 7.5.3. 0 = SRFAIL pin disabled (low) 1 = SRFAIL pin enabled Bit 5: Ultra-Fast Switching Mode (UFSW). See Section 7.6.4. 0 = Disabled 1 = Enabled. The current reference source is disqualified after less than three missing clock cycles. Bit 4: External Reference Switching Mode (EXTSW). This bit enables external reference switching mode. In this mode, if the SRCSW pin is high the T0 DPLL is forced to lock to input IC3 (if the priority of IC3 is nonzero) or IC5 (if the priority of IC3 is zero) whether or not the selected input has a valid reference signal. If the SRCSW pin is low the device is forced to lock to input IC4 (if the priority of IC4 is nonzero) or IC6 (if the priority of IC4 is zero) whether or not the selected input has a valid reference signal. During reset the default value of this bit is latched from the SRCSW pin. This mode only controls the T0 DPLL. The T4 DPLL is not affected. See Section 7.6.5. 0 = Normal operation 1 = External switching mode Bit 3: Phase Build-Out Freeze (PBOFRZ). This bit freezes the current input-output phase relationship and does not allow further phase build-out events to occur. This bit affects phase build-out in response to input transients (Section 7.7.7.2) and phase build-out during reference switching (Section 7.7.7.3). 0 = Not frozen 1 = Frozen Bit 2: Phase Build-Out Enable (PBOEN). When this bit is set to 1 a phase build-out event occurs every time the T0 DPLL changes to a new reference, including exiting the holdover and free-run states. When this bit is set to 0, the T0 DPLL locks to the new source with zero degrees of phase difference. See Section 7.7.7. When the device is in slave mode (MASTSLV pin = 0) values written to this field are latched, but the value read is always 0 to indicate that the device is forced to have phase build-out disabled. See Section 7.9.1. 0 = Disabled 1 = Enabled Bit 1: Soft Frequency Alarm Enable (SOFTEN). This bit enables input clock frequency monitoring with the soft alarm limits set in the ILIMIT and SRLIMIT registers. Soft alarms are reported in the SOFT status bits of the ISR registers. See Section 7.5.1. 0 = Disabled 1 = Enabled Bit 0: Hard Frequency Limit Enable (HARDEN). This bit enables input clock frequency monitoring with the hard alarm limits set in the ILIMIT and SRLIMIT registers. Hard alarms are reported in the HARD status bits of the ISR registers. See Section 7.5.1. 0 = Disabled 1 = Enabled 19-4546; Rev 9; 5/09 115 of 227
DS3100 ILIMIT Input Clock Frequency Limit Register 49h Bit 6 Bit 5 SOFT[3:0] 0 1 Bit 4 0 Bit 3 0 Bit 2 Bit 1 HARD[3:0] 0 1 Bit 0 1
Register Name: Register Description: Register Address: Bit 7 Name Default 0
Bits 7 to 4: Soft Frequency Alarm Limit (SOFT[3:0]). This field is an unsigned integer that specifies the soft frequency alarm limit for all input clocks except the T0 DPLL's selected reference. The soft limit for the selected reference is specified by SRLIMIT:SOFT[3:0]. The soft alarm limit is only used for monitoring; soft alarms do not invalidate input clocks. The limit in ppm is (SOFT[3:0] + 1) x 3.81. The default limit is 11.43ppm. Soft alarms are reported in the SOFT status bits of the ISR registers. See Section 7.5.1. Bits 3 to 0: Hard Frequency Alarm Limit (HARD[3:0]). This field is an unsigned integer that specifies the hard frequency alarm limit for all input clocks except the T0 DPLL's selected reference. The hard limit for the selected reference is specified by SRLIMIT:HARD[3:0]. Hard alarms invalidate input clocks. The limit in ppm is (HARD[3:0] + 1) x 3.81. The default limit is 15.24ppm. Hard alarms are reported in the HARD status bits of the ISR registers. See Section 7.5.1.
Register Name: Register Description: Register Address: Bit 7 Name Default 0
SRLIMIT Selected Reference Frequency Limit Register 4Ah Bit 6 Bit 5 SOFT[3:0] 0 1 Bit 4 0 Bit 3 0 Bit 2 Bit 1 HARD[3:0] 0 1 Bit 0 1
Bits 7 to 4: Soft Frequency Alarm Limit (SOFT[3:0]). This field is an unsigned integer that specifies the soft frequency alarm limit for the T0 DPLL's selected reference. The soft limit for all other input clocks is specified by ILIMIT:SOFT[3:0]. The soft alarm limit is only used for monitoring; soft alarms do not invalidate input clocks. The limit in ppm is (SOFT[3:0] + 1) x 3.81. The default limit is 11.43ppm. Soft alarms are reported in the SOFT status bits of the ISR registers. See Section 7.5.1. Bits 3 to 0: Hard Frequency Alarm Limit (HARD[3:0]). This field is an unsigned integer that specifies the hard frequency alarm limit for the T0 DPLL's selected reference. The hard limit for all other input clocks is specified by ILIMIT:HARD[3:0]. Hard alarms invalidate input clocks. The limit in ppm is (HARD[3:0] + 1) x 3.81. The default limit is 15.24ppm. Hard alarms are reported in the HARD status bits of the ISR registers. See Section 7.5.1.
19-4546; Rev 9; 5/09
116 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 MCR11 Master Configuration Register 11 4Bh Bit 6 -- 0 Bit 5 -- 0 Bit 4 T4T0 0 Bit 3 0 Bit 2 Bit 1 FMEASIN[3:0] 0 0 Bit 0 0
Name Default
Bit 4: T4 or T0 Path Select (T4T0). This bit specifies which path is being accessed when reads or writes are made to the following registers: PTAB1, PTAB2, FREQ1, FREQ2, FREQ3, IPR1 through IPR7, PHASE1 and PHASE2. 0 = T0 path 1 = T4 path Bits 3 to 0: Frequency Measurement Input Select (FMEASIN[3:0]). This field specifies the input clock for the frequency measurement reported in the FMEAS register. See Section 7.5.1. 0000 = {unused value} 0001 = IC1 0010 = IC2 0011 = IC3 0100 = IC4 0101 = IC5 0110 = IC6 0111 = IC7 1000 = IC8 1001 = IC9 1010 = IC10 1011 = IC11 1100 = IC12 1101 = IC13 1110 = IC14 1111 = {unused value}
Register Name: Register Description: Register Address: Bit 7 Name Default 0
FMEAS Frequency Measurement Register 4Ch Bit 6 0 Bit 5 0 Bit 4 Bit 3 FMEAS[7:0] 0 0 Bit 2 0 Bit 1 0 Bit 0 0
Bits 7 to 0: Measured Frequency (FMEAS[7:0]). This read-only field indicates the measured frequency of the input clock specified in the FMEASIN field of the MCR11 register. FMEAS is a two's-complement signed integer that expresses the frequency as an offset with respect to the frequency monitor clock (either the internal master clock or the output of the T0 DPLL, depending on the setting of the FMONCLK bit in the MCR10 register). The measured frequency is FMEAS[7:0] x 3.81ppm. See Section 7.5.1.
19-4546; Rev 9; 5/09
117 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 FLLOL 1 DLIMIT3 DPLL Frequency Limit Register 3 4Dh Bit 6 0 Bit 5 0 Bit 4 0 Bit 3 SOFTLIM[6:0] 1 Bit 2 1 Bit 1 1 Bit 0 0
Name Default
Bit 7: Frequency Limit Loss of Lock (FLLOL). When this bit is set to 1, the T0 and T4 DPLLs internally declare loss-of-lock when their hard limits are reached. The T0 DPLL hard frequency limit is set in the HARDLIM[9:0] field in the DLIMIT1 and DLIMIT2 registers. The T4 DPLL hard frequency limit is fixed at 80ppm. See Section 7.7.6. 0 = DPLL declares loss-of-lock normally 1 = DPLL also declares loss-of-lock when the hard frequency limit is reached Bits 6 to 0: DPLL Soft Frequency Limit (SOFTLIM6:0]). This field is an unsigned integer that specifies the soft frequency limit for the T0 and T4 DPLLs. The soft limit is only used for monitoring; exceeding this limit does not cause loss-of-lock. The limit in ppm is SOFTLIM[6:0] x 0.628. The default value is 8.79ppm. When the T0 DPLL frequency exceeds the soft limit the T0SOFT status bit is set in the OPSTATE register. When the T4 DPLL frequency exceeds the soft limit the T4SOFT status bit is set in OPSTATE. See Section 7.7.6.
19-4546; Rev 9; 5/09
118 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 FHORDY 0 IER4 Interrupt Enable Register 4 4Eh Bit 6 SHORDY 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 IC2NO4 0 Bit 2 IC1NO4 0 Bit 1 IC2NO8 0 Bit 0 IC1NO8 0
Name Default
Bit 7: Interrupt Enable for Fast Holdover Frequency Ready (FHORDY). This bit is an interrupt enable for the FHORDY bit in the MSR4 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 6: Interrupt Enable for Slow Holdover Frequency Ready (SHORDY). This bit is an interrupt enable for the SHORDY bit in the MSR4 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 3: Interrupt Enable for Input Clock 2 Has No 400Hz Component (IC2NO4). This bit is an interrupt enable for the IC2NO4 bit in the MSR4 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 2: Interrupt Enable for Input Clock 1 Has No 400Hz Component (IC1NO4). This bit is an interrupt enable for the IC1NO4 bit in the MSR4 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 1: Interrupt Enable for Input Clock 2 Has No 8kHz Component (IC2NO8). This bit is an interrupt enable for the IC2NO8 bit in the MSR4 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 0: Interrupt Enable for Input Clock 1 Has No 8kHz Component (IC1NO8). This bit is an interrupt enable for the IC1NO8 bit in the MSR4 register. 0 = Mask the interrupt 1 = Enable the interrupt
19-4546; Rev 9; 5/09
119 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 0 LB0U Leaky Bucket 0 Upper Threshold Register 50h Bit 6 0 Bit 5 0 Bit 4 Bit 3 LB0U[7:0] 0 0 Bit 2 1 Bit 1 1 Bit 0 0
Bits 7 to 0: Leaky Bucket 0 Upper Threshold (LB0U[7:0]). When the leaky bucket accumulator is equal to the value stored in this field, the activity monitor declares an activity alarm by setting the input clock's ACT bit in the appropriate ISR register. Registers LB0U, LB0L, LB0S, and LB0D together specify leaky bucket configuration 0. See Section 7.5.2.
Register Name: Register Description: Register Address: Bit 7 Name Default 0
LB0L Leaky Bucket 0 Lower Threshold Register 51h Bit 6 0 Bit 5 0 Bit 4 Bit 3 LB0L[7:0] 0 0 Bit 2 1 Bit 1 0 Bit 0 0
Bits 7 to 0: Leaky Bucket 0 Lower Threshold (LB0L[7:0]). When the leaky bucket accumulator is equal to the value stored in this field, the activity monitoring logic clears the activity alarm (if previously declared) by clearing the input clock's ACT bit in the appropriate ISR register. Registers LB0U, LB0L, LB0S, and LB0D together specify leaky bucket configuration 0. See Section 7.5.2.
Register Name: Register Description: Register Address: Bit 7 Name Default 0
LB0S Leaky Bucket 0 Size Register 52h Bit 6 0 Bit 5 0 Bit 4 Bit 3 LB0S[7:0] 0 1 Bit 2 0 Bit 1 0 Bit 0 0
Bits 7 to 0: Leaky Bucket 0 Size (LB0S[7:0]). This field specifies the maximum value of the leaky bucket. The accumulator cannot increment past this value. Registers LB0U, LB0L, LB0S, and LB0D together specify leaky bucket configuration 0. See Section 7.5.2.
19-4546; Rev 9; 5/09
120 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 LB0D Leaky Bucket 0 Decay Rate Register 53h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 Bit 0 LB0D[1:0] 0 1
Name Default
Bits 1 to 0: Leaky Bucket 0 Decay Rate (LB0D[1:0]). This field specifies the decay or "leak" rate of the leaky bucket accumulator. For each period of 1, 2, 4, or 8 128ms intervals in which no irregularities are detected on the input clock, the accumulator decrements by 1. Registers LB0U, LB0L, LB0S, and LB0D together specify leaky bucket configuration 0. See Section 7.5.2. 00 = decrement every 128ms (8 units/second) 01 = decrement every 256ms (4 units/second) 10 = decrement every 512ms (2 units/second) 11 = decrement every 1024ms (1 unit/second)
19-4546; Rev 9; 5/09
121 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 0 LB1U, LB2U, LB3U Leaky Bucket 1/2/3 Upper Threshold Register 54h, 58h, 5Ch Bit 6 0 Bit 5 0 Bit 4 Bit 3 LBxU[7:0] 0 0 Bit 2 1 Bit 1 1 Bit 0 0
Bits 7 to 0: Leaky Bucket `x' Upper Threshold (LBxU[7:0]). See the LB0U register description. Registers LB1U, LB1L, LB1S, and LB1D together specify leaky bucket configuration 1. Registers LB2U, LB2L, LB2S, and LB2D together specify leaky bucket configuration 2. Registers LB3U, LB3L, LB3S, and LB3D together specify leaky bucket configuration 3.
Register Name: Register Description: Register Address: Bit 7 Name Default 0
LB1L, LB2L, LB3L Leaky Bucket 1/2/3 Lower Threshold Register 55h, 59h, 5Dh Bit 6 0 Bit 5 0 Bit 4 Bit 3 LBxL[7:0] 0 0 Bit 2 1 Bit 1 0 Bit 0 0
Bits 7 to 0: Leaky Bucket `x' Lower Threshold (LBxL[7:0]). See the LB0L register description. Registers LB1U, LB1L, LB1S, and LB1D together specify leaky bucket configuration 1. Registers LB2U, LB2L, LB2S, and LB2D together specify leaky bucket configuration 2. Registers LB3U, LB3L, LB3S, and LB3D together specify leaky bucket configuration 3.
Register Name: Register Description: Register Address: Bit 7 Name Default 0
LB1S, LB2S, LB3S Leaky Bucket 1/2/3 Size Register 56h, 5Ah, 5Eh Bit 6 0 Bit 5 0 Bit 4 Bit 3 LBxS[7:0] 0 1 Bit 2 0 Bit 1 0 Bit 0 0
Bits 7 to 0: Leaky Bucket `x' Size (LBxS[7:0]). See the LB0S register description. Registers LB1U, LB1L, LB1S, and LB1D together specify leaky bucket configuration 1. Registers LB2U, LB2L, LB2S, and LB2D together specify leaky bucket configuration 2. Registers LB3U, LB3L, LB3S, and LB3D together specify leaky bucket configuration 3.
Register Name: Register Description: Register Address: Bit 7 -- 0
LB1D, LB2D, LB3D Leaky Bucket 1/2/3 Decay Rate Register 57h, 5Bh, 5Fh Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 Bit 0 LBxD[1:0] 0 1
Name Default
Bits 1 to 0: Leaky Bucket `x' Decay Rate (LBxD[1:0]). See the LB0D register description. Registers LB1U, LB1L, LB1S, and LB1D together configure leaky bucket algorithm 1. Registers LB2U, LB2L, LB2S, and LB2D together configure leaky bucket algorithm 2. Registers LB3U, LB3L, LB3S, and LB3D together configure leaky bucket algorithm 3. 19-4546; Rev 9; 5/09 122 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 1 OCR1 Output Configuration Register 1 60h Bit 6 Bit 5 OFREQ2[3:0] 0 0 Bit 4 0 Bit 3 0 Bit 2 Bit 1 OFREQ1[3:0] 1 0 Bit 0 1
Bits 7 to 4: Output Frequency of OC2 (OFREQ2[3:0]). This field specifies the frequency of output clock OC2. The frequencies of the T0 APLL and T4 APLL are configured in the T0CR1 and T4CR1 registers. The Digital1 and Digital2 frequencies are configured in the MCR7 register. See Section 7.8.2.3. Note that if the T4 DPLL is configured for 62.5MHz (T4CR1:T4FREQ = 1001) and the T4 APLL is configured to lock to the T4 DPLL (T0CR1:T4APT0 = 0), then OFREQ2 = 1100 specifies T4 APLL frequency divided by 10 to give an output frequency of 25MHz. 0000 = Output disabled (i.e., low) 0001 = 2kHz 0010 = 8kHz 0011 = Digital2 (see Table 7-8) 0100 = Digital1 (see Table 7-8) 0101 = T0 APLL frequency divided by 48 0110 = T0 APLL frequency divided by 16 0111 = T0 APLL frequency divided by 12 1000 = T0 APLL frequency divided by 8 1001 = T0 APLL frequency divided by 6 1010 = T0 APLL frequency divided by 4 1011 = T4 APLL frequency divided by 64 1100 = T4 APLL frequency divided by 48 (or by 10, see note above) 1101 = T4 APLL frequency divided by 16 1110 = T4 APLL frequency divided by 8 1111 = T4 APLL frequency divided by 4
Bits 3 to 0: Output Frequency of OC1 (OFREQ1[3:0]). This field specifies the frequency of output clock OC1. The frequencies of the T0 APLL and T4 APLL are configured in the T0CR1 and T4CR1 registers. The Digital1 and Digital2 frequencies are configured in the MCR7 register. See Section 7.8.2.3. Note that if the T4 DPLL is configured for 62.5MHz (T4CR1:T4FREQ = 1001) and the T4 APLL is configured to lock to the T4 DPLL (T0CR1:T4APT0 = 0), then OFREQ1 = 1100 specifies T4 APLL frequency divided by 10 to give an output frequency of 25MHz. 0000 = Output disabled (i.e., low) 0001 = 2kHz 0010 = 8kHz 0011 = Digital2 (see Table 7-8) 0100 = Digital1 (see Table 7-8) 0101 = T0 APLL frequency divided by 48 0110 = T0 APLL frequency divided by 16 0111 = T0 APLL frequency divided by 12 1000 = T0 APLL frequency divided by 8 1001 = T0 APLL frequency divided by 6 1010 = T0 APLL frequency divided by 4 1011 = T4 APLL frequency divided by 64 1100 = T4 APLL frequency divided by 48 (or by 10, see note above) 1101 = T4 APLL frequency divided by 16 1110 = T4 APLL frequency divided by 8 1111 = T4 APLL frequency divided by 4
19-4546; Rev 9; 5/09
123 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 1 OCR2 Output Configuration Register 2 61h Bit 6 Bit 5 OFREQ4[3:0] 0 0 Bit 4 0 Bit 3 0 Bit 2 Bit 1 OFREQ3[3:0] 1 1 Bit 0 0
Bits 7 to 4: Output Frequency of OC4 (OFREQ4[3:0]). This field specifies the frequency of output clock OC4. The frequencies of the T0 APLL and T4 APLL are configured in the T0CR1 and T4CR1 registers. The Digital1 and Digital2 frequencies are configured in the MCR7 register. See Section 7.8.2.3. Note that if the T4 DPLL is configured for 62.5MHz (T4CR1:T4FREQ = 1001) and the T4 APLL is configured to lock to the T4 DPLL (T0CR1:T4APT0 = 0), then OFREQ4 = 1100 specifies T4 APLL frequency divided by 10 to give an output frequency of 25MHz. 0000 = Output disabled (i.e., low) 0001 = 2kHz 0010 = 8kHz 0011 = Digital2 (see Table 7-8) 0100 = Digital1 (see Table 7-8) 0101 = T0 APLL frequency divided by 48 0110 = T0 APLL frequency divided by 16 0111 = T0 APLL frequency divided by 12 1000 = T0 APLL frequency divided by 8 1001 = T0 APLL frequency divided by 6 1010 = T0 APLL frequency divided by 4 1011 = T4 APLL frequency divided by 2 1100 = T4 APLL frequency divided by 48 (or by 10, see note above) 1101 = T4 APLL frequency divided by 16 1110 = T4 APLL frequency divided by 8 1111 = T4 APLL frequency divided by 4 Bits 3 to 0: Output Frequency of OC3 (OFREQ3[3:0]). This field specifies the frequency of output clock OC3. The frequencies of the T0 APLL and T4 APLL are configured in the T0CR1 and T4CR1 registers. The Digital1 and Digital2 frequencies are configured in the MCR7 register. See Section 7.8.2.3. Note that if the T4 DPLL is configured for 62.5MHz (T4CR1:T4FREQ = 1001) and the T4 APLL is configured to lock to the T4 DPLL (T0CR1:T4APT0 = 0), then OFREQ3 = 1100 specifies T4 APLL frequency divided by 10 to give an output frequency of 25MHz. 0000 = Output disabled (i.e., low) 0001 = 2kHz 0010 = 8kHz 0011 = Digital2 (see Table 7-8) 0100 = Digital1 (see Table 7-8) 0101 = T0 APLL frequency divided by 48 0110 = T0 APLL frequency divided by 16 0111 = T0 APLL frequency divided by 12 1000 = T0 APLL frequency divided by 8 1001 = T0 APLL frequency divided by 6 1010 = T0 APLL frequency divided by 4 1011 = T4 APLL frequency divided by 64 1100 = T4 APLL frequency divided by 48 (or by 10, see note above) 1101 = T4 APLL frequency divided by 16 1110 = T4 APLL frequency divided by 8 1111 = T4 APLL frequency divided by 4
19-4546; Rev 9; 5/09
124 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 1 OCR3 Output Configuration Register 3 62h Bit 6 Bit 5 OFREQ6[3:0] 0 0 Bit 4 0 Bit 3 1 Bit 2 Bit 1 OFREQ5[3:0] 0 1 Bit 0 0
Bits 7 to 4: Output Frequency of OC6 (OFREQ6[3:0]). This field specifies the frequency of output clock output OC6. The frequencies of the T0 APLL and T4 APLL are configured in the T0CR1 and T4CR1 registers. The Digital1 and Digital2 frequencies are configured in the MCR7 register. See Section 7.8.2.3. Note that if the T4 DPLL is configured for 62.5MHz (T4CR1:T4FREQ = 1001) and the T4 APLL is configured to lock to the T4 DPLL (T0CR1:T4APT0 = 0), then OFREQ6 = 1100 specifies T4 APLL frequency divided by 10 to give an output frequency of 25MHz. 0000 = Output disabled (i.e., low) 0001 = 2kHz 0010 = 8kHz 0011 = T0 APLL frequency divided by 2 0100 = Digital1 (see Table 7-8) 0101 = T0 APLL frequency 0110 = T0 APLL frequency divided by 16 0111 = T0 APLL frequency divided by 12 1000 = T0 APLL frequency divided by 8 1001 = T0 APLL frequency divided by 6 1010 = T0 APLL frequency divided by 4 1011 = T4 APLL frequency divided by 64 1100 = T4 APLL frequency divided by 48 (or by 10, see note above) 1101 = T4 APLL frequency divided by 16 1110 = T4 APLL frequency divided by 8 1111 = T4 APLL frequency divided by 4 Bits 3 to 0: Output Frequency of OC5 (OFREQ5[3:0]). This field specifies the frequency of output clock OC5. The frequencies of the T0 APLL and T4 APLL are configured in the T0CR1 and T4CR1 registers. The Digital1 and Digital2 frequencies are configured in the MCR7 register. See Section 7.8.2.3. Note that if the T4 DPLL is configured for 62.5MHz (T4CR1:T4FREQ = 1001) and the T4 APLL is configured to lock to the T4 DPLL (T0CR1:T4APT0 = 0), then OFREQ5 = 1100 specifies T4 APLL frequency divided by 10 to give an output frequency of 25MHz. 0000 = Output disabled (i.e., low) 0001 = 2kHz 0010 = 8kHz 0011 = Digital2 (see Table 7-8) 0100 = Digital1 (see Table 7-8) 0101 = T0 APLL frequency divided by 48 0110 = T0 APLL frequency divided by 16 0111 = T0 APLL frequency divided by 12 1000 = T0 APLL frequency divided by 8 1001 = T0 APLL frequency divided by 6 1010 = T0 APLL frequency divided by 4 1011 = T4 APLL frequency divided by 2 1100 = T4 APLL frequency divided by 48 (or by 10, see note above) 1101 = T4 APLL frequency divided by 16 1110 = T4 APLL frequency divided by 8 1111 = T4 APLL frequency divided by 4
19-4546; Rev 9; 5/09
125 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 OC11EN 1 OCR4 Output Configuration Register 4 63h Bit 6 OC10EN 1 Bit 5 OC9EN 1 Bit 4 OC8EN 1 Bit 3 0 Bit 2 Bit 1 OFREQ7[3:0] 1 1 Bit 0 0
Name Default
Bit 7: OC11 Enable (OC11EN). This configuration bit enables the 2kHz output on OC11. See Section 7.8.2.5. 0 = Disabled (low) 1 = Enabled Bit 6: OC10 Enable (OC10EN). This configuration bit enables the 8kHz output on OC10. See Section 7.8.2.5. 0 = Disabled (low) 1 = Enabled Bit 5: OC9 Enable (OC9EN). This configuration bit enables the 1.544/2.048MHz output on OC9. See Section 7.8.2.4. 0 = Disabled (low) 1 = Enabled Bit 4: OC8 Enable (OC8EN). This configuration bit enables OC8 to transmit a 64kHz composite clock signal. See Sections 7.8.2.4 and 7.11.2. 0 = Disabled (high impedance) 1 = Enabled Bits 3 to 0: Output Frequency of OC7 (OFREQ7[3:0]). This field specifies the frequency of output clock output OC7. The frequencies of the T0 APLL and T4 APLL are configured in the T0CR1 and T4CR1 registers. The Digital1 and Digital2 frequencies are configured in the MCR7 register. See Section 7.8.2.3. Note that if the T4 DPLL is configured for 62.5MHz (T4CR1:T4FREQ = 1001) and the T4 APLL is configured to lock to the T4 DPLL (T0CR1:T4APT0 = 0), then OFREQ7 = 1100 sel specifies ects T4 APLL frequency divided by 10 to give an output frequency of 25MHz. 0000 = Output disabled (i.e., low) 0001 = 2kHz 0010 = 8kHz 0011 = Digital2 (see Table 7-8) 0100 = T0 APLL frequency divided by 2 0101 = T0 APLL frequency divided by 48 0110 = T0 APLL frequency divided by 16 0111 = T0 APLL frequency divided by 12 1000 = T0 APLL frequency divided by 8 1001 = T0 APLL frequency divided by 6 1010 = T0 APLL frequency divided by 4 1011 = T4 APLL frequency divided by 64 1100 = T4 APLL frequency divided by 48 (or by 10, see note above) 1101 = T4 APLL frequency divided by 16 1110 = T4 APLL frequency divided by 8 1111 = T4 APLL frequency divided by 4
19-4546; Rev 9; 5/09
126 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 T4CR1 T4 DPLL Configuration Register 1 64h Bit 6 ASQUEL 0 Bit 5 OC8DUTY 0 Bit 4 OC9SON see below Bit 3 0 Bit 2 Bit 1 T4FREQ[3:0] 0 0 Bit 0 1
Name Default
Bit 6: Auto-Squelch (ASQUEL). When outputs OC8 and OC9 are sourced from the T4 DPLL (MCR4:OC89=0), this configuration bit enables automatic squelching of OC8 and OC9 whenever T4 has no valid input references. When an output is squelched it is forced low. See Section 7.8.2.4. 0 = Disable automatic squelching 1 = Enable automatic squelching of OC8 and OC9 when T4 has no valid input references Bit 5: OC8 Duty Cycle (OC8DUTY). See Section 7.11.2. 0 = 50% duty cycle 1 = 5/8 duty cycle Bit 4: OC9 SONET/SDH (OC9SON). When MCR4:OC89 = 0, this bit controls the frequency of clock output OC9. When OC89 = 1, this bit ignored and the frequency of OC9 is controlled by the SONSDH bit in MCR3. During reset the default value of this bit is latched from the SONSDH pin. See Section 7.8.2.4. 0 = 2048kHz (SDH) 1 = 1544kHz (SONET) Bits 3 to 0: T4 DPLL Frequency (T4FREQ[3:0]). This field configures the T4 DPLL frequency. The T4 DPLL frequency can affect the frequency of the T4 APLL, which in turn affects the available output frequencies on clock outputs OC1 to OC7 (see registers OCR1 to OCR4). Optionally the T4 DPLL can be disabled and the T4 APLL can be locked to the T0 DPLL (see the T4APT0 bit in the T0CR1 register). See Section 7.8.2. 0000 = 0001 = 0010 = 0011 = 0100 = 0101 = 0110 = 0111 = 1000 = 1001 = 1010-1111 = T4 DPLL FREQUENCY Disabled 77.76MHz 24.576MHz (12 x E1) 32.768MHz (16 x E1) 37.056MHz (24 x DS1) 24.704MHz (16 x DS1) 68.736MHz (2 x E3) 44.736MHz (DS3) 25.248MHz (4 x 6312 kHz) 62.500MHz (GbE / 16) {unused values} T4 APLL FREQUENCY Depends on state of T4APT0 in T0CR1 register 311.04MHz (4 x T4 DPLL) 98.304MHz (4 x T4 DPLL) 131.072MHz (4 x T4 DPLL) 148.224MHz (4 x T4 DPLL) 98.816MHz (4 x T4 DPLL) 274.944MHz (4 x T4 DPLL) 178.944MHz (4 x T4 DPLL) 100.992MHz (4 x T4 DPLL) 250.000MHz (4 x T4 DPLL) {unused values}
19-4546; Rev 9; 5/09
127 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 T4MT0 0 T0CR1 T0 DPLL Configuration Register 1 65h Bit 6 T4APT0 0 Bit 5 0 Bit 4 T0FT4[2:0] 0 Bit 3 0 Bit 2 0 Bit 1 T0FREQ[2:0] 0 Bit 0 1
Name Default
Bit 7: T4 Measure T0 Phase (T4MT0). When this bit is set to 1 the T4 path is disabled, and the T4 phase detector is configured to measure the phase difference between the selected T0 DPLL input clock and the selected T4 DPLL input clock. See Section 7.7.10. 0 = Normal operation for the T4 path 1 = Enable T4-measure-T0-phase mode Bit 6: T4 APLL Source from T0 (T4APT0). When this bit is set to 1 the T4 output APLL locks to the T0 LF output DFS rather than the T4 forward DFS. The T0FT4[1:0] field (below) specifies the T0 DPLL frequency. See Section 7.8.2. 0 = T4 APLL locks to T4 DPLL 1 = T4 APLL locks to T0 DPLL Bits 5 to 3: T0 Frequency to T4 APLL (T0FT4[2:0]). This field specifies the frequency provided from the T0 LF output DFS to the T4 output APLL when the T4APT0 bit is set to 1. This frequency can be different than the frequency specified by T0CR1:T0FREQ. Values not listed below are unused. See Section 7.8.2. T0 DPLL FREQUENCY 24.576MHz (12 x E1) 32.768MHz (16 x E1) 37.056MHz (24 x DS1) 24.704MHz (16 x DS1) 25.248MHz (4 x 6312 kHz) T4 APLL FREQUENCY 98.304MHz (4 x T0 DPLL) 131.072MHz (4 x T0 DPLL) 148.224MHz (4 x T0 DPLL) 98.816MHz (4 x T0 DPLL) 100.992MHz (4 x T0 DPLL)
000 = 010 = 100 = 110 = 111 =
Bits 2 to 0: T0 DPLL Frequency (T0FREQ[2:0]). This field configures the T0 DPLL output frequency that is passed to the T0 Output APLL. The T0 DPLL output frequency affects the frequency of the T0 Output APLL, which in turn affects the available output frequencies on clock outputs OC1 to OC7 (see registers OCR1 to OCR4). See Section 7.8.2. 000 = 001 = 010 = 011 = 100 = 101 = 110 = 111 = T0 DPLL FREQUENCY 77.76MHz, digital feedback 77.76MHz, analog feedback 24.576MHz (12 x E1) 32.768MHz (16 x E1) 37.056MHz (24 x DS1) 24.704MHz (16 x DS1) 25.248MHz (4 x 6312 kHz) {unused value} T0 APLL FREQUENCY 311.04MHz (4 x T0 DPLL) 311.04MHz (4 x T0 DPLL) 98.304MHz (4 x T0 DPLL) 131.072MHz (4 x T0 DPLL) 148.224MHz (4 x T0 DPLL) 98.816MHz (4 x T0 DPLL) 100.992MHz (4 x T0 DPLL) {unused value}
19-4546; Rev 9; 5/09
128 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 Bit 6 -- 0 T4BW T4 Bandwidth Register 66h Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 Bit 0 T4BW[1:0] 0 0
Name Default
Bits 1 to 0: T4 DPLL Bandwidth (T4BW[1:0]). See Section 7.7.3. 00 = 18 Hz 01 = 35 Hz 10 = 70 Hz 11 = {unused value}
Register Name: Register Description: Register Address: Bit 7 -- 0 Bit 6 -- 0
T0LBW T0 Locked Bandwidth Register 67h Bit 5 -- 0 Bit 4 0 Bit 3 1 Bit 2 T0LBW[4:0] 0 Bit 1 1 Bit 0 1
Name Default
Bits 4 to 0: T0 DPLL Locked Bandwidth (T0LBW[4:0]). This field configures the bandwidth of the T0 DPLL when locked to an input clock. When AUTOBW=0 in the MCR9 register, the T0LBW bandwidth is used for acquisition and for locked operation. When AUTOBW=1, T0ABW bandwidth is used for acquisition while T0LBW bandwidth is used for locked operation. See Section 7.7.3. 00000 = 0.5 mHz 00001 = 1 mHz 00010 = 2 mHz 00011 = 4 mHz 00100 = 8 mHz 00101 = 15 mHz 00110 = 30 mHz 00111 = 60 mHz 01000 = 0.1 Hz 01001 = 0.3 Hz 01010 = 0.6 Hz 01011 = 1.2 Hz 01100 = 2.5 Hz 01101 = 4 Hz 01110 = 8 Hz 01111 = 18 Hz 10000 = 35 Hz 10001 = 70 Hz 10010 to 11111 = {unused values}
19-4546; Rev 9; 5/09
129 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 Bit 6 -- 0 T0ABW T0 Acquisition Bandwidth Register 69h Bit 5 -- 0 Bit 4 0 Bit 3 1 Bit 2 T0ABW[4:0] 1 Bit 1 1 Bit 0 1
Name Default
Bits 4 to 0: T0 DPLL Acquisition Bandwidth (T0ABW[4:0]). This field configures the bandwidth of the T0 DPLL when acquiring lock. When AUTOBW=0 in the MCR9 register, the T0LBW bandwidth is used for is used for acquisition and for locked operation. When AUTOBW=1, T0ABW bandwidth is used for acquisition while T0LBW bandwidth is used for locked operation. See Section 7.7.3. 00000 = 0.5 mHz 00001 = 1 mHz 00010 = 2 mHz 00011 = 4 mHz 00100 = 8 mHz 00101 = 15 mHz 00110 = 30 mHz 00111 = 60 mHz 01000 = 0.1 Hz 01001 = 0.3 Hz 01010 = 0.6 Hz 01011 = 1.2 Hz 01100 = 2.5 Hz 01101 = 4 Hz 01110 = 8 Hz 01111 = 18 Hz 10000 = 35 Hz 10001 = 70 Hz 10010 to 11111 = {unused values}
19-4546; Rev 9; 5/09
130 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 Bit 6 0 T4CR2 T4 Configuration Register 2 6Ah Bit 5 PD2GA8K[2:0] 0 Bit 4 1 Bit 3 -- 0 Bit 2 0 Bit 1 DAMP[2:0] 1 Bit 0 1
Name Default
Bits 6 to 4: Phase Detector 2 Gain, Analog Feedback, 8 kHz (PD2GA8K[2:0]). This field specifies the gain of the T4 phase detector 2 in analog feedback mode with an input clock of 8 kHz or less. This value is only used if automatic gain selection is enabled by setting PD2EN=1 in the T4CR3 register. Analog vs. digital feedback mode is specified in MCR4:T4DFB. See Section 7.7.5. Bits 2 to 0: Damping Factor (DAMP[2:0]). This field configures the damping factor of the T4 DPLL. Damping factor is a function of both DAMP[2:0] and the T4 DPLL bandwidth (T4BW register). The default value corresponds to a damping factor of 5. See Section 7.7.4. 001 = 010 = 011 = 100 = 101 = 18 Hz 1.2 2.5 5 5 5 35 Hz 1.2 2.5 5 10 10 70 Hz 1.2 2.5 5 10 20
000, 110 and 111 = {unused values} The gain peak for each damping factor is shown below: Damping Factor 1.2 2.5 5 10 20 Gain Peak 0.4 dB 0.2 dB 0.1 dB 0.06 dB 0.03 dB
19-4546; Rev 9; 5/09
131 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 Bit 6 0 T0CR2 T0 Configuration Register 2 6Bh Bit 5 PD2GA8K[2:0] 0 Bit 4 1 Bit 3 -- 0 Bit 2 0 Bit 1 DAMP[2:0] 1 Bit 0 1
Name Default
Bits 6 to 4: Phase Detector 2 Gain, Analog Feedback, 8 kHz (PD2GA8K[2:0]). This field specifies the gain of the T0 phase detector 2 in analog feedback mode with an input clock of 8 kHz or less. This value is only used if automatic gain selection is enabled by setting PD2EN=1 in the T0CR3 register. Analog vs. digital feedback mode is specified in T0CR1:T0FREQ[2:0]. See Section 7.7.5. Bits 2 to 0: Damping Factor (DAMP[2:0]). This field configures the damping factor of the T0 DPLL. Damping factor is a function of both DAMP[2:0] and the T0 DPLL bandwidth (T0ABW and T0LBW). The default value corresponds to a damping factor of 5. See Section 7.7.4. 001 = 010 = 011 = 100 = 101 = 4 Hz 5 5 5 5 5 8 Hz 2.5 5 5 5 5 18 Hz 1.2 2.5 5 5 5 35 Hz 1.2 2.5 5 10 10 70 Hz 1.2 2.5 5 10 20
000, 110 and 111 = {unused values} The gain peak for each damping factor is shown below: Damping Factor 1.2 2.5 5 10 20 Gain Peak 0.4 dB 0.2 dB 0.1 dB 0.06 dB 0.03 dB
19-4546; Rev 9; 5/09
132 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 PD2EN 1 Bit 6 1 T4CR3 T4 Configuration Register 3 6Ch Bit 5 PD2GA[2:0] 0 Bit 4 0 Bit 3 -- 0 Bit 2 0 Bit 1 PD2GD[2:0] 1 Bit 0 0
Name Default
Bit 7: Phase Detector 2 Gain Enable (PD2EN). When this bit is set to 1, the T4 phase detector 2 is enabled and the gain is determined by the feedback mode. In digital feedback mode, the gain is set by the PD2GD field. In analog feedback mode the gain is set by the PD2GA field if the input clock frequency is greater than 8 kHz or by the PD2GA8K field in the T4CR2 register is the input clock frequency is less than or equal to 8 kHz. Analog vs. digital feedback mode is specified in MCR4:T4DFB. See Section 7.7.5. 0 = Disable 1 = Enable Bits 6 to 4: Phase Detector 2 Gain, Analog Feedback (PD2GA[2:0]). This field specifies the gain of the T4 phase detector 2 in analog feedback mode with an input clock frequency greater than 8 kHz. This value is only used if automatic gain selection is enabled by setting PD2EN=1. Analog vs. digital feedback mode is specified in MCR4:T4DFB. See Section 7.7.5. Bits 2 to 0: Phase Detector 2 Gain, Digital Feedback (PD2GD[2:0]). This field specifies the gain of the T4 phase detector 2 in digital feedback mode. This value is only used if automatic gain selection is enabled by setting PD2EN=1. Analog vs. digital feedback mode is specified in MCR4:T4DFB. See Section 7.7.5.
19-4546; Rev 9; 5/09
133 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 PD2EN 1 Bit 6 1 T0CR3 T0 Configuration Register 3 6Dh Bit 5 PD2GA[2:0] 0 Bit 4 0 Bit 3 -- 0 Bit 2 0 Bit 1 PD2GD[2:0] 1 Bit 0 0
Name Default
Bit 7: Phase Detector 2 Gain Enable (PD2EN). When this bit is set to 1, the T0 phase detector 2 is enabled and the gain is determined by the feedback mode. In digital feedback mode, the gain is set by the PD2GD field. In analog feedback mode the gain is set by the PD2GA field if the input clock is greater than 8 kHz or by the PD2GA8K field in the T0CR2 register if the input clock frequency is less than or equal to 8 kHz. Analog vs. digital feedback mode is specified in T0CR1:T0FREQ[2:0]. See Section 7.7.5. 0 = Disable 1 = Enable Bits 6 to 4: Phase Detector 2 Gain, Analog Feedback (PD2GA[2:0]). This field specifies the gain of the T0 phase detector 2 in analog feedback mode with an input clock frequency greater than 8 kHz. This value is only used if automatic gain selection is enabled by setting PD2EN=1. Analog vs. digital feedback mode is specified in T0CR1:T0FREQ[2:0]. See Section 7.7.5. Bits 2 to 0: Phase Detector 2 Gain, Digital Feedback (PD2GD[2:0]). This field specifies the gain of the T0 phase detector 2 in digital feedback mode. This value is only used if automatic gain selection is enabled by setting PD2EN=1. Analog vs. digital feedback mode is specified in T0CR1:T0FREQ[2:0]. See Section 7.7.5.
19-4546; Rev 9; 5/09
134 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 GPIO4D 0 GPCR GPIO Configuration Register 6Eh Bit 6 GPIO3D 0 Bit 5 GPIO2D 0 Bit 4 GPIO1D 0 Bit 3 GPIO4O 0 Bit 2 GPIO3O 0 Bit 1 GPIO2O 0 Bit 0 GPIO1O 0
Name Default
Bit 7: GPIO4 Direction (GPIO4D). This bit configures the data direction for the GPIO4 pin. When GPIO4 is an input its current state can be read from GPSR:GPIO4. When GPIO4 is an output, its value is controlled by the GPIO4O configuration bit. 0 = Input 1 = Output Bit 6: GPIO3 Direction (GPIO3D). This bit configures the data direction for the GPIO3 pin. When GPIO3 is an input its current state can be read from GPSR:GPIO3. When GPIO3 is an output, its value is controlled by the GPIO3O configuration bit. 0 = Input 1 = Output Bit 5: GPIO2 Direction (GPIO2D). This bit configures the data direction for the GPIO2 pin. When GPIO2 is an input its current state can be read from GPSR:GPIO2. When GPIO2 is an output, its value is controlled by the GPIO2O configuration bit. 0 = Input 1 = Output Bit 4: GPIO1 Direction (GPIO1D). This bit configures the data direction for the GPIO1 pin. When GPIO1 is an input its current state can be read from GPSR:GPIO1. When GPI13 is an output, its value is controlled by the GPIO1O configuration bit. 0 = Input 1 = Output Bit 3: GPIO4 Output Value (GPIO4O). When GPIO4 is configured as an output (GPIO4D=1) then this bit specifies the output value. 0 = Low 1 = High Bit 2: GPIO3 Output Value (GPIO3O). When GPIO3 is configured as an output (GPIO3D=1) then this bit specifies the output value. 0 = Low 1 = High Bit 1: GPIO2 Output Value (GPIO2O). When GPIO2 is configured as an output (GPIO2D=1) then this bit specifies the output value. 0 = Low 1 = High Bit 0: GPIO1 Output Value (GPIO1O). When GPIO1 is configured as an output (GPIO1D=1) then this bit specifies the output value. 0 = Low 1 = High
19-4546; Rev 9; 5/09
135 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 Bit 6 -- 0 GPSR GPIO Status Register 6Fh Bit 5 -- 0 Bit 4 -- 0 Bit 3 GPIO4 0 Bit 2 GPIO3 0 Bit 1 GPIO2 0 Bit 0 GPIO1 0
Name Default
Bit 3: GPIO4 State (GPIO4). This bit indicates the current state of the GPIO4 pin. 0 = low 1 = high Bit 2: GPIO3 State (GPIO3). This bit indicates the current state of the GPIO3 pin. 0 = low 1 = high Bit 2: GPIO2 State (GPIO2). This bit indicates the current state of the GPIO2 pin. 0 = low 1 = high Bit 1: GPIO1 State (GPIO1). This bit indicates the current state of the GPIO1 pin. 0 = low 1 = high
19-4546; Rev 9; 5/09
136 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 0 Bit 6 0 OFFSET1 Phase Offset Register 1 70h Bit 5 0 Bit 4 Bit 3 OFFSET[7:0] 0 0 Bit 2 0 Bit 1 0 Bit 0 0
The OFFSET1 and OFFSET2 registers must be read consecutively and written consecutively. See Section 8.3. Bits 7 to 0: Phase Offset (OFFSET[7:0]). The full 16-bit OFFSET[15:0] field spans this register and the OFFSET2 register. OFFSET is a 2's-complement signed integer that specifies the desired phase offset between the output clocks and the selected reference. The phase offset in picoseconds is equal to OFFSET[15:0] * actual_internal_clock_period / 211. If the internal clock is at its nominal frequency of 77.76 MHz then the phase offset equation simplifies to OFFSET[15:0] * 6.279 ps. If, however, the DPLL is locked to a reference whose frequency is +1 ppm from ideal, for example, then the actual internal clock period is 1 ppm shorter and the phase offset is 1 ppm smaller. When the OFFSET field is written, the phase of the output clocks is automatically ramped to the new offset value to avoid loss of synchronization. To adjust the phase offset without changing the phase of the output clocks, use the recalibration process enabled by FSCR3:RECAL. The OFFSET field is ignored when phase build-out is enabled (PBOEN=1 in the MCR10 register or PMPBEN=1 in the PHMON register) and when the DPLL is not locked. See Section 7.7.8. OFFSET2 Phase Offset Register 2 71h Bit 6 0 Bit 5 0 Bit 4 Bit 3 OFFSET[15:8] 0 0 Bit 2 0 Bit 1 0 Bit 0 0
Register Name: Register Description: Register Address: Bit 7 Name Default 0
Bits 7 to 0: Phase Offset (OFFSET[15:8]). See the OFFSET1 register description.
19-4546; Rev 9; 5/09
137 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 Bit 6 -- 0 PBOFF Phase Build-Out Offset Register 72h Bit 5 0 Bit 4 0 Bit 3 Bit 2 PBOFF[5:0] 0 0 Bit 1 0 Bit 0 0
Name Default
Bits 5 to 0: Phase Build-Out Offset Register (PBOFF[5:0]). An uncertainty of up to 5 ns is introduced each time a phase build-out event occurs. This uncertainty results in a phase hit on the output. Over a large number of phase build-out events the mean error should be zero. The PBOFF field specifies a fixed offset for each phase build-out event to skew the average error toward zero. This field is a 2's complement signed integer. The offset in nanoseconds is PBOFF[5:0] * 0.101. Values greater than 1.4 ns or less than -1.4 ns may cause internal math errors and should not be used. See Section 7.7.7.5.
Register Name: Register Description: Register Address: Bit 7 FLEN 1
PHLIM1 Phase Limit Register 1 73h Bit 6 NALOL 0 Bit 5 1 1 Bit 4 -- 0 Bit 3 -- 0 Bit 2 0 Bit 1 FINELIM[2:0] 1 Bit 0 0
Name Default
Bit 7: Fine Phase Limit Enable (FLEN). This configuration bit enables the fine phase limit specified in the FINELIM[2:0] field. The fine limit must be disabled for multi-UI jitter tolerance (see PHLIM2 fields). This field controls both T0 and T4. See Section 7.7.6. 0 = Disabled 1 = Enabled Bit 6: No-Activity Loss of Lock (NALOL). The T0 and T4 DPLLs can detect that an input clock has no activity very quickly (within two clock cycles). When NALOL=0, loss-of-lock is not declared when clock cycles are missing, and nearest edge locking (180) is used when the clock recovers. This gives tolerance to missing cycles. When NALOL=1, loss-of-lock is indicated as soon as no activity is detected, and the device switches to phase/frequency locking (360). This field controls both T0 and T4. See Sections 7.5.3 and 7.7.6. 0 = No activity does not trigger loss-of-lock 1 = No activity does trigger loss-of-lock Bit 5: Leave set to 1 (test control). Bits 2 to 0: Fine Phase Limit (FINELIM[2:0]). This field specifies the fine phase limit window, outside of which loss-of-lock is declared. The FLEN bit enables this feature. The phase of the input clock has to be inside the fine limit window for two seconds before phase lock is declared. Loss-of-lock is declared immediately if the phase of the input clock is outside the phase limit window. The default value of 010 is appropriate for most situations. This field controls both T0 and T4. See Section 7.7.6. 000 = Always indicates loss of phase lock--do not use 001 = Small phase limit window, 45 to 90 010 = Normal phase limit window, 90 to 180 (default) 100, 101, 110, 111 = Proportionately larger phase limit window
19-4546; Rev 9; 5/09
138 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 CLEN 1 PHLIM2 Phase Limit Register 2 74h Bit 6 MCPDEN 0 Bit 5 USEMCPD 0 Bit 4 -- 0 Bit 3 0 Bit 2 Bit 1 COARSELIM[3:0] 1 0 Bit 0 1
Name Default
Bit 7: Coarse Phase Limit Enable (CLEN). This configuration bit enables the coarse phase limit specified in the COARSELIM[3:0] field. This field controls both T0 and T4. See Section 7.7.6. 0 = Disabled 1 = Enabled Bit 6: Multi-Cycle Phase Detector Enable (MCPDEN). This configuration bit enables the multi-cycle phase detector and allows the DPLL to tolerate large-amplitude jitter and wander. The range of this phase detector is the same as the coarse phase limit specified in the COARSELIM[3:0] field. This field controls both T0 and T4. See Section 7.7.5. 0 = Disabled 1 = Enabled Bit 5: Use Multi-Cycle Phase Detector in the DPLL Algorithm (USEMCPD). This configuration bit enables the DPLL algorithm to use the multi-cycle phase detector so that a large phase measurement drives faster DPLL pullin. When USEMCPD=0, phase measurement is limited to 360, giving slower pull-in at higher frequencies but with less overshoot. When USEMCPD=1, phase measurement is set as specified in the COARSELIM[3:0] field, giving faster pull-in. MCPDEN should be set to 1 when USEMCPD=1. This field controls both T0 and T4. See Section 7.7.5. 0 = Disabled 1 = Enabled Bits 3 to 0: Coarse Phase Limit (COARSELIM[3:0]). This field specifies the coarse phase limit and the tracking range of the multi-cycle phase detector. The CLEN bit enables this feature. If jitter tolerance greater than 0.5 UI is required and the input clock is a high frequency signal then the DPLL can be configured to track phase errors over many UI using the multi-cycle phase detector. This field controls both T0 and T4. See Section 7.7.5 and 7.7.6. 0000 = 1 UI 0001 = 3 UI 0010 = 7 UI 0011 = 15 UI 0100 = 31 UI 0101 = 63 UI 0110 = 127 UI 0111 = 255 UI 1000 = 511 UI 1001 = 1023 UI 1010 = 2047 UI 1011 = 4095 UI 1100 to 1111 = 8191 UI
19-4546; Rev 9; 5/09
139 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 NW 0 Bit 6 -- 0 PHMON Phase Monitor Register 76h Bit 5 PMEN 0 Bit 4 PMPBEN 0 Bit 3 0 Bit 2 Bit 1 PMLIM[3:0] 1 1 Bit 0 0
Name Default
Bit 7: Low-Frequency Input Clock Noise Window (NW). For 2 kHz, 4 kHz or 8 kHz input clocks, this configuration bit enables a 5% tolerance noise window centered around the expected clock edge location. Noiseinduced edges outside this window are ignored, reducing the possibility of phase hits on the output clocks. NW should be enabled only when the device is locked to an input and TEST1:D180=0. 0 = All edges are recognized by the DPLL 1 = Only edges within the 5% tolerance window are recognized by the DPLL Bit 5: Phase Monitor Enable (PMEN). This configuration bit enables the phase monitor, which measures the phase error between the input clock reference and the DPLL output. When the DPLL is set for low bandwidth, a phase transient on the input causes an immediate phase error that is gradually reduced as the DPLL tracks the input. When the measured phase error exceeds the limit set in the PMLIM field, the phase monitor declares a phase monitor alarm by setting MSR3:PHMON. See Section 7.7.7. 0 = Disabled 1 = Enabled Bit 4: Phase Monitor to Phase Build-Out Enable (PMPBEN). This bit enables phase build-out in response to phase hits on the selected reference. See Section 7.7.7. 0 = Phase monitor alarm does not trigger a phase build-out event 1 = Phase monitor alarm does trigger a phase build-out event Bits 3 to 0: Phase Monitor Limit (PMLIM[3:0]). This field is an unsigned integer that specifies the magnitude of phase error that causes a phase monitor alarm to be declared (PHMON bit in the MSR3 register). The phase monitor limit in nanoseconds is equal to (PMLIM[3:0] + 7) * 156.25, which corresponds to a range of 1094 ns to 3437 ns in 156.25 ns steps. The phase monitor is enabled by setting PMEN=1. See Section 7.7.7.
19-4546; Rev 9; 5/09
140 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 0 Bit 6 0 PHASE1 Phase Register 1 77h Bit 5 0 Bit 4 Bit 3 PHASE[7:0] 0 0 Bit 2 0 Bit 1 0 Bit 0 0
The PHASE1 and PHASE2 registers must be read consecutively. See Section 8.3. Bits 7 to 0: Current DPLL Phase (PHASE[7:0]). The full 16-bit PHASE[15:0] field spans this register and the PHASE2 register. PHASE is a 2's-complement signed integer that indicates the current value of the phase detector. The value is the output of the phase averager. When T4T0=0 in the MCR11 register, PHASE indicates the current phase of the T0 DPLL. When T4T0=1, PHASE indicates the current phase of the T4 DPLL. The averaged phase difference in degrees is equal to PHASE * 0.707. See Section 7.7.10.
Register Name: Register Description: Register Address: Bit 7 Name Default 0
PHASE2 Phase Register 2 78h Bit 6 0 Bit 5 0 Bit 4 Bit 3 PHASE[15:8] 0 0 Bit 2 0 Bit 1 0 Bit 0 0
Bits 7 to 0: Current DPLL Phase (PHASE[15:8]). See the PHASE1 register description.
Register Name: Register Description: Register Address:
PHLKTO Phase Lock Timeout Register 79h Bit 5 1 Bit 4 1 Bit 3 Bit 2 PHLKTO[5:0] 0 0 Bit 1 1 Bit 0 0
Name Default
Bit 7 Bit 6 PHLKTOM[1:0] 0 0
Bits 7 to 6: Phase Lock Timeout Multiplier (PHLKTOM[1:0]). This field is an unsigned integer that specifies the resolution of the phase lock timeout field PHLKTO[5:0]. 00 = 2 seconds 01 = 4 seconds 10 = 8 seconds 11 = 16 seconds Bits 5 to 0: Phase Lock Timeout (PHLKTO[5:0]). This field is an unsigned integer that, together with the PHLKTOM[1:0] field, specifies the length of time that the T0 DPLL attempts to lock to an input clock before declaring a phase lock alarm (by setting the corresponding LOCK bit in the ISR registers). The timeout period in seconds is PHLKTO[5:0] * 2^(PHLKTOM[1:0]+1). The state machine remains in the Pre-locked, Pre-locked 2 or Phase-lost modes for the specified time before declaring a phase alarm on the selected input. See Section 7.7.1.
19-4546; Rev 9; 5/09
141 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 2K8KSRC 0 Bit 6 -- 0 FSCR1 Frame Sync Configuration Register 1 7Ah Bit 5 -- 0 Bit 4 -- 0 Bit 3 8KINV 0 Bit 2 8KPUL 0 Bit 1 2KINV 0 Bit 0 2KPUL 0
Name Default
Bit 7: 2 kHz / 8kHz Source (2K8KSRC). This configuration bit specifies the source for the 2 kHz and 8 kHz outputs available on clock outputs OC1 through OC7. See Section 7.8.2.3. 0 = T0 DPLL 1 = T4 DPLL Bit 3: 8 kHz Invert (8KINV). When this bit is set to 1 the 8 kHz signal on clock output OC10 is inverted. See Section 7.8.2.5. 0 = OC10 not inverted 1 = OC10 inverted Bit 2: 8 kHz Pulse (8KPUL). When this bit is set to 1, the 8 kHz signal on clock output OC10 is pulsed rather than 50% duty cycle. In this mode output clock OC3 must be enabled, and the pulse width of OC10 is equal to the clock period of OC3. See Section 7.8.2.5. 0 = OC10 not pulsed; 50% duty cycle 1 = OC10 pulsed, with pulse width equal to OC3 period Bit 1: 2 kHz Invert (2KINV). When this bit is set to 1 the 2 kHz signal on clock output OC11 is inverted. See Section 7.8.2.5. 0 = OC11 not inverted 1 = OC11 inverted Bit 0: 2 kHz Pulse (2KPUL). When this bit is set to 1, the 2 kHz signal on clock output OC11 is pulsed rather than 50% duty cycle. In this mode output clock OC3 must be enabled, and the pulse width of OC11 is equal to the clock period of OC3. See Section 7.8.2.5. 0 = OC11 not pulsed; 50% duty cycle 1 = OC11 pulsed, with pulse width equal to OC3 period
19-4546; Rev 9; 5/09
142 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 INDEP 0 FSCR2 Frame Sync Configuration Register 2 7Bh Bit 6 OCN 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 Bit 0 PHASE[1:0] 0 0
Name Default
Bit 7: Independent Frame Sync and Multi-frame Sync (INDEP). When this bit is set to 0, the 8 kHz frame sync on OC10 and the 2 kHz multi-frame sync on OC11 are aligned with the other output clocks when synchronized with the SYNC2K input. When this bit is 1, the frame sync and multi-frame sync are independent of the other output clocks, and their edge position may change without disturbing the other output clocks. See Section 7.9.3. 0 = OC10 and OC11 are aligned with other output clocks; all are synchronized by the SYNC2K input 1 = OC10 and OC11 are independent of the other clock outputs; only OC10 and OC11 are synchronized by the SYNC2K input Bit 6: Sync OC-N Rates (OCN). See Section 7.9.3. 0 = SYNC2K is sampled with a 6.48 MHz resolution; the selected reference must be 6.48 MHz 1 = If the selected reference is 19.44 MHz, SYNC2K is sampled at 19.44 MHz and output alignment is to 19.44 MHz. If the selected reference is 38.88 MHz, SYNC2K is sampled at 38.88 MHz. The selected reference must be either 19.44 MHz or 38.88 MHz Bits 1 to 0: External Sync Sampling Phase. (PHASE[1:0]). This field adjusts the sampling of the SYNC2K input. Normally the falling edge of SYNC2K is aligned with the falling edge of the selected reference. All UI numbers listed below are UI of the sampling clock. See Section 7.9.3. 00 = Coincident 01 = 0.5 UI early 10 = 1 UI late 11 = 0.5 UI late
19-4546; Rev 9; 5/09
143 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 RECAL 0 FSCR3 Frame Sync Configuration Register 3 7Ch Bit 6 0 Bit 5 MONLIM[2:0] 1 Bit 4 0 Bit 3 1 Bit 2 Bit 1 SOURCE[3:0] 0 1 Bit 0 1
Name Default
Bit 7: Phase Offset Recalibration (RECAL). When set to 1 this configuration bit causes a recalibration of the phase offset between the output clocks and the selected reference. This process puts the DPLL into mini holdover, internally ramps the phase offset to zero, resets all clock dividers, ramps the phase offset to the value stored in the OFFSET registers, and then switches the DPLL out of mini holdover. Unlike simply writing the OFFSET registers, the RECAL process causes no change in the phase offset of the output clocks. RECAL is automatically reset to 0 when recalibration is complete. See Section 7.7.8. 0 = Normal operation 1 = Phase offset recalibration Bits 6 to 4: Sync Monitor Limit (MONLIM[2:0]). This field configures the sync monitor limit. When the external SYNC2K input is misaligned with respect to the OC11 output by the specified number of resampling clock cycles then a frame sync monitor alarm is declared in the FSMON bit of the OPSTATE register. See Section 7.9.3. 000 = 1 UI 001 = 2 UI 010 = 3 UI 011 = 4 UI 100 = 5 UI 101 = 6 UI 110 = 7 UI 111 = 8 UI Bits 3 to 0: Sync Reference Source (SOURCE[3:0]). The external sync reference may be associated with one of the input clocks. When automatic external frame sync is enabled (AEFSEN=1 in the MCR3 register, the SYNC2K pin is only enabled when the T0 DPLL is locked to the input clock specified by the SOURCE field. See Section 7.9.3. 0000 = {unused value} 0001 = IC1 0010 = IC2 0011 = IC3 0100 = IC4 0101 = IC5 0110 = IC6 0111 = IC7 1000 = IC8 1001 = IC9 1010 = IC10 1011 = IC11 1100 = IC12 1101 = IC13 1110 = IC14 1111 = {unused value}
19-4546; Rev 9; 5/09
144 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 INTCR Interrupt Configuration Register 7Dh Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 GPO 0 Bit 1 OD 1 Bit 0 POL 0
Name Default
Bit 2: INTREQ Pin General-Purpose Output Enable (GPO). When set to 1 this bit configures the interrupt request pin to be a general-purpose output whose value is set by the POL bit. 0 = INTREQ is used for interrupts 1 = INTREQ is a general-purpose output Bit 1: INTREQ Pin Open-Drain Enable (OD). When GPO = 0: 0 = INTREQ is driven in both inactive and active states 1 = INTREQ is open-drain, i.e., it is driven in the active state but is high impedance in the inactive state When GPO = 1: 0 = INTREQ is driven as specified by POL 1 = INTREQ is high impedance and POL has no effect Bit 0: INTREQ Pin Polarity (POL). When GPO = 0: 0 = INTREQ goes low to signal an interrupt (active low) 1 = INTREQ goes high to signal an interrupt (active high) When GPO = 1: 0 = INTREQ driven low 1 = INTREQ driven high
Register Name: Register Description: Register Address: Bit 7 Name Default 1
PROT Protection Register 7Eh Bit 6 0 Bit 5 0 Bit 4 Bit 3 PROT[7:0] 0 0 Bit 2 1 Bit 1 0 Bit 0 1
Bits 7 to 0: Protection Control (PROT[7:0]). This field can be used to protect the rest of the register set from inadvertent writes. In protected mode writes to all other registers are ignored. In single unprotected mode, one register (other than PROT) can be written, but after that write the device reverts to protected mode (and the value of PROT is internally changed to 00h). In fully unprotected mode all register can be written without limitation. See Section 7.2. 1000 0101 = Fully unprotected mode 1000 0110 = Single unprotected mode all other values = Protected mode
19-4546; Rev 9; 5/09
145 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 IFCR Microprocessor Interface Configuration Register 7Fh Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 Bit 1 Bit 0 IFSEL[2:0] reset value of IFSEL[2:0] pins
Name Default
Bits 2:0 Microprocessor Interface Selection (IFSEL[2:0]). This read-only field specifies the microprocessor interface mode. The value of this register is latched from the IFSEL[2:0] pins during reset. After reset the state of the IFSEL[2:0] pins has no effect on this register but is shown in the IFSR register. See Section 7.12. 010 = Intel bus mode (multiplexed) 011 = Intel bus mode (nonmultiplexed) 100 = Motorola mode (nonmultiplexed) 101 = SPI mode (address and data transmitted LSB first) 110 = Motorola mode (multiplexed) 111 = SPI mode (address and data transmitted MSB first) 000, 001 = {unused value}
19-4546; Rev 9; 5/09
146 of 227
DS3100
8.5
BITS Transceiver Register Definitions
The DS3100 has two identical, independent BITS transceivers, BITS1 and BITS2. The registers for BITS1 start at 80h while those for BITS2 start at 100h. The register map shown in Table 8-3 applies to both transceivers. The address offsets in the table are added to the base addresses (Table 8-1) for the BITS transceivers to form a full address. For example, the BLSR1 register in the BITS1 transceiver is located at address 080h + 1Ah = 9Ah.
Table 8-3. BITS Transceiver Register Map
Note: Register names are hyperlinks to register definitions. Underlined fields are read-only.
ADDR OFFSET 04 08 09 0A 0B 0C 10 11 12 13 18 19 1A 1B 20 21 22 23 24 25 26 27 28 29 2A 30 31 32 33 34 35 36 37 38 39 3A 3B 40 41 42 43 50 51 52 53
REGISTER BMCR BCCR1 BCCR2 BCCR3 BCCR4 BCCR5 BLCR1 BLCR2 BLCR3 BLCR4 BLIR1 BLIR2 BLSR1 BLIER1 BRMMR BTMMR BRCR1 BRCR2 BRCR3 BRCR4 BRCR5 BTCR1 BTCR2 BTCR3 BTCR4 BRIIR BRIR1 BRIR2 BRSR1 BRIER1 BRSR2 BRSR3 BRIER3 BRSR4 BRIER4 BTSR1 BTIER1 BRBCR BTBCR BRBOC BTBOC BRAF BRNAF BRSiAF BRSiNAF
BIT 7 --
BIT 6
BIT 5
BIT 4
BIT 3 --
BIT 2
BIT 1
BIT 0
-- TMODE[1:0] TCLKS[3:0] RCLKD[3:0] MCLKS MCLKFC ROUTS ROINV TMFS -- TOUTS TOINV MPS[1:0] ZEROS[1:0] LIRST -- -- -- -- TION TIMP[1:0] 0 RION RIMP[1:0] TAIS -- LLB ALB -- RFAIL OEQ UEQ RL[3:0] -- OCC SCC LOSC -- OCC SCC LOSC REN RID -- -- TEN TID -- -- SYNCT RB8ZS RFM ARC -- -- -- -- -- RHDB3 RSIGM -- -- -- -- -- -- -- -- -- TJC TFPT TCPT -- -- -- -- FBCT2 -- -- -- -- TFPT -- -- TSiS -- BRSR4 -- -- -- -- -- -- CSC[5:2,0] RAIC AISC LOSC OOFC RAIC AISC LOSC OOFC RPDV -- COFA 8ZD -- CRCRC CASRC FASRC -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- RBR -- RBD[1:0] -- SBOC -- -- -- -- -- -- Si Si 1 RAI Sa4 SiF0 SiF2 SiF4 SiF6 SiF1 SiF3 SiF5 SiF7
-- RMODE[1:0] TSYNCS[3:0] RSYNCD[3:0] RCINV ROEN RCEN RSEN TCINV TOEN TCEN TIINV BPV AIS LOS OOF -- -- -- LCS 0 LBO[2:0] RTR RMONEN RSMS[1:0] RLB TPD RPD TE -- OC SC LOS -- -- -- -- -- OC SC LOS -- OC SC LOS -- -- RRST RT1E1 -- -- TRST TT1E1 SYNCC RJC SYNCD RESYNC OOFC[1:0] RAIIE RSFRAI RCRC4 FRC SYNCD RESYNC -- -- -- RLOSC -- -- RMFS 1 -- TB8ZS TAIS TRAI FBCT1 TSFRAI TPDE TB7ZS -- TFM IBPV -- -- THDB3 TAIS TCRC4 -- -- BRSR3 BRSR1 RAI AIS LOS OOF CRC4SA CASSA FASSA RAI AIS LOS OOF RAI AIS LOS OOF 16ZD SEFE B8ZS FBE RSA1 RSA0 RCMF RAF RSA1 RSA0 RCMF RAF -- -- BC BD -- -- BC BD TPDV/TAF TMF LOTCC LOTC TPDV/TAF TMF LOTCC LOTC RBF[2:0] -- -- -- -- -- RBOC[5:0] TBOC[5:0] FAS[6:0] Sa5 Sa6 Sa7 Sa8 SiF8 SiF10 SiF12 SiF14 SiF9 SiF11 SiF13 SiF15 147 of 227
19-4546; Rev 9; 5/09
DS3100 ADDR OFFSET 54 55 56 57 58 59 5A 5B 5C 5D 60 61 62 63 64 65 66 67 68 69 6A REGISTER BRRAI BRSa4 BRSa5 BRSa6 BRSa7 BRSa8 BRMCR BRMSR BRMIER BRSSM BTAF BTNAF BTSiAF BTSiNAF BTRAI BTSa4 BTSa5 BTSa6 BTSa7 BTSa8 BTOCR BIT 7 RAIF1 Sa4F1 Sa5F1 Sa6F1 Sa7F1 Sa8F1 -- -- -- -- Si Si SiF0 SiF1 RAIF1 Sa4F1 Sa5F1 Sa6F1 Sa7F1 Sa8F1 SiAF BIT 6 RAIF3 Sa4F3 Sa5F3 Sa6F3 Sa7F3 Sa8F3 -- -- 1 SiF2 SiF3 RAIF3 Sa4F3 Sa5F3 Sa6F3 Sa7F3 Sa8F3 SiNAF BIT 5 RAIF5 Sa4F5 Sa5F5 Sa6F5 Sa7F5 Sa8F5 SSMCH[2:0] Sa8 Sa8 SSMCH[2:0] RAI SiF4 SiF5 RAIF5 Sa4F5 Sa5F5 Sa6F5 Sa7F5 Sa8F5 RAI BIT 4 RAIF7 Sa4F7 Sa5F7 Sa6F7 Sa7F7 Sa8F7 -- -- Sa4 SiF6 SiF7 RAIF7 Sa4F7 Sa5F7 Sa6F7 Sa7F7 Sa8F7 Sa4 BIT 3 RAIF9 Sa4F9 Sa5F9 Sa6F9 Sa7F9 Sa8F9 -- Sa7 Sa7 FAS[6:0] Sa5 SiF8 SiF9 RAIF9 Sa4F9 Sa5F9 Sa6F9 Sa7F9 Sa8F9 Sa5 BIT 2 BIT 1 BIT 0
RAIF11 RAIF13 RAIF15 Sa4F11 Sa4F13 Sa4F15 Sa5F11 Sa5F13 Sa5F15 Sa6F11 Sa6F13 Sa6F15 Sa7F11 Sa7F13 Sa7F15 Sa8F11 Sa8F13 Sa8F15 -- SSMF[1:0] Sa6 Sa5 Sa4 Sa6 Sa5 Sa4 SSM[3:0] Sa6 SiF10 SiF11 RAIF11 Sa4F11 Sa5F11 Sa6F11 Sa7F11 Sa8F11 Sa6 Sa7 SiF12 SiF13 RAIF13 Sa4F13 Sa5F13 Sa6F13 Sa7F13 Sa8F13 Sa7 Sa8 SiF14 SiF15 RAIF15 Sa4F15 Sa5F15 Sa6F15 Sa7F15 Sa8F15 Sa8
BITS Transceiver Register Map Color Coding BITS Global Registers BITS LIU Registers BITS DS1/E1 Framer Registers BITS DS1 BOC Controller BITS E1 Si/Sa Registers
19-4546; Rev 9; 5/09
148 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BMCR BITS Mode Configuration Register 04h Bit 6 -- 0 Bit 5 Bit 4 TMODE[1:0] 0 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 Bit 0 RMODE[1:0] 0 0
Name Default
Bits 5 to 4: Transmitter Mode Configuration (TMODE[1:0]). This field configures the operating mode of the BITS transmitter. Note that in DS1 and E1 modes the transmit formatter must also be enabled and configured for DS1 or E1. See Sections 7.10.5.2 (DS1) and 7.10.6.2 (E1) for step-by-step configuration instructions. Table 10-2 indicates the reduction in supply current when the transmitter is powered down. See Section 7.10.7.2 for write sequences that must be done when entering or leaving the 2048 kHz mode. 00 = DS1 01 = E1 10 = 2048 kHz1 11 = {unused value} Bits 1 to 0: Receiver Mode Configuration (RMODE[1:0]). This field configures the operating mode of the BITS receiver. Note that in DS1 and E1 modes the receive framer must also be enabled and configured for DS1 or E1. See Sections 7.10.5.1 (DS1) and 7.10.6.1 (E1) for step-by-step configuration instructions. Table 10-2 indicates the reduction in supply current when the receiver is powered down. Values not listed are undefined. 00 = DS1 01 = E1 10 = 2048 kHz1 11 = 6312 kHz2
Notes 1. Complies with G.703 Section 13. 2. Complies with G.703 appendix II.2 Japanese synchronization interface. 3. TMODE and RMODE can be set to different frequencies.
19-4546; Rev 9; 5/09
149 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 1 BCCR1 BITS Clock Configuration Register 1 08h Bit 6 Bit 5 TCLKS[3:0] 0 0 Bit 4 1 Bit 3 1 Bit 2 Bit 1 TSYNCS[3:0] 1 1 Bit 0 1
Bits 7 to 4: Transmit CLK Source (TCLKS[3:0]). See Figure 7-7 and Figure 7-9. This field specifies the source for the 1544 kHz or 2048 kHz clock for the Tx Clock Mux block. When one of the OCx output clocks is specified, that output clock must configured (see Section 7.8) to have a frequency of 1544 kHz (DS1 mode) or 2048 kHz (E1 mode). See Section 7.10.3. 0000 = TIN input pin 0001 = Output clock OC1 0010 = Output clock OC2 0011 = Output clock OC3 0100 = Output clock OC4 0101 = Output clock OC5 0110 = Output clock OC6 0111 = Output clock OC7 1001 = Output clock OC9 1000, 1010 - 1101 = {unused values} 1110 = RCLK from the BITS receiver 1111 = BITS master clock from the BITS master clock PLL Bits 3 to 0: Transmit SYNC Source (TSYNCS[3:0]). , See Figure 7-7 and Figure 7-9. In DS1 and E1 BITS transmitter modes, this field specifies the source of the alignment signal for the 8 kHz frame sync signal (TSYNC). In other BITS transmitter modes this field has no effect. When one of the OCx output clocks is specified, that output clock must be configured (see Section 7.8) to have a frequency of 8 kHz or an integer divider of 8 kHz and it must be frequency locked to the TCLK source specified by TCLKS[3:0]. See Section 7.10.3. 0000 = TIN input pin 0001 = Output clock OC1 0010 = Output clock OC2 0011 = Output clock OC3 0100 = Output clock OC4 0101 = Output clock OC5 0110 = Output clock OC6 0111 = Output clock OC7 1010 = Output clock OC10 1000, 1001, 1011 - 1110 = {unused values} 1111 = TCLK signal divided by 193 (DS1 mode) or 256 (E1 mode)
19-4546; Rev 9; 5/09
150 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 0 BCCR2 BITS Clock Configuration Register 2 09h Bit 6 Bit 5 RCLKD[3:0] 0 0 Bit 4 0 Bit 3 0 Bit 2 Bit 1 RSYNCD[3:0] 0 0 Bit 0 0
Bits 7 to 4: RCLK Destination (RCLKD[3:0]). This field specifies the destination for the BITS receiver's recovered clock, RCLK. For values other than 0000, the RCLKD setting must be coordinated with the configuration of the selected input clock (Section 7.4) and the BITS receiver mode (BMCR:RMODE). The RCLK signal can also be output on the RCLK pin when RCEN=1 in BCCR3. See Section 7.10.2. 0000 = No internal destination 0001 = Input clock IC1 0010 = Input clock IC2 0011 = Input clock IC3 0100 = Input clock IC4 0101 = Input clock IC5 0110 = Input clock IC6 0111 = Input clock IC7 1000 = Input clock IC8 1001 = Input clock IC9 1010 = Input clock IC10 1011 = Input clock IC11 1100 = Input clock IC12 1101 = Input clock IC13 1110 = Input clock IC14 1111 = No internal destination Bits 3 to 0: RSYNC Destination (RSYNCD[3:0]). This field specifies the destination of the RSYNC signal (Figure 7-7). In DS1 and E1 modes, RSYNC is the recovered 8 kHz frame sync. In other BITS receiver modes RSYNC is inactive and this field has no effect. The RSYNCD setting must be coordinated with the configuration of the selected input clock (Section 7.4) and the BITS receiver mode (BMCR:RMODE). See Section 7.10.2. 0000 = No internal destination 0001 = Input clock IC1 0010 = Input clock IC2 0011 = Input clock IC3 0100 = Input clock IC4 0101 = Input clock IC5 0110 = Input clock IC6 0111 = Input clock IC7 1000 = Input clock IC8 1001 = Input clock IC9 1010 = Input clock IC10 1011 = Input clock IC11 1100 = Input clock IC12 1101 = Input clock IC13 1110 = Input clock IC14 1111 = No internal destination
19-4546; Rev 9; 5/09
151 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 MCLKS 0 BCCR3 BITS Clock Configuration Register 3 0Ah Bit 6 MCLKFC 0 Bit 5 ROUTS 0 Bit 4 ROINV 0 Bit 3 RCINV 0 Bit 2 ROEN 0 Bit 1 RCEN 0 Bit 0 RSEN 0
Name Default
Bit 7: MCLK Source (MCLKS). This bit specifies the source for the master clock for both BITS transceivers. When MCLKS=0, BCCR5:MPS[1:0] must be set to 00. See Section 7.10.1. 0 = Source from 204.8 MHz master clock (divided by 100) 1 = Source from MCLK pin Bit 6: MCLK Frequency Converter (MCLKFC). This bit specifies whether or not to use the 2.048 kHz to 1.544 kHz frequency conversion PLL in the BITS master clock PLL block. See Figure 7-8 and Section 7.10.1. 0 = bypass the frequency converter PLL 1 = use the output of the frequency converter PLL Bit 5: ROUT Source (ROUTS). This field specifies the signal source for the ROUT output pin, either RSYNC or RMFSYNC (see Figure 7-7). In DS1 and E1 modes, the RSYNC signal is the received 8 kHz frame sync, and the RMFSYNC signal is the receive multiframe sync, with E1 multiframe type specified by BRCR5:RMFS. In 2048 kHz and 6312 kHz modes, RSYNC is held low. See Section 7.10.2. 0 = RSYNC signal 1 = RMFSYNC signal Bit 4: ROUT Invert (ROINV). When ROEN=1, this bit specifies the polarity of ROUT. When ROEN=0, the ROUT pin can function as a general-purpose output controlled by this bit. See Section 7.10.2. ROEN=0 ROEN=1 0 = Normal: ROUT normally low, pulses high 0 = ROUT pin forced low 1 = Inverted ROUT normally high, pulses low 1 = ROUT pin forced high Bit 3: RCLK Invert (RCINV). When RCEN=1, this bit specifies the RCLK edge on which data is updated on the RSER pin (DS1 and E1 modes only). When RCEN=0, the RCLK pin can function as a general-purpose output pin whose value is specified by this bit. See Sections 7.10.5.1 and 7.10.6.1. RCEN=0 RCEN=1 0 = Normal: RSER updated on the rising edge of RCLK 0 = RCLK pin forced low 1 = Inverted: RSER updated on the falling edge of RCLK 1 = RCLK pin forced high Bit 2: ROUT Enable (ROEN). This bit enables/disables the ROUT output pin. When enabled, ROUT presents the signal specified by BCCR3:ROUTS. When disabled, ROUT can function as a general-purpose output controlled by the ROINV configuration bit. See Section 7.10.2. 0 = Disabled 1 = Enabled Bit 1: RCLK Enable (RCEN). This bit enables/disables the RCLK output pin. When enabled, RCLK presents the recovered clock from the BITS receiver. When disabled, RCLK can function as a general-purpose output controlled by the RCINV configuration bit. See Section 7.10.2. 0 = Disabled 1 = Enabled Bit 0: RSER Enable (RSEN). This bit enables/disables the RSER output pin. In DS1 and E1 receiver modes (BMCR:RMODE=0x), RSER presents the entire received data stream, both payload and overhead. In all other BITS receiver modes RSER is disabled and this bit has no effect. See Section 7.10.2. 0 = Disabled (low) 1 = Enabled
19-4546; Rev 9; 5/09
152 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 TMFS 0 BCCR4 BITS Clock Configuration Register 4 0Bh Bit 6 -- 0 Bit 5 TOUTS 0 Bit 4 TOINV 0 Bit 3 TCINV 0 Bit 2 TOEN 0 Bit 1 TCEN 0 Bit 0 TIINV 0
Name Default
Bit 7: Transmit Multiframe Sync Source (TMFS). In DS1 and E1 modes, this field specifies the source of the transmit multiframe signal (TMFSYNC). In other BITS transmitter modes this field has no effect. When the TIN pin is specified, the signal on TIN must be frequency locked to the TCLK source specified by BCCR1:TCLKS[3:0]. See Section 7.10.3. 0 = TSYNC signal divided by 12 (DS1 SF), 24 (DS1 ESF), or 16 (E1) 1 = TIN input pin Bit 5: TOUT Source (TOUTS). This field specifies the signal source for the TOUT output pin. See Figure 7-7. In DS1 and E1 modes, the TSYNC signal is the transmit 8 kHz frame sync, and the TMFSYNC signal is the transmit multiframe sync. In other BITS transmitter modes this bit has no effect. See Section 7.10.3 0 = TSYNC signal 1 = TMFSYNC signal Bit 4: TOUT Invert (TOINV). See Section 7.10.3. 0 = Normal: TOUT normally low, pulses high 1 = Inverted: TOUT normally high, pulses low Bit 3: TCLK Invert (TCINV). Specifies the TCLK clock edge on which data is sampled from TSER and TIN. This bit only has an effect in DS1 and E1 BITS transmitter modes (BMCR:TMODE=0x). See Sections 7.10.5.2 and 7.10.6.2. 0 = Normal: TSER and TIN updated on the falling edge of TCLK 1 = Inverted: TSER and TIN updated on the rising edge of TCLK Bit 2: TOUT Enable (TOEN). This bit enables/disables the TOUT output pin. When enabled, TOUT presents the signal specified by TOUTS. In 2048 kHz mode this bit has no effect, and TOUT remains low. See Section 7.10.3. 0 = Disabled (low) 1 = Enabled Bit 1: TCLK Enable (TCEN). This bit enables/disables the TCLK output pin. See Section 7.10.3. 0 = Disabled (low) 1 = Enabled Bit 0: TIN Invert (TIINV). When high See Section 7.10.3. 0 = Normal: TIN normally low, pulses high 1 = Inverted: TIN normally high, pulses low
19-4546; Rev 9; 5/09
153 of 227
DS3100 Register Name: Register Description: Register Address: BCCR5 BITS Clock Configuration Register 5 0Ch Bit 5 Bit 4 ZEROS[1:0] 0 0 Bit 3 BPV 0 Bit 2 AIS 0 Bit 1 LOS 0 Bit 0 OOF 0
Name Default
Bit 7 Bit 6 MPS[1:0] 0 0
Bits 7 to 6: MCLK Prescaler (MPS[1:0]). This field configures the divider in the MCLK prescaler block. When BCCR3:MCLKS=0, MPS[1:0] must be set to 00. See Figure 7-8 and Section 7.10.1. 00 = Divide by 1 (pass through MCLK signal unchanged) 01 = Divide by 2 10 = Divide by 4 11 = Divide by 8 Bits 5 to 4: Squelch and Increment on Zeros (ZEROS[1:0]). If this field is set to a non-zero value in any mode and the specified number of consecutive zeros are detected (prior to B8ZS/HDB3 decoding), then the BITS receiver automatically squelches its output clock. The resulting lack of clock edges increments the activity monitor for the input clock connected to the BITS receiver (as specified in BCCR2:RCLKD). See Sections 7.5 and 7.10.2. When ultra-fast switching is enabled (MCR10:UFSW = 1), squelching the clock causes that input clock to be immediately invalidated. See section 7.6.4. 00 = Do not invalidate on zeros 01 = Invalidate on a string of 4 consecutive zeros 10 = Invalidate on a string of 8 consecutive zeros 11 = Invalidate on a string of 16 consecutive zeros Bit 3: Increment the Activity Monitor on BPVs (BPV). If this bit is set to 1 in DS1 or E1 receiver modes then the detection of an unexpected BPV is considered an irregularity by the activity monitors for the ICx input clocks to which RCLK and RSYNC are connected (as specified in BCCR2:RCLKD and RSYNCD). The activity monitors increment their leaky bucket accumulators once for each 128-ms interval in which irregularities occur. An unexpected BPV is one that is not part of a valid B8ZS or HDB3 codeword. If this bit is set to 1 in 2048 kHz mode then the detection of an unexpected BPV or zero is considered an irregularity by the relevant activity monitors. In 6312 kHz receiver mode this bit has no effect. See Sections 7.5 and 7.10.2. 0 = BPVs do not increment the input clock activity monitors 1 = BPVs do increment the input clock activity monitors Bit 2: Invalidate on Alarm Indication Signal (AIS). If this bit is set to 1 in DS1 and E1 receiver modes and AIS (i.e. unframed all ones) is detected in the receive data stream, then the device automatically invalidates the ICx input clocks to which RCLK and RSYNC are connected (as specified in BCCR2:RCLKD and RSYNCD). Invalidation means the corresponding bit in the VALSR registers is set to 0. See Table 7-16 (DS1) and Table 7-17 (E1) for AIS set and clear criteria. In other receiver modes this bit has no effect. See Sections 7.5 and 7.10.2. 0 = Do not invalidate on AIS 1 = Invalidate on AIS Bit 1: Invalidate on Loss of Signal (LOS). If this bit is set to 1 in any receiver mode and the receiver declares loss of signal (BLIR1:LOS = 1), then the device automatically invalidates the ICx input clocks to which RCLK and RSYNC are connected (as specified in BCCR2:RCLKD and RSYNCD). Invalidation means the corresponding bit in the VALSR registers is set to 0. Regardless of the setting of this bit, RCLK and RSYNC are squelched when the receiver declares LOS. See Sections 7.5 and 7.10.2. 0 = Do not invalidate on LOS 1 = Invalidate on LOS Bit 0: Invalidate on Out of Frame (OOF). If this bit is set to 1 in DS1 and E1 receiver modes and the receive framer declares out-of-frame (BRIR1:OOF=1), then the device automatically invalidates the ICx input clocks to which RCLK and RSYNC are connected (as specified in BCCR2:RCLKD and RSYNCD). Invalidation means the corresponding bit in the VALSR registers is set to 0. In other receiver modes this bit has no effect. See Sections 7.5 and 7.10.2. 0 = Do not invalidate on OOF 1 = Invalidate on OOF 19-4546; Rev 9; 5/09 154 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 LIRST 0 BLCR1 BITS LIU Configuration Register 1 10h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 -- 0 Bit 0 LCS 1
Name Default
Bit 7: Line Interface Reset (LIRST). A zero-to-one transition resets the clock recovery state machine. Normally this bit is only toggled after power-up. LIRST must be cleared and set again for a subsequent reset. Bit 0: LOS Criteria Selection (LCS). In E1 mode this bit specifies the loss of signal criteria to use. In DS1 mode, LOS criteria is always based on ANSTI T1.231, and this bit has no effect. See Section 7.10.4.1. 0 = G.775 criteria (192-bit window) 1 = ETSI 300 233 criteria (2048-bit window)
Register Name: Register Description: Register Address: Bit 7 -- 0
BLCR2 BITS LIU Configuration Register 2 11h Bit 6 TION 0 Bit 5 Bit 4 TIMP[1:0] 0 0 Bit 3 0 0 Bit 2 0 Bit 1 LBO[2:0] 0 Bit 0 0
Name Default
Bit 6: Transmitter Impedance On (TION). See Section 7.10.4.2. 0 = Disable internal transmitter termination 1 = Enable internal transmitter termination with impedance set by TIMP[1:0] Bits 5 to 4: Transmit Impedance (TIMP[1:0]). This field specifies the transmit cable impedance. The actual transmit cable impedance must be specified by this field for proper operation, regardless of the value of the TION bit. For J1 applications, use 110. See Section 7.10.4.1.6. 00 = 75 01 = 100 10 = 110 11 = 120 Bit 3: Leave set to zero (test control). Bits 2 to 0: Transmitter Line Build-Out (LBO[2:0]). This field specifies the line build-out setting for the BITS transmitter. Values not listed are undefined. This field is ignored in BITS modes other than DS1 and E1. See Section 7.10.4.1.6. DS1 Mode 000 = DSX-1 (0 to 133 feet) / 0 dB CSU 001 = DSX-1 (133 to 266 feet) 010 = DSX-1 (266 to 399 feet) 011 = DSX-1 (399 to 533 feet) 100 = DSX-1 (533 to 655 feet) 101 = -7.5 dB CSU 110 = -15 dB CSU 111 = -22.5 dB CSU E1 Mode 000 = 75, nominal voltage = 2.37V 001 = 120, nominal voltage = 3.0V 19-4546; Rev 9; 5/09 155 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 0 0 BLCR3 BITS LIU Configuration Register 3 12h Bit 6 RION 0 Bit 5 Bit 4 RIMP[1:0] 0 0 Bit 3 RTR 0 Bit 2 RMONEN 0 Bit 1 Bit 0 RSMS[1:0] 0 0
Name Default
Bit 7: Leave set to zero (test control). Bit 6: Receiver Impedance On (RION). See Section 7.10.4.1. 0 = Disable internal receiver termination, RTIP/RRING are high-impedance 1 = Enable internal receiver termination with impedance set by RIMP[1:0] Bits 5 to 4: Receive Impedance (RIMP[1:0]). This field specifies the receive cable impedance. When internal termination impedance is enabled (RION=1), the internal impedance is set to the value specified by this field. When internal termination impedance is disabled (RION=0), the actual receive cable impedance must be specified by this field for proper operation. See Section 7.10.4.1. 00 = 75 01 = 100 10 = 110 11 = 120 Bit 3: Receiver Turns Ratio (RTR). See Section 7.10.4.1. 0 = Receiver transformer turns ratio is 1:1 1 = Receiver transformer turns ratio is 2:1. This option should only be used in short haul applications. Bit 2 : Receiver Monitor Mode Enable (RMONEN). In DS1, E1 and 2048 kHz modes this field enables and disables monitor mode. In 6312 kHz mode, this field has no effect. See Section 7.10.4.1. 0 = Disable receive monitor mode 1 = Enable receiver monitor mode. Flat gain is added with the maximum sensitivity. The receiver sensitivity is determined by RSMS[1:0]. Bits 1 to 0: Receiver Sensitivity / Monitor Select (RSMS[1:0]. In DS1, E1 and 2048 kHz modes, this field controls the receiver sensitivity level and additional gain in monitoring applications. The monitor mode (RMONEN=1) adds flat gain to compensate for the signal loss caused by isolation resistors. In 6312 kHz mode this field has no effect. See Section 7.10.4.1. RECEIVER MONITOR MODE GAIN (dB) 0 0 0 0 14 20 26 32 DS1/E1 RECEIVER SENSITIVITY (MAX CABLE LOSS ALLOWED) (dB) 12 18 30 36 (DS1), 43 (E1) 30 22.5 17.5 12
RMONEN 0 0 0 0 1 1 1 1
RSMS [1:0] 00 01 10 11 00 01 10 11
In 2048kHz mode, the receiver sensitivity numbers are approximately 8dB lower than the E1 values shown in the table.
19-4546; Rev 9; 5/09
156 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 TAIS 0 BLCR4 BITS LIU Configuration Register 4 13h Bit 6 -- 0 Bit 5 LLB 0 Bit 4 ALB 0 Bit 3 RLB 0 Bit 2 TPD 1 Bit 1 RPD 1 Bit 0 TE 0
Name Default
Bit 7: Transmit AIS (TAIS). This field is ignored in BITS modes other than DS1 and E1. See Section 7.10.4.1.6. 0 = Transmit data normally 1 = Transmit AIS (unframed all-ones) on TTIP and TRING Bit 5: Local Loopback (LLB). Local loopback loops the output of the transmit formatter back to the input of the receive framer. During this loopback transmit data propagates through the transmit side of the BITS transceiver as it normally would, but the recovered clock and data from the LIU receiver is ignored. See Figure 7-7 for the exact loopback path. 0 = Disabled 1 = Enabled Bit 4: Analog Loopback (ALB). Analog loopback loops the output of the LIU transmitter back to the input of the LIU receiver. During this loopback transmit data propagates through the transmit side of the BITS transceiver as it normally would, but the incoming signal on RTIP/RRING is ignored. See Figure 7-7 for the exact loopback path. 0 = Disabled 1 = Enabled Bit 3: Remote Loopback (RLB). Remote loopback loops the output of the LIU receiver back to the input of the LIU transmitter. During this loopback received data propagates through the receive side of the BITS transceiver as it normally would, but the output from the transmit formatter is ignored. See Figure 7-7 for the exact loopback path. (Note: A remote loopback of the recovered clock can also be accomplished by setting BCCR1:TCLKS[3:0] = 1110 to connect RCLK to TCLK. See Figure 7-7 and Figure 7-9.) 0 = Disabled 1 = Enabled Bit 2: Transmitter Power Down (TPD). Table 10-2 indicates the reduction in supply current when the transmitter is powered down. Note that the transmitter takes approximately 50ms to stabilize after TPD is set to 0. See Section 7.10.4.2. 0 = Normal transmitter operation 1 = Power down the transmitter and put TTIP and TRING pins in a high-impedance state (default) Bit 1: Receiver Power Down (RPD). Table 10-2 indicates the reduction in supply current when the receiver is powered down. Note that the receiver takes approximately 50ms to stabilize after RPD is set to 0. See Section 7.10.4.1. 0 = Normal receiver operation 1 = Power down the receiver (default) Bit 0: Transmit Enable (TE). See Section 7.10.4.2.3. 0 = Transmitter output driver disabled; TTIP and TRING pins in a high-impedance state 1 = Transmitter output driver enabled; TTIP and TRING active (THZE1 or THZE2 pin must be low)
19-4546; Rev 9; 5/09
157 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BLIR1 BITS LIU Information Register 1 18h Bit 6 RFAIL 0 Bit 5 OEQ 0 Bit 4 UEQ 0 Bit 3 -- 0 Bit 2 OC 0 Bit 1 SC 0 Bit 0 LOS 0
Name Default
Bit 6: Receiver Failure (RFAIL). This real-time status bit is set to 1 when the a short-circuit (less than 25) is detected on RTIP and/or RRING. 0 = Normal operation 1 = Short-circuit detected on RTIP and/or RRING Bit 5: Receive Over-Equalized (OEQ). This real-time status bit is set to 1 when the equalizer in the LIU receiver is over-equalized. This can happen if there is a very large unexpected resistive loss, such as when the device is placed in a monitor mode application without being configured for monitor mode (BLCR3:RMONEN). This indicator provides additional information when the receiver is indicating loss-of-signal in the LOS status bit. See Section 7.10.4.1. Bit 4: Receive Under-Equalized (UEQ). This real-time status bit is set to 1 when the equalizer in the LIU receiver is under-equalized. A signal with a very high resistive gain is being applied. This indicator provides additional information when the receiver is indicating loss-of-signal in the LOS status bit. See Section 7.10.4.1. Bit 2: Transmit Open Circuit (OC). This real-time status bit is set to 1 when the LIU detects that the TTIP and TRING outputs are open-circuited. Register BLSR1 has latched status bits that are set when OC changes state, both low-to-high and high-to-low. See Section 7.10.4.1.6. Bit 1: Transmit Short Circuit (SC). This real-time status bit is set to 1 when the LIU detects that the TTIP and TRING outputs are short-circuited. The short circuit resistance has to be 25 (typically) or less for short circuit detection. Register BLSR1 has latched status bits that are set when SC changes state, both low-to-high and highto-low. See Section 7.10.4.1.6. Bit 0: Receive Loss of Signal (LOS). This real-time status bit is set to 1 when the LIU receiver detects an LOS condition at RTIP and RRING. Register BLSR1 has latched status bits that are set when LOS changes state, both low-to-high and high-to-low. See Section 7.10.4.1.
19-4546; Rev 9; 5/09
158 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 0 BLIR2 BITS LIU Information Register 2 19h Bit 6 RL[3:0] 0 0 0 Bit 5 Bit 4 Bit 3 -- 0 Bit 2 -- 0 Bit 1 -- 0 Bit 0 -- 0
Bits 7 to 4: Receive Level (RL[3:0]). This real-time field indicates the pulse amplitude of the signal coming into the BITS LIU receiver. A value of 0 dB means 3.0V for DS1 and 2.37V for E1 and 2048 kHz. In 6312 kHz mode, a value of 0 means 0 dBm. See Section 7.10.4.1. RL[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 RECEIVE LEVEL (dB) > -2.5 -2.5 to -5.0 -5.0 to -7.5 -7.5 to -10.0 -10.0 to -12.5 -12.5 to -15.0 -15.0 to -17.5 -17.5 to -20.0 -20 to -22.5 -22.5 to -25.0 -25.0 to -27.5 -27.5 to -30.0 -30.0 to -32.5 -32.5 to -35.0 -35.0 to -37.5 <-37.5
19-4546; Rev 9; 5/09
159 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BLSR1 BITS LIU Status Register 1 1Ah Bit 6 OCC 0 Bit 5 SCC 0 Bit 4 LOSC 0 Bit 3 -- 0 Bit 2 OC 0 Bit 1 SC 0 Bit 0 LOS 0
Name Default
Bit 6: Transmit Open Circuit Clear (OCC). This latched status bit is set to 1 when BLIR1:OC changes state from high to low. OCC is cleared when written with a 1. When OCC is set it can cause an interrupt request on the INTREQ pin if the OCC interrupt enable bit is set in the BLIER1 register. See Section 7.10.4.1.6. Bit 5: Transmit Short Circuit Clear (SCC). This latched status bit is set to 1 when BLIR1:SC changes state from high to low. SCC is cleared when written with a 1. When SCC is set it can cause an interrupt request on the INTREQ pin if the SCC interrupt enable bit is set in the BLIER1 register. See Section 7.10.4.1.6. Bit 4: Receive Loss of Signal Clear (LOSC). This latched status bit is set to 1 when BLIR1:LOS changes state from high to low. LOSC is cleared when written with a 1. When LOSC is set it can cause an interrupt request on the INTREQ pin if the LOSC interrupt enable bit is set in the BLIER1 register. See Section 7.10.4.1. Bit 2: Transmit Open Circuit Detect (OC). This latched status bit is set to 1 when BLIR1:OC changes state from low to high. OC is cleared when written with a 1. When OC is set it can cause an interrupt request on the INTREQ pin if the OC interrupt enable bit is set in the BLIER1 register. See Section 7.10.4.2.7. Bit 1: Transmit Short Circuit Detect (SC). This latched status bit is set to 1 when BLIR1:SC changes state from low to high. SC is cleared when written with a 1. When SC is set it can cause an interrupt request on the INTREQ pin if the SC interrupt enable bit is set in the BLIER1 register. See Section 7.10.4.2.6. Bit 0: Receive Loss of Signal Detect (LOS). This latched status bit is set to 1 when BLIR1:LOS changes state from low to high. LOS is cleared when written with a 1. When LOS is set it can cause an interrupt request on the INTREQ pin if the LOS interrupt enable bit is set in the BLIER1 register. See Section 7.10.4.1.6.
19-4546; Rev 9; 5/09
160 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BLIER1 BITS LIU Interrupt Enable Register 1 1Bh Bit 6 OCC 0 Bit 5 SCC 0 Bit 4 LOSC 0 Bit 3 -- 0 Bit 2 OC 0 Bit 1 SC 0 Bit 0 LOS 0
Name Default
Bit 6: Interrupt Enable for Transmit Open Circuit Clear (OCC). This bit is an interrupt enable for the OCC bit in the BLSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 5: Interrupt Enable for Transmit Short Circuit Clear (SCC). This bit is an interrupt enable for the SCC bit in the BLSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 4: Interrupt Enable for Receive Loss of Signal Clear (LOSC). This bit is an interrupt enable for the LOSC bit in the BLSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 2: Interrupt Enable for Transmit Open Circuit Detect (OC). This bit is an interrupt enable for the OC bit in the BLSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 1: Interrupt Enable for Transmit Short Circuit Detect (SC). This bit is an interrupt enable for the SC bit in the BLSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 0: Interrupt Enable for Receive Loss of Signal (LOS). This bit is an interrupt enable for the LOS bit in the BLSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt
19-4546; Rev 9; 5/09
161 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 REN 0 BRMMR BITS Receive Master Mode Register 20h Bit 6 RID 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 RRST 0 Bit 0 RT1E1 0
Name Default
These register fields affect the receive framer only. See Sections 7.10.5.1 and 7.10.6.1. Bit 7: Receive Framer Enable (REN). This bit must be written with the desired value prior to setting the RID bit. 0 = Receive framer disabled (held in low-power state) 1 = Receive framer enabled (all features active) Bit 6: Receive Initialization Done (RID). System software must set the RT1E1 and REN bits prior to setting this bit. Once RID is set, the receiver is enabled if REN = 1. Bit 1: Receive Soft Reset (RRST). Level-sensitive reset. Should be set to 1, then to 0 to reset and initialize the receive framer. 0 = Normal operation 1 = Hold the receive framer in reset Bit 0: Receive T1/E1 Mode Select (RT1E1). This bit specifies the operating mode for the receive framer only. The BTMMR:TT1E1 bit specifies the operating mode for the transmit formatter. This bit must be set to the desired value before setting the RID bit. 0 = T1 (DS1) operation 1 = E1 operation
19-4546; Rev 9; 5/09
162 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 TEN 0 BTMMR BITS Transmit Master Mode Register 21h Bit 6 TID 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 TRST 0 Bit 0 TT1E1 0
Name Default
These register fields affect the transmit formatter only. See Sections 7.10.5.2 and 7.10.6.2. Bit 7: Transmit Formatter Enable (TEN). This bit must be written with the desired value prior to setting the TID bit. 0 = Transmit formatter disabled (held in low-power state) 1 = Transmit formatter enabled (all features active) Bit 6: Transmit Initialization Done (TID). System software must set the TT1E1 and TEN bits prior to setting this bit. Once TID is set, the transmitter is enabled if TEN = 1. Bit 1: Transmit Soft Reset (TRST). Level-sensitive reset. Should be set to 1, then to 0 to reset and initialize the transmit formatter. 0 = Normal operation 1 = Hold the transmit formatter in reset Bit 0: Transmit T1/E1 Mode Select (TT1E1). This bit specifies the operating mode for the transmit formatter only. The BRMMR:RT1E1 bit specifies the operating mode for the receive framer. This bit must be set to the desired value before setting the TID bit. 0 = T1 (DS1) operation 1 = E1 operation
19-4546; Rev 9; 5/09
163 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 SYNCT 0 BRCR1 BITS Receive Configuration Register 1 (DS1 only) 22h Bit 6 RB8ZS 0 Bit 5 RFM 0 Bit 4 ARC 0 Bit 3 SYNCC 0 Bit 2 RJC 0 Bit 1 SYNCD 0 Bit 0 RESYNC 0
Name Default
The fields of this register configure the receive framer when it is in DS1 mode only (BRMMR:RT1E1=0). In E1 mode this register is reserved and should not be written. See Section 7.10.5.1. Bit 7: Sync Time (SYNCT). This bit specifies the number of framing bits to quality. The type of framing bits to qualify is specified by the SYNCC configuration bit. 0 = Qualify 10 bits 1 = Qualify 24 bits Bit 6: Receive B8ZS Enable (RB8ZS). 0 = B8ZS decoding disabled 1 = B8ZS decoding enabled Bit 5: Receive Frame Mode Select (RFM). 0 = ESF framing mode 1 = SF (D4) framing mode Bit 4: Auto Resync Criteria (ARC). 0 = Resync on OOF or LOS event 1 = Resync on OOF only Bit 3: Sync Criteria (SYNCC). Superframe (SF) mode 0 = Search for Ft pattern then search for Fs pattern 1 = Cross-couple Ft and Fs pattern Extended Superframe (ESF) framing mode 0 = Search for FPS pattern only 1 = Search for FPS and verify with CRC6 Bit 2: Receive Japanese CRC-6 Enable (RJC). 0 = use ANSI/AT&T/ITU CRC-6 calculation (normal DS1 operation) 1 = use Japanese standard JT-G704 CRC-6 calculation (for J1 operation) Bit 1: Sync Disable (SYNCD). The bit specifies whether or not the receive framer automatically attempts to resynchronize to (i.e. search for the start-of-frame in) the incoming signal. 0 = Auto resync enabled 1 = Auto resync disabled Bit 0: Resynchronize (RESYNC). A zero-to-one transition causes the receive framer to resynchronize to (i.e. search for the start of frame in) the incoming signal. RESYNC must be cleared and set again for a subsequent resync.
19-4546; Rev 9; 5/09
164 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BRCR2 BITS Receive Configuration Register 2 (DS1 only) 23h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 Bit 2 OOFC[1:0] 0 0 Bit 1 RAIIE 0 Bit 0 RSFRAI 0
Name Default
The fields of this register configure the receive framer when it is in DS1 mode only (BRMMR:RT1E1=0). In E1 mode this register is reserved and should not be written. See Section 7.10.5.1. Bits 3 to 2: Out of Frame Criteria (OOFC[1:0]). This field specifies the criteria for declaring an out-of-frame (OOF) defect in BRIR1:OOF. 00 = 2/4 frame bits in error 01 = 2/5 frame bits in error 10 = 2/6 frame bits in error 11 = 2/6 frame bits in error Bit 1: Receive RAI Integration Enable (RAIIE). The ESF RAI indication can be interrupted for a period not to exceed 100 ms per interruption (T1.403). In ESF mode, setting RAIIE causes the RAI status to be integrated for 200ms. The RAI defect is indicated in BRIR1:RAI. 0 = RAI declared when 16 consecutive patterns of 00FFh appear in the FDL. RAI cleared when 14 or less patterns of 00FFh out of 16 possible appear in the FDL. 1 = RAI declared when the condition has been present for greater than 200ms. RAI cleared when the condition has been absent for greater than 200ms. Bit 0: Receive Superframe RAI Select (RSFRAI). When the receive framer is in superframe mode this bit specifies the type of RAI signal to detect. 0 = Zeros in bit 2 of all channels (normal DS1 operation) 1 = A one in the Fs bit position of frame 12 (J1 operation)
19-4546; Rev 9; 5/09
165 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BRCR3 BITS Receive Configuration Register 3 (E1 only) 24h Bit 6 RHDB3 0 Bit 5 RSIGM 0 Bit 4 -- 0 Bit 3 RCRC4 0 Bit 2 FRC 0 Bit 1 SYNCD 0 Bit 0 RESYNC 0
Name Default
The fields of this register configure the receive framer when it is in E1 mode only (BRMMR:RT1E1=1). In DS1 mode this register is reserved and should not be written. See Section 7.10.6.1. Bit 6: Receive HDB3 Enable (RHDB3). 0 = HDB3 decoding disabled 1 = HDB3 decoding enabled Bit 5 : Receive Signaling Mode Select (RSIGM). 0 = CAS signaling mode 1 = CCS signaling mode Bit 3: Receive CRC-4 Enable (RCRC4). 0 = CRC-4 framing disabled 1 = CRC-4 framing enabled Bit 2: Frame Resync Criteria (FRC). 0 = Resync if FAS is received in error three consecutive times 1 = Resync if either FAS or bit 2 of non-FAS is received in error three consecutive times Bit 1: Sync Disable (SYNCD). The bit specifies whether or not the receive framer automatically attempts to resynchronize to (i.e. search for the start-of-frame in) the incoming signal. 0 = Auto resync enabled 1 = Auto resync disabled Bit 0: Resynchronize (RESYNC). A zero-to-one transition causes the receive framer to resynchronize to (i.e. search for the start of frame in) the incoming signal. RESYNC must be cleared and set again for a subsequent resync.
Register Name: Register Description: Register Address: Bit 7 -- 0
BRCR4 BITS Receive Configuration Register 4 (E1 only) 25h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 -- 0 Bit 0 RLOSC 0
Name Default
The fields of this register configure the receive framer when it is in E1 mode only (BRMMR:RT1E1=1). In DS1 mode this register is reserved and should not be written. See Section 7.10.6.1. Bit 0: Receive Loss of Signal Criteria (RLOSC). 0 = RLOS declared upon 255 consecutive zeros (125 s) 1 = RLOS declared upon 2048 consecutive zeros (1 ms)
19-4546; Rev 9; 5/09
166 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BRCR5 BITS Receive Configuration Register 5 (DS1 and E1) 26h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 RMFS 0 Bit 0 1 1
Name Default
Bit 1: Receive Multiframe Sync Mode (RMFS). In E1 mode, this bit specifies the type of multiframe sync that comes out of the receive framer on the RMFSYNC node (Figure 7-7). In DS1 mode this bit must be set to 0. See Section 7.10.2. 0 = Pulse on CAS multiframe boundary 1 = Pulse on CRC-4 multiframe boundary Bit 0: Leave set to one (test control).
19-4546; Rev 9; 5/09
167 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 TJC 0 BTCR1 BITS Transmit Configuration Register 1 (DS1 only) 27h Bit 6 TFPT 0 Bit 5 TCPT 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 TB8ZS 0 Bit 1 TAIS 0 Bit 0 TRAI 0
Name Default
The fields of this register configure the transmit formatter when it is in DS1 mode only (BTMMR:TT1E1=0). In E1 mode this register is reserved and should not be written. See Section 7.10.5.2. Bit 7: Transmit Japanese CRC-6 Enable (TJC). 0 = Use ANSI/AT&T/ITU CRC-6 calculation (normal DS1 operation) 1 = Use Japanese standard JT-G704 CRC-6 calculation (J1 operation) Bit 6: Transmit F-Bit Pass-Through (TFPT). 0 = F bits sourced internally 1 = F bits sourced from TSER pin Bit 5: Transmit CRC Pass-Through (TCPT). 0 = CRC-6 bits sourced internally 1 = CRC-6 bits sourced from TSER pin during F-bit time Bit 2: Transmit B8ZS Enable (TB8ZS). 0 = B8ZS encoding disabled 1 = B8ZS encoding enabled Bit 1: Transmit Alarm Indication Signal (TAIS). 0 = Do not transmit AIS 1 = Transmit AIS (unframed all-ones) Bit 0: Transmit Remote Alarm Indication (TRAI). 0 = Do not transmit RAI 1 = Transmit RAI
19-4546; Rev 9; 5/09
168 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BTCR2 BITS Transmit Configuration Register 2 (DS1 only) 28h Bit 6 -- 0 Bit 5 -- 0 Bit 4 FBCT2 0 Bit 3 FBCT1 0 Bit 2 TSFRAI 0 Bit 1 TPDE 0 Bit 0 TB7ZS 0
Name Default
The fields of this register configure the transmit formatter when it is in DS1 mode only (BTMMR:TT1E1=0). In E1 mode this register is reserved and should not be written. See Section 7.10.5.2. Bit 4: F-Bit Corruption Type 2 (FBCT2). Setting this bit to 1 enables the corruption of one out of every 128 Ft bits (SF framing mode) or one out of every 128 FPS bits (ESF framing mode). F-bit corruption continues as long as FBCT2=1. Bit 3: F-Bit Corruption Type 1 (FBCT1). A zero-to-one transition causes the next three consecutive Ft bits (SF framing mode) or FPS bits (ESF framing mode) to be corrupted. This corruption is sufficient to cause the remote end to experience a loss of frame synchronization. Bit 2: Transmit Superframe RAI Select (TSFRAI). When the transmit formatter is in superframe mode this bit specifies the type of RAI signal to transmit. 0 = Zeros in bit 2 of all channels (normal DS1 operation) 1 = A one in the Fs bit position of frame 12 (J1 operation) Bit 1: Pulse Density Enforcer Enable (TPDE). The framer always examines both the transmit and receive data streams for violations of the ANSI T1.403 pulse density rules: no more than 15 consecutive zeros and at least N ones in each and every time window of 8 x (N +1) bits where N = 1 through 23. Violations for the transmit and receive data streams are reported in the BTSR1:TPDV and BRSR2:RPDV bits respectively. When this bit is set to one, the transmit formatter will force the transmitted stream to meet this requirement no matter the content of the transmitted stream. When B8ZS encoding is enabled (BTCR1:TB8ZS=1), this bit should be set to zero since B8ZSencoded data streams cannot violate the pulse density requirements. 0 = Disable transmit pulse density enforcer 1 = Enable transmit pulse density enforcer Bit 0: Transmit Bit 7 Zero-Suppression Enable (TB7ZS). 0 = No stuffing occurs 1 = Bit 7 forced to 1 in channels with all zeros
19-4546; Rev 9; 5/09
169 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BTCR3 BITS Transmit Configuration Register 3 (DS1 and E1) 29h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 TFM 0 Bit 1 IBPV 0 Bit 0 -- 0
Name Default
Bit 2: Transmit Frame Mode Select (TFM). In DS1 mode, this field specifies the DS1 framing mode. In E1 mode this field is unused and must be written with 0. See Section 7.10.5.2. 0 = ESF framing mode 1 = SF (D4) framing mode Bit 1: Insert BPV (IBPV). A zero-to-one transition on this bit will cause a single bipolar violation (BPV) to be inserted into the transmit data stream. After this bit has been toggled from a 0 to a 1, the device waits for the next occurrence of three consecutive ones to insert the BPV. This bit must be cleared and set again for a subsequent error to be inserted. See Sections 7.10.5.2 and 7.10.6.2.
19-4546; Rev 9; 5/09
170 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 TFPT 0 BTCR4 BITS Transmit Configuration Register 4 (E1 only) 2Ah Bit 6 -- 0 Bit 5 -- 0 Bit 4 TSiS 0 Bit 3 -- 0 Bit 2 THDB3 0 Bit 1 TAIS 0 Bit 0 TCRC4 0
Name Default
The fields of this register configure the transmit formatter when it is in E1 mode only (BTMMR:TT1E1=1). In DS1 mode this register is reserved and should not be written. See Section 7.10.6.2. Bit 7: Transmit Time Slot 0 Formatter Pass-Through (TFPT). See Figure 7-16 for the relative priority of this control bit vs. other control fields. 0 = FAS bits/Si bits/Sa bits/RAI sourced internally from the BTAF and BTNAF registers 1 = FAS bits/Si bits/Sa bits/RAI sourced from TSER pin Bit 4: Transmit International Bit Select (TSiS). See Figure 7-16 for the relative priority of this control bit vs. other transmit formatter control fields. 0 = Sample Si bits at TSER pin 1 = Source Si bits from the BTAF and BTNAF registers (in this mode, TFPT must be set to 0) Bit 2: Transmit HDB3 Enable (THDB3). 0 = HDB3 encoding disabled 1 = HDB3 encoding enabled Bit 1: Transmit Alarm Indication Signal (TAIS). 0 = Do not transmit AIS 1 = Transmit AIS (unframed all-ones) Bit 0: Transmit CRC-4 Enable (TCRC4). 0 = CRC-4 framing mode disabled 1 = CRC-4 framing mode enabled
19-4546; Rev 9; 5/09
171 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BRIIR BITS Receive Interrupt Information Register 30h Bit 6 BRSR4 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 BRSR3 0 Bit 0 BRSR1 0
Name Default
This register provide an indication of which BITS receive status registers have status bits set. When an interrupt request occurs, software can read BRIIR to quickly identify which of the BITS receive status registers might be causing the interrupt request. These bits clear once the appropriate interrupt request source has been serviced and cleared, as long as no other interrupt condition is present in the associated status register. Status bits that have been masked via the interrupt enable registers have no effect on these interrupt information bits. Bit 6: BITS Receive Status Register 4 (BRSR4). 0 = No status bits set 1 = Status bits set Bit 1: BITS Receive Status Register 3 (BRSR3). 0 = No status bits set 1 = Status bits set Bit 0: BITS Receive Status Register 1 (BRSR1). 0 = No status bits set 1 = Status bits set
19-4546; Rev 9; 5/09
172 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BRIR1 BITS Receive Information Register 1 (DS1 and E1) 31h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 RAI 0 Bit 2 AIS 0 Bit 1 LOS 0 Bit 0 OOF 0
Name Default
These fields provide real-time status information from the receive framer. See Table 7-16 (DS1) and Table 7-17 (E1) for set and clear criteria for RAI, AIS, LOS and OOF. The BRSR1 register has corresponding latched status registers. Bit 3: Remote Alarm Indication Condition (RAI). 0 = RAI not detected 1 = RAI detected Bit 2: Alarm Indication Signal Condition (AIS). 0 = AIS not detected 1 = AIS detected Bit 1: Loss of Signal Condition (LOS). 0 = LOS not detected 1 = LOS detected Bit 0: Out of Frame Condition (OOF). 0 = OOF not detected 1 = OOF detected
19-4546; Rev 9; 5/09
173 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Name Default 0 BRIR2 BITS Receive Information Register 2 (E1 only) 32h Bit 6 0 Bit 5 CSC[5:2,0] 0 Bit 4 0 Bit 3 0 Bit 2 CRC4SA 0 Bit 1 CASSA 0 Bit 0 FASSA 0
The fields of this register provide real-time status information from the receive framer when it is in E1 mode only (BRMMR:RT1E1=1). In DS1 mode these fields are undefined. See Section 7.10.6.1. Bits 7 to 3: CRC-4 Sync Counter bits (CSC[5:2] and CSC[0]). The CRC-4 sync counter increments each time the 8 ms CRC-4 multi-frame search times out. The counter is cleared when the framer has successfully obtained CRC-4 multiframe synchronization. The counter can also be cleared by disabling the CRC4 mode (BRCR3:RCRC4 = 0). This counter is useful for determining the amount of time the framer has been searching for synchronization at the CRC-4 level. ITU G.706 suggests that if synchronization at the CRC-4 level cannot be obtained within 400 ms, then the search should be abandoned and proper action taken. The CRC-4 sync counter rolls over when it reaches its maximum value. CSC[0] is the LSB of the 6-bit counter. (Note: The second LSB, CSC[1], is not accessible in this register to allow resolution to >400ms using 5 bits.) Bit 2: FAS Sync Active (FASSA). This real-time information bit is set while the synchronizer is searching for alignment at the FAS level. Bit 1: CAS MF Sync Active (CASSA). This real-time information bit is set while the synchronizer is searching for the CAS multi-frame alignment word. Bit 0: CRC-4 MF Sync Active (CRC4SA). This real-time information bit is set while the synchronizer is searching for the CRC-4 multi-frame alignment word.
19-4546; Rev 9; 5/09
174 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 RAIC 0 BRSR1 BITS Receive Status Register 1 (DS1 and E1) 33h Bit 6 AISC 0 Bit 5 LOSC 0 Bit 4 OOFC 0 Bit 3 RAI 0 Bit 2 AIS 0 Bit 1 LOS 0 Bit 0 OOF 0
Name Default
See Table 7-16 (DS1) and Table 7-17 (E1) for set and clear criteria for RAI, AIS, LOS and OOF. Bit 7: Remote Alarm Indication Clear (RAIC). This latched status bit is set to 1 when BRIR1:RAI changes state from high to low. RAIC is cleared when written with a 1. When RAIC is set it can cause an interrupt request on the INTREQ pin if the RAIC interrupt enable bit is set in the BRIER1 register. Bit 6: Alarm Indication Signal Clear (AISC). This latched status bit is set to 1 when BRIR1:AIS changes state from high to low. AISC is cleared when written with a 1. When AISC is set it can cause an interrupt request on the INTREQ pin if the AISC interrupt enable bit is set in the BRIER1 register. Bit 5: Loss of Signal Clear (LOSC). This latched status bit is set to 1 when BRIR1:LOS changes state from high to low. LOSC is cleared when written with a 1. When LOSC is set it can cause an interrupt request on the INTREQ pin if the LOSC interrupt enable bit is set in the BRIER1 register. Bit 4: Out of Frame Clear (OOFC). This latched status bit is set to 1 when BRIR1:OOF changes state from high to low. OOFC is cleared when written with a 1. When OOFC is set it can cause an interrupt request on the INTREQ pin if the OOFC interrupt enable bit is set in the BRIER1 register. Bit 3: Remote Alarm Indication (RAI). This latched status bit is set to 1 when BRIR1:RAI changes state from low to high. RAI is cleared when written with a 1. When RAI is set it can cause an interrupt request on the INTREQ pin if the RAI interrupt enable bit is set in the BRIER1 register. Bit 2: Alarm Indication Signal (AIS). This latched status bit is set to 1 when BRIR1:AIS changes state from low to high. AIS is cleared when written with a 1. When AIS is set it can cause an interrupt request on the INTREQ pin if the AIS interrupt enable bit is set in the BRIER1 register. Bit 1: Loss of Signal (LOS). This latched status bit is set to 1 when BRIR1:LOS changes state from low to high. LOS is cleared when written with a 1. When LOS is set it can cause an interrupt request on the INTREQ pin if the LOS interrupt enable bit is set in the BRIER1 register. See also the Receive Sensitivity paragraph in Section 7.10.4.1.6. Bit 0: Out of Frame (OOF). This latched status bit is set to 1 when BRIR1:OOF changes state from low to high. OOF is cleared when written with a 1. When OOF is set it can cause an interrupt request on the INTREQ pin if the OOF interrupt enable bit is set in the BRIER1 register.
19-4546; Rev 9; 5/09
175 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 RAIC 0 BRIER1 BITS Receive Interrupt Enable Register 1 (DS1 and E1) 34h Bit 6 AISC 0 Bit 5 LOSC 0 Bit 4 OOFC 0 Bit 3 RAI 0 Bit 2 AIS 0 Bit 1 LOS 0 Bit 0 OOF 0
Name Default
Bit 7: Interrupt Enable for Remote Alarm Indication Clear (RAIC). This bit is an interrupt enable for the RAIC bit in the BRSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 6: Interrupt Enable for Alarm Indication Signal Clear (AISC). This bit is an interrupt enable for the AISC bit in the BRSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 5: Interrupt Enable for Loss of Signal Clear (LOSC). This bit is an interrupt enable for the LOSC bit in the BRSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 4: Interrupt Enable for Out of Frame Clear (OOFC). This bit is an interrupt enable for the OOFC bit in the BRSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 3: Interrupt Enable for Remote Alarm Indication (RAI). This bit is an interrupt enable for the RAI bit in the BRSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 2: Interrupt Enable for Alarm Indication Signal (AIS). This bit is an interrupt enable for the AIS bit in the BRSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 1: Interrupt Enable for Loss of Signal (LOS). This bit is an interrupt enable for the LOS bit in the BRSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 0: Interrupt Enable for Out of Frame (OOF). This bit is an interrupt enable for the OOF bit in the BRSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt
19-4546; Rev 9; 5/09
176 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 RPDV 0 BRSR2 BITS Receive Status Register 2 (DS1 only) 35h Bit 6 -- 0 Bit 5 COFA 0 Bit 4 8ZD 0 Bit 3 16ZD 0 Bit 2 SEFE 0 Bit 1 B8ZS 0 Bit 0 FBE 0
Name Default
The fields of this register provide latched status information from the receive framer when it is in DS1 mode (BRMMR:RT1E1=0). In E1 mode these fields are undefined. None of these latched status bits can cause an interrupt request. See Section 7.10.5.1. Bit 7: Receive Pulse Density Violation Event (RPDV). This latched status bit is set to 1 when the incoming receive data stream does not meet the pulse density requirements of T1.403: no more than 15 consecutive zeros and at least N ones in each and every time window of 8 x (N +1) bits where N = 1 through 23. RPDV is cleared when written with a 1. Bit 5: Change-of-Frame Alignment Event (COFA). This latched status bit is set to 1 when the last resync resulted in a change of frame or multiframe alignment. COFA is cleared when written with a 1. Bit 4: Eight Zero Detect Event (8ZD). This latched status bit is set to 1 when a string of at least eight consecutive zeros (regardless of the length of the string) have been received in the incoming signal. 8ZD is cleared when written with a 1. Bit 3: Sixteen Zero Detect Event (16ZD). This latched status bit is set to 1 when a string of at least 16 consecutive zeros (regardless of the length of the string) have been received in the incoming signal. 16ZD is cleared when written with a 1. Bit 2: Severely Errored Framing Event (SEFE). This latched status bit is set to 1 when 2 out of 6 framing bits (Ft or FPS) are received in error. SEFE is cleared when written with a 1. Bit 1: B8ZS Codeword Detect Event (B8ZS). This latched status bit is set to 1 when a B8ZS codeword is detected in the incoming signal, regardless of whether the B8ZS mode is selected or not. This bit enables systems to automatically setting the line coding. B8ZS is cleared when written with a 1. Bit 0: Frame Bit Error Event (FBE). This latched status bit is set to 1 when an Ft (D4) or FPS (ESF) framing bit is received in error. FBE is cleared when written with a 1.
19-4546; Rev 9; 5/09
177 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BRSR3 BITS Receive Status Register 3 (E1 only) 36h Bit 6 CRCRC 0 Bit 5 CASRC 0 Bit 4 FASRC 0 Bit 3 RSA1 0 Bit 2 RSA0 0 Bit 1 RCMF 0 Bit 0 RAF 0
Name Default
The fields of this register provide latched status information from the receive framer when it is in E1 mode only (BRMMR:RT1E1=1). In DS1 mode these fields are undefined. See Section 7.10.6.1. Bit 6: CRC-4 Resync Criteria Met (CRCRC). This latched status bit is set to 1 when 915 out of 1000 CRC-4 multiframe alignment words are received in error. CRCRC is cleared when written with a 1 and not set again until the CRC resync criteria is met again. CRCRC cannot cause an interrupt request. Bit 5: CAS Resync Criteria Met (CASRC). This latched status bit is set to 1 when two consecutive CAS multiframe alignment words are received in error. CASRC is cleared when written with a 1 and not set again until the CAS resync criteria is met again. CASRC cannot cause an interrupt request. Bit 4: FAS Resync Criteria Met (FASRC). This latched status bit is set to 1 when three consecutive FAS words are received in error. FASRC is cleared when written with a 1 and not set again until the FAS resync criteria is met again. FASRC cannot cause an interrupt request. Bit 3: Receive Signaling All Ones Event (RSA1). This latched status bit is set to 1 when timeslot 16 contains fewer than three zeros for 16 consecutive frames. RSA1 is cleared when written with a 1. When RSA1 is set it can cause an interrupt request on the INTREQ pin if the RSA1 interrupt enable bit is set in the BRIER3 register. In all other modes RSA1 remains set to 0. Bit 2: Receive Signaling All Zeros Event (RSA0). This latched status bit is set to 1 when timeslot 16 contains all zeros over a full multi-frame. RSA0 is cleared when written with a 1. When RSA0 is set it can cause an interrupt request on the INTREQ pin if the RSA0 interrupt enable bit is set in the BRIER3 register. In all other modes RSA0 remains set to 0. Bit 1: Receive CRC-4 Multi-Frame (RCMF). This latched status bit is set to 1 every 2 ms on CRC-4 multiframe boundaries. RCMF is cleared when written with a 1. When RCMF is set it can cause an interrupt request on the INTREQ pin if the RCMF interrupt enable bit is set in the BRIER3 register. In all other modes RCMF remains set to 0. See Section 7.10.6.4. Bit 0: Receive Align Frame (RAF). This latched status bit is set to 1 every 250 s at the beginning of align frames. RAF is cleared when written with a 1. When RAF is set it can cause an interrupt request on the INTREQ pin if the RAF interrupt enable bit is set in the BRIER3 register. In all other modes RAF remains set to 0. See Section 7.10.6.3.
19-4546; Rev 9; 5/09
178 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BRIER3 BITS Receive Interrupt Enable Register 3 (E1 only) 37h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 RSA1 0 Bit 2 RSA0 0 Bit 1 RCMF 0 Bit 0 RAF 0
Name Default
The fields of this register configure interrupt masking for the corresponding bits in the BRSR3 register when the receive framer is in E1 mode only (BRMMR:RT1E1=1). In DS1 mode this register is reserved and should not be written. See Section 7.10.6.1. Bit 3: Interrupt Enable for Receive Signaling All Ones Event (RSA1). This bit is an interrupt enable for the RSA1 bit in the BRSR3 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 2: Interrupt Enable for Receive Signaling All Zeros Event (RSA0). This bit is an interrupt enable for the RSA0 bit in the BRSR3 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 1: Interrupt Enable for Receive CRC-4 Multi-Frame (RCMF). This bit is an interrupt enable for the RCMF bit in the BRSR3 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 0: Interrupt Enable for Receive Align Frame (RAF). This bit is an interrupt enable for the RAF bit in the BRSR3 register. 0 = Mask the interrupt 1 = Enable the interrupt
19-4546; Rev 9; 5/09
179 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BRSR4 BITS Receive Status Register 4 (DS1 only) 38h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 BC 0 Bit 0 BD 0
Name Default
The fields of this register provide latched status information from the receive framer when it is in DS1 mode (BRMMR:RT1E1=0). In E1 mode these fields are undefined. See Section 7.10.5.3. Bit 1: Receive BOC Clear (BC). This latched status bit is set to 1 when a valid BOC is no longer detected, with the disintegration filter applied as specified in BRBCR:RBD[1:0]. BC is cleared when written with a 1. When BC is set it can cause an interrupt request on the INTREQ pin if the BC interrupt enable bit is set in the BRIER4 register. Bit 0: Receive BOC Detected (BD). This latched status bit is set to 1 when a valid BOC has been detected, with the validation filter applied as specified in BRBCR:RBF. BD is cleared when written with a 1. When BD is set it can cause an interrupt request on the INTREQ pin if the BD interrupt enable bit is set in the BRIER4 register.
Register Name: Register Description: Register Address: Bit 7 -- 0
BRIER4 BITS Interrupt Enable Register 4 (DS1 only) 39h Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 BC 0 Bit 0 BD 0
Name Default
Bit 1: Interrupt Enable for Receive BOC Clear (BC). This bit is an interrupt enable for the BC bit in the BRSR4 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 0: Interrupt Enable for Receive BOC Detected (BD). This bit is an interrupt enable for the BD bit in the BRSR4 register. 0 = Mask the interrupt 1 = Enable the interrupt
19-4546; Rev 9; 5/09
180 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BTSR1 BITS Transmit Status Register 1 (DS1 and E1) 3Ah Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 TPDV/TAF 0 Bit 2 TMF 0 Bit 1 LOTCC 0 Bit 0 LOTC 0
Name Default
Bit 3: Transmit Pulse Density Violation (TPDV) / Transmit Align Frame (TAF). In DS1 mode this latched status bit functions as TPDV and is set to 1 when the transmit data stream does not meet the ANSI T1.403 requirements for pulse density: no more than 15 consecutive zeros and at least N ones in each and every time window of 8 x (N +1) bits where N = 1 through 23. In E1 mode this bit functions as TAF and is set to 1 every 250 s at the beginning of align frames. TPDV/TAF is cleared when written with a 1. When TPDV/TAF is set it can cause an interrupt to occur on the INTREQ pin if the TPDV/TAF interrupt enable bit is set in the BTIER1 register. See Section 7.10.6.3. Bit 2: Transmit Multi-Frame (TMF). In DS1 mode this latched status bit is set to 1 every 1.5 ms on superframe boundaries (SF mode) or every 3 ms on extended superframe boundaries (ESF mode). In E1 mode this bit is set every 2 ms on multiframe boundaries. TMF is cleared when written with a 1. When TMF is set it can cause an interrupt to occur on the INTREQ pin if the TMF interrupt enable bit is set in the BTIER1 register. See Section 7.10.6.4. Bit 1: Loss of Transmit Clock Clear (LOTCC). This latched status bit is set to 1 when the transmit clock source has transitioned for approximately 15 MCLK periods. LOTCC is cleared when written with a 1. When LOTCC is set it can cause an interrupt request on the INTREQ pin if the LOTCC interrupt enable bit is set in the BTIER1 register. Bit 0: Loss of Transmit Clock (LOTC). This latched status bit is set to 1 when the transmit clock source has not transitioned for approximately 15 MCLK periods. LOTC is cleared when written with a 1. When LOTC is set it can cause an interrupt request on the INTREQ pin if the LOTC interrupt enable bit is set in the BTIER1 register.
Register Name: Register Description: Register Address: Bit 7 -- 0
BTIER1 BITS Transmit Interrupt Enable Register 1 (DS1 and E1) 3Bh Bit 6 -- 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 TPDV/TAF 0 Bit 2 TMF 0 Bit 1 LOTCC 0 Bit 0 LOTC 0
Name Default
Bit 3: Interrupt Enable for Transmit Pulse Density Violation (TPDV) / Transmit Align Frame (TAF). This bit is an interrupt enable for the TPDV/TMF bit in the BTSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 2: Interrupt Enable for Transmit Multi-Frame (TMF). This bit is an interrupt enable for the TMF bit in the BTSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 1: Interrupt Enable for Loss of Transmit Clock Clear (LOTCC). This bit is an interrupt enable for the LOTCC bit in the BTSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 0: Interrupt Enable for Loss of Transmit Clock (LOTC). This bit is an interrupt enable for the LOTC bit in the BTSR1 register. 0 = Mask the interrupt 1 = Enable the interrupt 19-4546; Rev 9; 5/09 181 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 RBR 0 BRBCR BITS Receive BOC Control Register (DS1 only) 40h Bit 6 -- 0 Bit 5 Bit 4 RBD[1:0] 0 0 Bit 3 0 Bit 2 RBF[2:0] 0 Bit 1 0 Bit 0 -- 0
Name Default
When the BITS receive framer is in DS1 ESF mode this register configures the receive BOC controller. In E1 mode this register is reserved and should not be written. See Section 7.10.5.3. Bit 7: Receive BOC Reset (RBR). A zero-to-one transition resets the BOC circuitry. RBR must be cleared and set again for a subsequent reset. Modifications to the RBF and RBD fields are not applied to the BOC controller until a BOC reset has been completed. Bits 5 to 4: Receive BOC Disintegration Bits (RBD[1:0]). The receive BOC logic must examine the number of message bits specified by RBD[1:0] before declaring that a valid BOC is no longer detected. The BC bit in BRSR4 is set to indicate that a valid BOC is no longer present.
RBD[1:0] 00 01 10 11 Consecutive Message Bits for BOC Clear 16 32 48 64
Bits 3 to 1: Receive BOC Filter Bits (RBF[2:0]). The receive BOC logic uses the criteria specified by this field to validate incoming BOC codes. The BD bit in BRSR4 is set to indicate the detection of a validated BOC code.
RBF[2:0] 000 001 010 011 100 Validation Criteria for BOC Detected 1 3 in a row 5 in a row 7 in a row 7 out of 10
Register Name: Register Description: Register Address: Bit 7 -- 0
BTBCR BITS Transmit BOC Control Register (DS1 only) 41h Bit 6 SBOC 0 Bit 5 -- 0 Bit 4 -- 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 -- 0 Bit 0 -- 0
Name Default
When the BITS transmitter is in DS1 mode ESF mode this register configures the transmit BOC controller. In all other modes this register is reserved and should not be written. See Section 7.10.5.3. Bit 6: Send BOC (SBOC). 0 = Do not transmit BOC codes 1 = Repeatedly transmit the BOC code stored in the BTBOC register
19-4546; Rev 9; 5/09
182 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BRBOC BITS Receive BOC Register (DS1 only) 42h Bit 6 -- 0 Bit 5 0 Bit 4 0 Bit 3 Bit 2 RBOC[5:0] 0 0 Bit 1 0 Bit 0 0
Name Default
Bits 5 to 0: Receive BOC (RBOC[5:0]). DS1 ESF mode only. After a BOC has been validated per the criteria specified by BRBCR:RBF, the BOC is stored in this field where it can be read by software. The device notifies software that a valid BOC is available by setting the BD bit in BRSR4. Setting BD can optionally drive an interrupt request on the INTREQ pin. Bit 0 is the first bit received. See Section 7.10.5.3.
Register Name: Register Description: Register Address: Bit 7 -- 0
BTBOC BITS Transmit BOC Register (DS1 only) 43h Bit 6 -- 0 Bit 5 0 Bit 4 0 Bit 3 Bit 2 TBOC[5:0] 0 0 Bit 1 0 Bit 0 0
Name Default
Bits 5 to 0: Transmit BOC (TBOC[5:0]). DS1 ESF mode only. This field specifies the six data bits of the 16-bit BOC message to be transmitted in the ESF data link. When SBOC=1 in BTBCR the BOC is repeatedly transmitted on the data link. When SBOC=0, the data link idle code (01111110b = 7Eh) is transmitted continuously on the data link. Bit 0 is the first bit transmitted. See Section 7.10.5.3.
19-4546; Rev 9; 5/09
183 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Si 0 BRAF BITS Receive Align Frame Register (E1 only) 50h Bit 6 0 Bit 5 0 Bit 4 0 Bit 3 FAS[6:0] 0 Bit 2 0 Bit 1 0 Bit 0 0
Name Default
The align frame is the E1 frame containing the frame alignment signal (FAS). The bits of this register indicate the first eight bits received in the most recent align frame. The bits are latched into this register at the start of the align frame. The start of the align frame is indicated by the RAF status bit in BRSR3. See Section 7.10.6.3. Bit 7: International Bit (Si). Bits 6 to 0: Frame Alignment Signal (FAS[6:0]. When a normal E1 signal is being received, FAS[6:0]=0011011.
Register Name: Register Description: Register Address: Bit 7 Si 0
BRNAF BITS Receive Non-Align Frame Register (E1 only) 51h Bit 6 1 0 Bit 5 RAI 0 Bit 4 Sa4 0 Bit 3 Sa5 0 Bit 2 Sa6 0 Bit 1 Sa7 0 Bit 0 Sa8 0
Name Default
The non-align frame is the E1 frame that does not contain the frame alignment signal (FAS). The bits of this register indicate the first eight bits received in the most recent non-align frame. The bits are latched into this register at the start of the align frame. The start of the align frame is indicated by the RAF status bit in BRSR3. See Section 7.10.6.3. Bit 7: International Bit (Si). Bit 6: Non-Align Frame Signal Bit. Set to 1 in a normal E1 double frame. Bit 5: Remote Alarm Indication (RAI). This is the normal status bit for detecting RAI in the incoming E1 signal. 0 = No alarm condition 1 = Alarm condition Bits 4 to 0: Additional Spare Bits (Sa4 to Sa8).
19-4546; Rev 9; 5/09
184 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 SiF14 0 BRSiAF BITS Receive Si Bits of the Align Frame (E1 only) 52h Bit 6 SiF12 0 Bit 5 SiF10 0 Bit 4 SiF8 0 Bit 3 SiF6 0 Bit 2 SiF4 0 Bit 1 SiF2 0 Bit 0 SiF0 0
Name Default
The align frame is the E1 frame containing the frame alignment signal (FAS). The bits of this register indicate the Si bits received in the align frames of the most recent CRC-4 multiframe. The Si bits received in each multiframe are saved in internal registers and latched into this register at the start of the next CRC-4 multiframe. The CRC-4 multiframe boundary is indicated by the RCMF status bit in BRSR3. See Section 7.10.6.4. Bit 7: Si Bit from Frame 14 (SiF14). Bit 6: Si Bit from Frame 12 (SiF12). Bit 5: Si Bit from Frame 10 (SiF10). Bit 4: Si Bit from Frame 8 (SiF8). Bit 3: Si Bit from Frame 6 (SiF6). Bit 2: Si Bit from Frame 4 (SiF4). Bit 1: Si Bit from Frame 2 (SiF2). Bit 0: Si Bit from Frame 0 (SiF0).
Register Name: Register Description: Register Address: Bit 7 SiF15 0
BRSiNAF BITS Receive Si Bits of the Non-Align Frame (E1 only) 53h Bit 6 SiF13 0 Bit 5 SiF11 0 Bit 4 SiF9 0 Bit 3 SiF7 0 Bit 2 SiF5 0 Bit 1 SiF3 0 Bit 0 SiF1 0
Name Default
The non-align frame is the E1 frame that does not contain the frame alignment signal (FAS). The bits of this register indicate the Si bits received in the non-align frames of the most recent CRC-4 multiframe. The Si bits received in each multiframe are saved in internal registers and latched into this register at the start of the next CRC-4 multiframe. The CRC-4 multiframe boundary is indicated by the RCMF status bit in BRSR3. See Section 7.10.6.4. Bit 7: Si Bit from Frame 15 (SiF15). Bit 6: Si Bit from Frame 13 (SiF13). Bit 5: Si Bit from Frame 11 (SiF11). Bit 4: Si Bit from Frame 9 (SiF9). Bit 3: Si Bit from Frame 7 (SiF7). Bit 2: Si Bit from Frame 5 (SiF5). Bit 1: Si Bit from Frame 3 (SiF3). Bit 0: Si Bit from Frame 1 (SiF1).
19-4546; Rev 9; 5/09
185 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 RAIF15 0 BRRAI BITS Receive Remote Alarm Indication Bits (E1 only) 54h Bit 6 RAIF13 0 Bit 5 RAIF11 0 Bit 4 RAIF9 0 Bit 3 RAIF7 0 Bit 2 RAIF5 0 Bit 1 RAIF3 0 Bit 0 RAIF1 0
Name Default
The RAI bits received in each multiframe are saved in internal registers and latched into this register at the start of the next CRC-4 multiframe. The CRC-4 multiframe boundary is indicated by the RCMF status bit in BRSR3. See Section 7.10.6.4. Bit 7: RAI Bit from Frame 15 (RAIF15). Bit 6: RAI Bit from Frame 13 (RAIF13). Bit 5: RAI Bit from Frame 11 (RAIF11). Bit 4: RAI Bit from Frame 9 (RAIF9). Bit 3: RAI Bit from Frame 7 (RAIF7). Bit 2: RAI Bit from Frame 5 (RAIF5). Bit 1: RAI Bit from Frame 3 (RAIF3). Bit 0: RAI Bit from Frame 1 (RAIF1).
Register Name: Register Description: Register Address: Bit 7 Sa4F15 0
BRSa4 BITS Receive Sa4 Bits (E1 only) 55h Bit 6 Sa4F13 0 Bit 5 Sa4F11 0 Bit 4 Sa4F9 0 Bit 3 Sa4F7 0 Bit 2 Sa4F5 0 Bit 1 Sa4F3 0 Bit 0 Sa4F1 0
Name Default
The Sa4 bits received in each multiframe are saved in internal registers and latched into this register at the start of the next CRC-4 multiframe. The CRC-4 multiframe boundary is indicated by the RCMF status bit in BRSR3. See Section 7.10.6.4. Bit 7: Sa4 Bit from Frame 15 (Sa4F15). Bit 6: Sa4 Bit from Frame 13 (Sa4F13). Bit 5: Sa4 Bit from Frame 11 (Sa4F11). Bit 4: Sa4 Bit from Frame 9 (Sa4F9). Bit 3: Sa4 Bit from Frame 7 (Sa4F7). Bit 2: Sa4 Bit from Frame 5 (Sa4F5). Bit 1: Sa4 Bit from Frame 3 (Sa4F3). Bit 0: Sa4 Bit from Frame 1 (Sa4F1).
19-4546; Rev 9; 5/09
186 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Sa5F15 0 BRSa5 BITS Receive Sa5 Bits (E1 only) 56h Bit 6 Sa5F13 0 Bit 5 Sa5F11 0 Bit 4 Sa5F9 0 Bit 3 Sa5F7 0 Bit 2 Sa5F5 0 Bit 1 Sa5F3 0 Bit 0 Sa5F1 0
Name Default
The Sa5 bits received in each multiframe are saved in internal registers and latched into this register at the start of the next CRC-4 multiframe. The CRC-4 multiframe boundary is indicated by the RCMF status bit in BRSR3. See Section 7.10.6.4. Bit 7: Sa5 Bit from Frame 15 (Sa5F15). Bit 6: Sa5 Bit from Frame 13 (Sa5F13). Bit 5: Sa5 Bit from Frame 11 (Sa5F11). Bit 4: Sa5 Bit from Frame 9 (Sa5F9). Bit 3: Sa5 Bit from Frame 7 (Sa5F7). Bit 2: Sa5 Bit from Frame 5 (Sa5F5). Bit 1: Sa5 Bit from Frame 3 (Sa5F3). Bit 0: Sa5 Bit from Frame 1 (Sa5F1).
Register Name: Register Description: Register Address: Bit 7 Sa6F15 0
BRSa6 BITS Receive Sa6 Bits (E1 only) 57h Bit 6 Sa6F13 0 Bit 5 Sa6F11 0 Bit 4 Sa6F9 0 Bit 3 Sa6F7 0 Bit 2 Sa6F5 0 Bit 1 Sa6F3 0 Bit 0 Sa6F1 0
Name Default
The Sa6 bits received in each multiframe are saved in internal registers and latched into this register at the start of the next CRC-4 multiframe. The CRC-4 multiframe boundary is indicated by the RCMF status bit in BRSR3. See Section 7.10.6.4. Bit 7: Sa6 Bit from Frame 15 (Sa6F15). Bit 6: Sa6 Bit from Frame 13 (Sa6F13). Bit 5: Sa6 Bit from Frame 11 (Sa6F11). Bit 4: Sa6 Bit from Frame 9 (Sa6F9). Bit 3: Sa6 Bit from Frame 7 (Sa6F7). Bit 2: Sa6 Bit from Frame 5 (Sa6F5). Bit 1: Sa6 Bit from Frame 3 (Sa6F3). Bit 0: Sa6 Bit from Frame 1 (Sa6F1).
19-4546; Rev 9; 5/09
187 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Sa7F15 0 BRSa7 BITS Receive Sa7 Bits (E1 only) 58h Bit 6 Sa7F13 0 Bit 5 Sa7F11 0 Bit 4 Sa7F9 0 Bit 3 Sa7F7 0 Bit 2 Sa7F5 0 Bit 1 Sa7F3 0 Bit 0 Sa7F1 0
Name Default
The Sa7 bits received in each multiframe are saved in internal registers and latched into this register at the start of the next CRC-4 multiframe. The CRC-4 multiframe boundary is indicated by the RCMF status bit in BRSR3. See Section 7.10.6.4. Bit 7: Sa7 Bit from Frame 15 (Sa7F15). Bit 6: Sa7 Bit from Frame 13 (Sa7F13). Bit 5: Sa7 Bit from Frame 11 (Sa7F11). Bit 4: Sa7 Bit from Frame 9 (Sa7F9). Bit 3: Sa7 Bit from Frame 7 (Sa7F7). Bit 2: Sa7 Bit from Frame 5 (Sa7F5). Bit 1: Sa7 Bit from Frame 3 (Sa7F3). Bit 0: Sa7 Bit from Frame 1 (Sa7F1).
Register Name: Register Description: Register Address: Bit 7 Sa8F15 0
BRSa8 BITS Receive Sa8 Bits (E1 only) 59h Bit 6 Sa8F13 0 Bit 5 Sa8F11 0 Bit 4 Sa8F9 0 Bit 3 Sa8F7 0 Bit 2 Sa8F5 0 Bit 1 Sa8F3 0 Bit 0 Sa8F1 0
Name Default
The Sa8 bits received in each multiframe are saved in internal registers and latched into this register at the start of the next CRC-4 multiframe. The CRC-4 multiframe boundary is indicated by the RCMF status bit in BRSR3. See Section 7.10.6.4. Bit 7: Sa8 Bit from Frame 15 (Sa8F15). Bit 6: Sa8 Bit from Frame 13 (Sa8F13). Bit 5: Sa8 Bit from Frame 11 (Sa8F11). Bit 4: Sa8 Bit from Frame 9 (Sa8F9). Bit 3: Sa8 Bit from Frame 7 (Sa8F7). Bit 2: Sa8 Bit from Frame 5 (Sa8F5). Bit 1: Sa8 Bit from Frame 3 (Sa8F3). Bit 0: Sa8 Bit from Frame 1 (Sa8F1).
19-4546; Rev 9; 5/09
188 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BRMCR BITS Receive Message Control Register (E1 only) 5Ah Bit 6 0 Bit 5 SSMCH[2:0] 0 Bit 4 0 Bit 3 -- 0 Bit 2 -- 0 Bit 1 Bit 0 SSMF[1:0] 0 0
Name Default
Bits 6 to 4: Receive SSM Channel (SSMCH[2:0]). This field specifies the Sa-bit channel to look at when reading the most recently validated SSM message from BRSSM:SSM[3:0]. After this field is changed, the SSM for the newly selected Sa bit channel does not appear in BRSSM:SSM[3:0] for approximately 250s. See Section 7.10.6.5. 000 = Sa4 001 = Sa5 010 = Sa6 011 = Sa7 100 = Sa8 Bits 1 to 0: Receive SSM Filter (SSMF[1:0]). The logic that detects new SSM messages in the E1 Sa bits uses the criteria specified by this field to validate incoming SSM codes. The Sa4 through Sa8 fields in the BRMSR register are set to indicate the detection of a validated SSM code. See Section 7.10.6.5. 00 = Validate new SSM when present for 1 multiframe 01 = Validate new SSM when present for 2 multiframes in a row 10 = Validate new SSM when present for 3 multiframes in a row 11 = Validate new SSM when present in 3 out of 4 consecutive multiframes
19-4546; Rev 9; 5/09
189 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BRMSR BITS Receive Message Status Register (E1 only) 5Bh Bit 6 0 Bit 5 Sa8 0 Bit 4 -- 0 Bit 3 Sa7 0 Bit 2 Sa6 0 Bit 1 Sa5 0 Bit 0 Sa4 0
Name Default
Bit 5: New Validated SSM in the Sa8 Bits (Sa8). This latched status bit is set to 1 when a new SSM message has been validated in the Sa8 channel according the criteria specified by BRMCR:SSMF. When Sa8 is set it can cause an interrupt request on the INTREQ pin if the Sa8 interrupt enable bit is set in the BRMCR register. Sa8 is cleared when written with a 1 and not set again until another SSM change is validated in the Sa8 channel. See Section 7.10.6.5. Bit 3: New Validated SSM in the Sa7 Bits (Sa7). This latched status bit is set to 1 when a new SSM message has been validated in the Sa7 channel according the criteria specified by BRMCR:SSMF. When Sa7 is set it can cause an interrupt request on the INTREQ pin if the Sa7 interrupt enable bit is set in the BRMCR register. Sa7 is cleared when written with a 1 and not set again until another SSM change is validated in the Sa7 channel. See Section 7.10.6.5. Bit 2: New Validated SSM in the Sa6 Bits (Sa6). This latched status bit is set to 1 when a new SSM message has been validated in the Sa6 channel according the criteria specified by BRMCR:SSMF. When Sa6 is set it can cause an interrupt request on the INTREQ pin if the Sa6 interrupt enable bit is set in the BRMCR register. Sa6 is cleared when written with a 1 and not set again until another SSM change is validated in the Sa6 channel. See Section 7.10.6.5. Bit 1: New Validated SSM in the Sa5 Bits (Sa5). This latched status bit is set to 1 when a new SSM message has been validated in the Sa5 channel according the criteria specified by BRMCR:SSMF. When Sa5 is set it can cause an interrupt request on the INTREQ pin if the Sa5 interrupt enable bit is set in the BRMCR register. Sa5 is cleared when written with a 1 and not set again until another SSM change is validated in the Sa5 channel. See Section 7.10.6.5. Bit 0: New Validated SSM in the Sa4 Bits (Sa4). This latched status bit is set to 1 when a new SSM message has been validated in the Sa4 channel according the criteria specified by BRMCR:SSMF. When Sa4 is set it can cause an interrupt request on the INTREQ pin if the Sa4 interrupt enable bit is set in the BRMCR register. Sa4 is cleared when written with a 1 and not set again until another SSM change is validated in the Sa4 channel. See Section 7.10.6.5.
19-4546; Rev 9; 5/09
190 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 -- 0 BRMIER BITS Receive Message Interrupt Enable Register (E1 only) 5Ch Bit 6 -- 0 Bit 5 Sa8 0 Bit 4 -- 0 Bit 3 Sa7 0 Bit 2 Sa6 0 Bit 1 Sa5 0 Bit 0 Sa4 0
Name Default
Bit 5: Interrupt Enable for Sa8 (Sa8). This bit is an interrupt enable for the Sa8 status bit in the BRMSR register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 3: Interrupt Enable for Sa7 (Sa7). This bit is an interrupt enable for the Sa7 status bit in the BRMSR register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 2: Interrupt Enable for Sa6 (Sa6). This bit is an interrupt enable for the Sa6 status bit in the BRMSR register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 1: Interrupt Enable for Sa5 (Sa5). This bit is an interrupt enable for the Sa5 status bit in the BRMSR register. 0 = Mask the interrupt 1 = Enable the interrupt Bit 0: Interrupt Enable for Sa4 (Sa4). This bit is an interrupt enable for the Sa4 status bit in the BRMSR register. 0 = Mask the interrupt 1 = Enable the interrupt
Register Name: Register Description: Register Address: Bit 7 -- 0
BRSSM BITS Receive SSM Register (E1 only) 5Dh Bit 6 0 Bit 5 SSMCH[2:0] 0 Bit 4 0 Bit 3 0 Bit 2 Bit 1 SSM[3:0] 0 0 Bit 0 0
Name Default
Bits 6 to 4: Receive SSM Channel (SSMCH[2:0]). This field specifies the Sa-bit channel for which the SSM bits are being displayed in the SSM[3:0] field. The value in this field matches the value in BRMCR:SSMCH[2:0] after a delay of approximately 250s. See Section 7.10.6.5. 000 = Sa4 001 = Sa5 010 = Sa6 011 = Sa7 100 = Sa8 Bits 3 to 0: Receive SSM (SSM[3:0]). This read-only field contains the most recently validated SSM message from the Sa-bit channel indicated in BRSSM:SSMCH[2:0]. The Sa bit channel to display in this field is specified by BRMCR:SSMCH[2:0]. See Section 7.10.6.5.
19-4546; Rev 9; 5/09
191 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Si 0 BTAF BITS Transmit Align Frame Register (E1 only) 60h Bit 6 0 Bit 5 0 Bit 4 1 Bit 3 FAS[6:0] 1 Bit 2 0 Bit 1 1 Bit 0 1
Name Default
The align frame is the E1 frame containing the frame alignment signal (FAS). The bits of this register specify the first eight bits of the align frame. The bits are sampled from this register at the start of the align frame, which is indicated by the TAF status bit in BTSR1. Various control fields can cause some of these bits to be sourced from elsewhere. See Section 7.10.6.3. Bit 7: International Bit (Si). Bits 6 to 0: Frame Alignment Signal (FAS[6:0]. Should be set to 0011011 for normal E1 operation.
Register Name: Register Description: Register Address: Bit 7 Si 0
BTNAF BITS Transmit Non-Align Frame Register (E1 only) 61h Bit 6 1 1 Bit 5 RAI 0 Bit 4 Sa4 0 Bit 3 Sa5 0 Bit 2 Sa6 0 Bit 1 Sa7 0 Bit 0 Sa8 0
Name Default
The non-align frame is the E1 frame that does not contain the frame alignment signal (FAS). The bits of this register specify the first eight bits of the non-align frame.. The bits are sampled from this register at the start of the align frame, which is indicated by the TAF status bit in BTSR1. Various control fields can cause some of these bits to be sourced from elsewhere. See Section 7.10.6.3. Bit 7: International Bit (Si). Bit 6: Non-Align Frame Signal Bit. Should be set to 1 for normal E1 operation. Bit 5: Remote Alarm Indication (RAI). This is the normal control bit for manipulating the RAI bit in the outgoing E1 frames. 0 = No alarm condition 1 = Alarm condition Bits 4 to 0: Additional Spare Bits (Sa4 to Sa8).
19-4546; Rev 9; 5/09
192 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 SiF14 0 BTSiAF BITS Transmit Si Bits of the Align Frame (E1 only) 62h Bit 6 SiF12 0 Bit 5 SiF10 0 Bit 4 SiF8 0 Bit 3 SiF6 0 Bit 2 SiF4 0 Bit 1 SiF2 0 Bit 0 SiF0 0
Name Default
The align frame is the E1 frame containing the frame alignment signal (FAS). When SiAF=1 in BTOCR, the bits of this register specify the Si bits to be transmitted in the align frames of outgoing multiframes. The Si bits are sampled from this register at the start of the multiframe. The multiframe boundary is indicated by the TMF status bit in BTSR1. See Section 7.10.6.4. Bit 7: Si Bit of Frame 14 (SiF14). Bit 6: Si Bit of Frame 12 (SiF12). Bit 5: Si Bit of Frame 10 (SiF10). Bit 4: Si Bit of Frame 8 (SiF8). Bit 3: Si Bit of Frame 6 (SiF6). Bit 2: Si Bit of Frame 4 (SiF4). Bit 1: Si Bit of Frame 2 (SiF2). Bit 0: Si Bit of Frame 0 (SiF0).
Register Name: Register Description: Register Address: Bit 7 SiF15 0
BTSiNAF BITS Transmit Si Bits of the Non-Align Frame (E1 only) 63h Bit 6 SiF13 0 Bit 5 SiF11 0 Bit 4 SiF9 0 Bit 3 SiF7 0 Bit 2 SiF5 0 Bit 1 SiF3 0 Bit 0 SiF1 0
Name Default
The non-align frame is the E1 frame that does not contain the frame alignment signal (FAS). When SiNAF=1 in BTOCR, the bits of this register specify the Si bits to be transmitted in the non-align frames of outgoing multiframes. The Si bits are sampled from this register at the start of the multiframe. The multiframe boundary is indicated by the TMF status bit in BTSR1. See Section 7.10.6.4. Bit 7: Si Bit of Frame 15 (SiF15). Bit 6: Si Bit of Frame 13 (SiF13). Bit 5: Si Bit of Frame 11 (SiF11). Bit 4: Si Bit of Frame 9 (SiF9). Bit 3: Si Bit of Frame 7 (SiF7). Bit 2: Si Bit of Frame 5 (SiF5). Bit 1: Si Bit of Frame 3 (SiF3). Bit 0: Si Bit of Frame 1 (SiF1).
19-4546; Rev 9; 5/09
193 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 RAIF15 0 BTRAI BITS Transmit Remote Alarm Indication Bits (E1 only) 64h Bit 6 RAIF13 0 Bit 5 RAIF11 0 Bit 4 RAIF9 0 Bit 3 RAIF7 0 Bit 2 RAIF5 0 Bit 1 RAIF3 0 Bit 0 RAIF1 0
Name Default
When RAI=1 in BTOCR, the bits of this register specify the RAI bits to be transmitted in outgoing multiframes. The RAI bits are sampled from this register at the start of the multiframe. The multiframe boundary is indicated by the TMF status bit in BTSR1. See Section 7.10.6.4. Bit 7: RAI Bit of Frame 15 (RAIF15). Bit 6: RAI Bit of Frame 13 (RAIF13). Bit 5: RAI Bit of Frame 11 (RAIF11). Bit 4: RAI Bit of Frame 9 (RAIF9). Bit 3: RAI Bit of Frame 7 (RAIF7). Bit 2: RAI Bit of Frame 5 (RAIF5). Bit 1: RAI Bit of Frame 3 (RAIF3). Bit 0: RAI Bit of Frame 1 (RAIF1).
Register Name: Register Description: Register Address: Bit 7 Sa4F15 0
BTSa4 BITS Transmit Sa4 Bits (E1 only) 65h Bit 6 Sa4F13 0 Bit 5 Sa4F11 0 Bit 4 Sa4F9 0 Bit 3 Sa4F7 0 Bit 2 Sa4F5 0 Bit 1 Sa4F3 0 Bit 0 Sa4F1 0
Name Default
When Sa4=1 in BTOCR, the bits of this register specify the Sa4 bits to be transmitted in outgoing multiframes. The Sa4 bits are sampled from this register at the start of the multiframe. The multiframe boundary is indicated by the TMF status bit in BTSR1. See Section 7.10.6.4. Bit 7: Sa4 Bit of Frame 15 (Sa4F15). Bit 6: Sa4 Bit of Frame 13 (Sa4F13). Bit 5: Sa4 Bit of Frame 11 (Sa4F11). Bit 4: Sa4 Bit of Frame 9 (Sa4F9). Bit 3: Sa4 Bit of Frame 7 (Sa4F7). Bit 2: Sa4 Bit of Frame 5 (Sa4F5). Bit 1: Sa4 Bit of Frame 3 (Sa4F3). Bit 0: Sa4 Bit of Frame 1 (Sa4F1).
19-4546; Rev 9; 5/09
194 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Sa5F15 0 BTSa5 BITS Transmit Sa5 Bits (E1 only) 66h Bit 6 Sa5F13 0 Bit 5 Sa5F11 0 Bit 4 Sa5F9 0 Bit 3 Sa5F7 0 Bit 2 Sa5F5 0 Bit 1 Sa5F3 0 Bit 0 Sa5F1 0
Name Default
When Sa5=1 in BTOCR, the bits of this register specify the Sa5 bits to be transmitted in outgoing multiframes. The Sa5 bits are sampled from this register at the start of the multiframe. The multiframe boundary is indicated by the TMF status bit in BTSR1. See Section 7.10.6.4. Bit 7: Sa5 Bit of Frame 15 (Sa5F15). Bit 6: Sa5 Bit of Frame 13 (Sa5F13). Bit 5: Sa5 Bit of Frame 11 (Sa5F11). Bit 4: Sa5 Bit of Frame 9 (Sa5F9). Bit 3: Sa5 Bit of Frame 7 (Sa5F7). Bit 2: Sa5 Bit of Frame 5 (Sa5F5). Bit 1: Sa5 Bit of Frame 3 (Sa5F3). Bit 0: Sa5 Bit of Frame 1 (Sa5F1).
Register Name: Register Description: Register Address: Bit 7 Sa6F15 0
BTSa6 BITS Transmit Sa6 Bits (E1 only) 67h Bit 6 Sa6F13 0 Bit 5 Sa6F11 0 Bit 4 Sa6F9 0 Bit 3 Sa6F7 0 Bit 2 Sa6F5 0 Bit 1 Sa6F3 0 Bit 0 Sa6F1 0
Name Default
When Sa6=1 in BTOCR, the bits of this register specify the Sa6 bits to be transmitted in outgoing multiframes. The Sa6 bits are sampled from this register at the start of the multiframe. The multiframe boundary is indicated by the TMF status bit in BTSR1. See Section 7.10.6.4. Bit 7: Sa6 Bit of Frame 15 (Sa6F15). Bit 6: Sa6 Bit of Frame 13 (Sa6F13). Bit 5: Sa6 Bit of Frame 11 (Sa6F11). Bit 4: Sa6 Bit of Frame 9 (Sa6F9). Bit 3: Sa6 Bit of Frame 7 (Sa6F7). Bit 2: Sa6 Bit of Frame 5 (Sa6F5). Bit 1: Sa6 Bit of Frame 3 (Sa6F3). Bit 0: Sa6 Bit of Frame 1 (Sa6F1).
19-4546; Rev 9; 5/09
195 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 Sa7F15 0 BTSa7 BITS Transmit Sa7 Bits (E1 only) 68h Bit 6 Sa7F13 0 Bit 5 Sa7F11 0 Bit 4 Sa7F9 0 Bit 3 Sa7F7 0 Bit 2 Sa7F5 0 Bit 1 Sa7F3 0 Bit 0 Sa7F1 0
Name Default
When Sa7=1 in BTOCR, the bits of this register specify the Sa7 bits to be transmitted in outgoing multiframes. The Sa7 bits are sampled from this register at the start of the multiframe. The multiframe boundary is indicated by the TMF status bit in BTSR1. See Section 7.10.6.4. Bit 7: Sa7 Bit of Frame 15 (Sa7F15). Bit 6: Sa7 Bit of Frame 13 (Sa7F13). Bit 5: Sa7 Bit of Frame 11 (Sa7F11). Bit 4: Sa7 Bit of Frame 9 (Sa7F9). Bit 3: Sa7 Bit of Frame 7 (Sa7F7). Bit 2: Sa7 Bit of Frame 5 (Sa7F5). Bit 1: Sa7 Bit of Frame 3 (Sa7F3). Bit 0: Sa7 Bit of Frame 1 (Sa7F1).
Register Name: Register Description: Register Address: Bit 7 Sa8F15 0
BTSa8 BITS Transmit Sa8 Bits (E1 only) 69h Bit 6 Sa8F13 0 Bit 5 Sa8F11 0 Bit 4 Sa8F9 0 Bit 3 Sa8F7 0 Bit 2 Sa8F5 0 Bit 1 Sa8F3 0 Bit 0 Sa8F1 0
Name Default
When Sa8=1 in BTOCR, the bits of this register specify the Sa8 bits to be transmitted in outgoing multiframes. The Sa8 bits are sampled from this register at the start of the multiframe. The multiframe boundary is indicated by the TMF status bit in BTSR1. See Section 7.10.6.4. Bit 7: Sa8 Bit of Frame 15 (Sa8F15). Bit 6: Sa8 Bit of Frame 13 (Sa8F13). Bit 5: Sa8 Bit of Frame 11 (Sa8F11). Bit 4: Sa8 Bit of Frame 9 (Sa8F9). Bit 3: Sa8 Bit of Frame 7 (Sa8F7). Bit 2: Sa8 Bit of Frame 5 (Sa8F5). Bit 1: Sa8 Bit of Frame 3 (Sa8F3). Bit 0: Sa8 Bit of Frame 1 (Sa8F1).
19-4546; Rev 9; 5/09
196 of 227
DS3100 Register Name: Register Description: Register Address: Bit 7 SiAF 0 BTOCR BITS Transmit Overhead Control Register (E1 only) 6Ah Bit 6 SiNAF 0 Bit 5 RAI 0 Bit 4 Sa4 0 Bit 3 Sa5 0 Bit 2 Sa6 0 Bit 1 Sa7 0 Bit 0 Sa8 0
Name Default
When set to 1 these control bits have precedence over any other source of Si/RAI/Sa bits, including the CRC-4 Si bit generation logic. See Section 7.10.6. Bit 7: Si In Align Frame Data Source (SiAF). 0 = Do not source the Si bits in the align frame from the BTSiAF register 1 = Source the Si bits in the align frame from the BTSiAF register Bit 6: Si In Non-Align Frame Data Source (SiNAF). 0 = Do not source the Si bits in the non-align frame from the BTSiNAF register 1 = Source the Si bits in the non-align frame from the BTSiNAF register Bit 5: RAI Data Source (RAI). 0 = Do not source the RAI bits from the BTRAI register 1 = Source the RAI bits from the BTRAI register Bit 4: Sa4 Data Source (Sa4). 0 = Do not source the Sa4 bits from the BTSa4 register 1 = Source the Sa4 bits from the BTSa4 register Bit 3: Sa5 Data Source (Sa5). 0 = Do not source the Sa5 bits from the BTSa5 register 1 = Source the Sa5 bits from the BTSa5 register Bit 2: Sa6 Data Source (Sa6). 0 = Do not source the Sa6 bits from the BTSa6 register 1 = Source the Sa6 bits from the BTSa6 register Bit 1: Sa7 Data Source (Sa7). 0 = Do not source the Sa7 bits from the BTSa7 register 1 = Source the Sa7 bits from the BTSa7 register Bit 0: Sa8 Data Source (Sa8). 0 = Do not source the Sa8 bits from the BTSa8 register 1 = Source the Sa8 bits from the BTSa8 register
19-4546; Rev 9; 5/09
197 of 227
DS3100
9. JTAG TEST ACCESS PORT AND BOUNDARY SCAN
9.1 JTAG Description
The DS3100 supports the standard instruction codes SAMPLE/PRELOAD, BYPASS, and EXTEST. Optional public instructions included are HIGHZ, CLAMP, and IDCODE. Figure 9-1 shows a block diagram. The DS3100 contains the following items, which meet the requirements set by the IEEE 1149.1 Standard Test Access Port and Boundary Scan Architecture: Test Access Port (TAP) TAP Controller Instruction Register Bypass Register Boundary Scan Register Device Identification Register
The TAP has the necessary interface pins, namely JTCLK, JTRST, JTDI, JTDO, and JTMS. Details on these pins can be found in Table 6-8. Details about the boundary scan architecture and the TAP can be found in IEEE 1149.11990, IEEE 1149.1a-1993, and IEEE 1149.1b-1994.
Figure 9-1. JTAG Block Diagram
BOUNDARY SCAN REGISTER DEVICE IDENTIFICATION REGISTER BYPASS REGISTER
INSTRUCTION REGISTER
SELECT
TEST ACCESS PORT CONTROLLER
TRI-STATE
50k JTDI
50k JTMS JTCLK
50k JTRST JTDO
19-4546; Rev 9; 5/09
MUX
198 of 227
DS3100
9.2
JTAG TAP Controller State Machine Description
This section discusses the operation of the TAP controller state machine. The TAP controller is a finite state machine that responds to the logic level at JTMS on the rising edge of JTCLK. Each of the states denoted in Figure 9-2 are described in the following paragraphs. Test-Logic-Reset. Upon device power-up, the TAP controller starts in the Test-Logic-Reset state. The instruction register contains the IDCODE instruction. All system logic on the device operates normally. Run-Test-Idle. Run-Test-Idle is used between scan operations or during specific tests. The instruction register and all test registers remain idle. Select-DR-Scan. All test registers retain their previous state. With JTMS low, a rising edge of JTCLK moves the controller into the Capture-DR state and initiates a scan sequence. JTMS high moves the controller to the SelectIR-SCAN state. Capture-DR. Data can be parallel-loaded into the test register selected by the current instruction. If the instruction does not call for a parallel load or the selected test register does not allow parallel loads, the register remains at its current value. On the rising edge of JTCLK, the controller goes to the Shift-DR state if JTMS is low or to the Exit1DR state if JTMS is high. Shift-DR. The test register selected by the current instruction is connected between JTDI and JTDO and data is shifted one stage toward the serial output on each rising edge of JTCLK. If a test register selected by the current instruction is not placed in the serial path, it maintains its previous state. Exit1-DR. While in this state, a rising edge on JTCLK with JTMS high puts the controller in the Update-DR state, which terminates the scanning process. A rising edge on JTCLK with JTMS low puts the controller in the Pause-DR state. Pause-DR. Shifting of the test registers is halted while in this state. All test registers selected by the current instruction retain their previous state. The controller remains in this state while JTMS is low. A rising edge on JTCLK with JTMS high puts the controller in the Exit2-DR state. Exit2-DR. While in this state, a rising edge on JTCLK with JTMS high puts the controller in the Update-DR state and terminates the scanning process. A rising edge on JTCLK with JTMS low puts the controller in the Shift-DR state. Update-DR. A falling edge on JTCLK while in the Update-DR state latches the data from the shift register path of the test registers into the data output latches. This prevents changes at the parallel output because of changes in the shift register. A rising edge on JTCLK with JTMS low puts the controller in the Run-Test-Idle state. With JTMS high, the controller enters the Select-DR-Scan state. Select-IR-Scan. All test registers retain their previous state. The instruction register remains unchanged during this state. With JTMS low, a rising edge on JTCLK moves the controller into the Capture-IR state and initiates a scan sequence for the instruction register. JTMS high during a rising edge on JTCLK puts the controller back into the Test-Logic-Reset state. Capture-IR. The Capture-IR state is used to load the shift register in the instruction register with a fixed value. This value is loaded on the rising edge of JTCLK. If JTMS is high on the rising edge of JTCLK, the controller enters the Exit1-IR state. If JTMS is low on the rising edge of JTCLK, the controller enters the Shift-IR state. Shift-IR. In this state, the instruction register's shift register is connected between JTDI and JTDO and shifts data one stage for every rising edge of JTCLK toward the serial output. The parallel register and the test registers remain at their previous states. A rising edge on JTCLK with JTMS high moves the controller to the Exit1-IR state. A rising edge on JTCLK with JTMS low keeps the controller in the Shift-IR state, while moving data one stage through the instruction shift register. Exit1-IR. A rising edge on JTCLK with JTMS low puts the controller in the Pause-IR state. If JTMS is high on the rising edge of JTCLK, the controller enters the Update-IR state and terminates the scanning process. 19-4546; Rev 9; 5/09 199 of 227
DS3100 Pause-IR. Shifting of the instruction register is halted temporarily. With JTMS high, a rising edge on JTCLK puts the controller in the Exit2-IR state. The controller remains in the Pause-IR state if JTMS is low during a rising edge on JTCLK. Exit2-IR. A rising edge on JTCLK with JTMS high puts the controller in the Update-IR state. The controller loops back to the Shift-IR state if JTMS is low during a rising edge of JTCLK in this state. Update-IR. The instruction shifted into the instruction shift register is latched into the parallel output on the falling edge of JTCLK as the controller enters this state. Once latched, this instruction becomes the current instruction. A rising edge on JTCLK with JTMS low puts the controller in the Run-Test-Idle state. With JTMS high, the controller enters the Select-DR-Scan state.
Figure 9-2. JTAG TAP Controller State Machine
Test-Logic-Reset 1 0 1 Select DR-Scan 0 1 Capture-DR 0 Shift-DR 1 Exit1- DR 0 Pause-DR 1 0 Exit2-DR 1 Update-DR 1 0 1 0 1 1 1 Select IR-Scan 0 Capture-IR 0 Shift-IR 1 Exit1-IR 0 Pause-IR 1 Exit2-IR 1 Update-IR 0 1 1
0
Run-Test/Idle
0
0
0
0
19-4546; Rev 9; 5/09
200 of 227
DS3100
9.3
JTAG Instruction Register and Instructions
The instruction register contains a shift register as well as a latched parallel output and is 3 bits in length. When the TAP controller enters the Shift-IR state, the instruction shift register is connected between JTDI and JTDO. While in the Shift-IR state, a rising edge on JTCLK with JTMS low shifts data one stage toward the serial output at JTDO. A rising edge on JTCLK in the Exit1-IR state or the Exit2-IR state with JTMS high moves the controller to the UpdateIR state. The falling edge of that same JTCLK latches the data in the instruction shift register to the instruction parallel output. Table 9-1 shows the instructions supported by the DS3100 and their respective operational binary codes.
Table 9-1. JTAG Instruction Codes
INSTRUCTIONS SAMPLE/PRELOAD BYPASS EXTEST CLAMP HIGHZ IDCODE SELECTED REGISTER Boundary Scan Bypass Boundary Scan Bypass Bypass Device Identification INSTRUCTION CODES 010 111 000 011 100 001
SAMPLE/PRELOAD. SAMPLE/RELOAD is a mandatory instruction for the IEEE 1149.1 specification. This instruction supports two functions. First, the digital I/Os of the device can be sampled at the boundary scan register, using the Capture-DR state, without interfering with the device's normal operation. Second, data can be shifted into the boundary scan register through JTDI using the Shift-DR state. EXTEST. EXTEST allows testing of the interconnections to the device. When the EXTEST instruction is latched in the instruction register, the following actions occur: (1) Once the EXTEST instruction is enabled through the Update-IR state, the parallel outputs of the digital output pins are driven. (2) The boundary scan register is connected between JTDI and JTDO. (3) The Capture-DR state samples all digital inputs into the boundary scan register. BYPASS. When the BYPASS instruction is latched into the parallel instruction register, JTDI is connected to JTDO through the 1-bit bypass register. This allows data to pass from JTDI to JTDO without affecting the device's normal operation. IDCODE. When the IDCODE instruction is latched into the parallel instruction register, the device identification register is selected. The device ID code is loaded into the device identification register on the rising edge of JTCLK, following entry into the Capture-DR state. Shift-DR can be used to shift the ID code out serially through JTDO. During Test-Logic-Reset, the ID code is forced into the instruction register's parallel output. HIGHZ. All digital outputs are placed into a high-impedance state. The bypass register is connected between JTDI and JTDO. CLAMP. All digital output pins output data from the boundary scan parallel output while connecting the bypass register between JTDI and JTDO. The outputs do not change during the CLAMP instruction.
19-4546; Rev 9; 5/09
201 of 227
DS3100
9.4
JTAG Test Registers
IEEE 1149.1 requires a minimum of two test registers--the bypass register and the boundary scan register. An optional test register, the identification register, has been included in the device design. It is used with the IDCODE instruction and the Test-Logic-Reset state of the TAP controller. Bypass Register. This is a single 1-bit shift register used with the BYPASS, CLAMP, and HIGHZ instructions to provide a short path between JTDI and JTDO. Boundary Scan Register. This register contains a shift register path and a latched parallel output for control cells and digital I/O cells. BSDL files are available at www.maxim-ic.com/TechSupport/telecom/bsdl.htm. Identification Register. This register contains a 32-bit shift register and a 32-bit latched parallel output. It is selected during the IDCODE instruction and when the TAP controller is in the Test-Logic-Reset state. The device identification code for the DS3100 is shown in Table 9-2.
Table 9-2. JTAG ID Code
DEVICE DS3100 REVISION Consult factory DEVICE CODE 0000000000011100 MANUFACTURER CODE 00010100001 REQUIRED 1
19-4546; Rev 9; 5/09
202 of 227
DS3100
10.
ELECTRICAL CHARACTERISTICS
ABSOLUTE MAXIMUM RATINGS
Voltage Range on Any Pin with Respect to VSS (except VDD)......................................................-0.3V to +5.5V Supply Voltage Range (VDD) with Respect to VSS...................................................................-0.3V to +1.98V Supply Voltage Range (VDDIO) with Respect to VSS.................................................................-0.3V to +3.63V Ambient Operating Temperature Range...................................................................-40C to +85C (Note 1) Junction Operating Temperature Range.............................................................................-40C to +125C Storage Temperature Range............................................................................................-55C to +125C Soldering Temperature..................................................................See IPC/JEDEC J-STD-020 Specification
Note 1: Specifications to -40C are guaranteed by design and not production tested. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to the absolute maximum rating conditions for extended periods may affect device. Ambient operating temperature range when device is mounted on a four-layer JEDEC test board with no airflow.
10.1
DC Characteristics
Table 10-1. Recommended DC Operating Conditions
(TA = -40C to +85C)
PARAMETER Supply Voltage, Core Supply Voltage, I/O Ambient Temperature Range SYMBOL VDD VDDIO TA CONDITIONS MIN 1.62 3.135 -40 TYP 1.8 3.3 MAX 1.98 3.465 +85 UNITS V V C
Table 10-2. DC Characteristics
(VDD = 1.8V 10%, VDDIO = 3.3V 5%, TA = -40C to +85C.)
PARAMETER 1.8V Supply Current 1.8V 3.3V 3.3V Supply Current Reduction When One BITS Transmitter is Powered Down Supply Current Reduction When One BITS Receiver is Powered Down Supply Current from VDD_OC6 When output OC6 is Enabled Supply Current from VDD_OC7 When output OC7 is Enabled Input Capacitance Output Capacitance
Note 2: Note 3:
SYMBOL IDD18 IDD18 IDD33 IDD33 IDDR1 IDDR2 IDDOC6 IDDOC7 CIN COUT
CONDITIONS (Note 2) (Note 3) (Note 2) (Note 3) BLCR4:TPD = 1 BLCR4:RPD = 1 (Note 4) (Note 4)
MIN
TYP 129 130 36 124 35 9 8 8 5 7
MAX 152 154 53 145
UNITS
mA
mA mA mA mA pF pF
12.800MHz clock applied to REFCLK. Both BITS transceivers shut down, 19.44MHz clock applied to one CMOS/TTL input clock pin. One 19.44MHz CMOS/TTL output clock pin driving 100pF load; all other inputs at VDDIO or grounded; all other outputs open. 12.800MHz clock applied to REFCLK. Both BITS transceivers enabled in E1 mode, transmitting and receiving over 75 cables through recommended transformers and external circuitry. 19.44MHz clock applied to one CMOS/TTL input clock pin. One 19.44MHz CMOS/TTL output clock pin driving 100pF load; all other inputs at VDDIO or grounded; all other outputs open. 19.44MHz output clock frequency, driving the load shown in Figure 10-1.
Note 4:
19-4546; Rev 9; 5/09
203 of 227
DS3100
Table 10-3. CMOS/TTL Pins
(VDD = 1.8V 10%, VDDIO = 3.3V 5%, TA = -40C to +85C.)
PARAMETER Input High Voltage Input Low Voltage Input Leakage Input Leakage, Pins with Internal Pullup Resistor (50k typical) Input Leakage, Pins with Internal Pulldown Resistor (50k typical) Output Leakage (when High Impedance) Output High Voltage (IO = -4.0mA) Output Low Voltage (IO = +4.0mA)
Note 1:
SYMBOL VIH VIL IIL IILPU IILPD ILO VOH VOL
CONDITIONS
MIN 2.0 -0.3 -10 -85 -10 -10 2.4 0
TYP
MAX 5.5 +0.8 +10 +10 +85 +10 VDDIO 0.4
UNITS V V A A A A V V
(Note 1) (Note 1) (Note 1) (Note 1)
0V < VIN < VDDIO for all other digital inputs.
Table 10-4. LVDS Pins
(VDD = 1.8V 10%, VDDIO = 3.3V 5%, TA = -40C to +85C.) (See Figure 10-1.)
PARAMETER Input Voltage Range Differential Input Voltage Differential Input Logic Threshold Output High Voltage Output Low Voltage Differential Output Voltage Output Offset Voltage (Common Mode Voltage) Difference in Magnitude of Output Differential Voltage for Complementary States
Note 1: Note 2:
SYMBOL VINLVDS VIDLVDS VTHLVDS VOHLVDS VOLLVDS VODLVDS VOSLVDS VDOSLVDS
CONDITIONS VIDLVDS = 100mV
MIN 0 0.1 -100 0.885 250 1.08
TYP
MAX 2.4 1.4 +100 1.65 450
UNITS V V mV V V mV V mV
(Note 1) (Note 1) +25C (Note 1)
1.45 1.1 1.28
1.45 25
With 100 load across the differential outputs. The DS3100's LVDS output pins can easily be interfaced to LVPECL and CML inputs on neighboring ICs using a few external passive components. See Maxim App Note HFAN-1.0 for details.
Figure 10-1. Recommended Termination for LVDS Pins
50 input signal POS 50 input signal NEG 100 input POS input NEG output POS
(5%)
50 50 output NEG 100
(5%)
output signal POS output signal NEG
19-4546; Rev 9; 5/09
204 of 227
DS3100
Table 10-5. LVPECL Pins
(VDD = 1.8V 10%, VDDIO = 3.3V 5%, TA = -40C to +85C) (See Figure 10-2.)
PARAMETER Input High Voltage, Differential Inputs Input Low Voltage, Differential Inputs Input Differential Voltage Input High Voltage, Single-Ended Inputs Input Low Voltage, Single-Ended Inputs
Note 1: Note 2: Note 3:
SYMBOL VIHPECL VILPECL VIDPECL VIHPECL,S VILPECL,S
CONDITIONS (Note 1) (Note 1)
MIN VDDIO 2.4 VDDIO 2.5 0.1 VDDIO 1.3 VDDIO 2.4
TYP
MAX VDDIO 0.4 VDDIO 0.5 1.4 VDDIO 0.5 VDDIO 1.5
UNITS V V V V V
(Note 2) (Note 2)
For a differential input voltage 100mV. With the unused differential input tied to VDDIO - 1.4V. Although the DS3100's differential outputs do not directly drive standard LVPECL signals, these output pins can easily be interfaced to LVPECL and CML inputs on neighboring ICs using a few external passive components. See Maxim App Note HFAN-1.0 for details.
Figure 10-2. Recommended Termination for LVPECL Pins
VDD_ICDIFF 130 50 input signal POS 50 input signal NEG input NEG input POS 130
82
82
VSS_ICDIFF
19-4546; Rev 9; 5/09
205 of 227
DS3100
Table 10-6. AMI Composite Clock Pins
(VDD = 1.8V 10%, VDDIO = 3.3V 5%, TA = -40C to +85C.) (Note 1) (See Figure 10-3.)
PARAMETER Input High Voltage Input Middle Voltage Input Low Voltage Input LOS Threshold Input Pulse Width Input Rise/Fall Time
Note 1:
SYMBOL VIHAMI VIMAMI VILAMI VLOS tPW tR, tF
CONDITIONS
MIN 2.2 1.5 -0.3
TYP
1.65 0.2
MAX VDDIO + 0.3 1.8 1.1
UNITS V V V V s s
At the IC1/IC2 pin 1.6
7.8
14 0.5
The timing parameters in this table are guaranteed by design (GBD).
Figure 10-3. Recommended External Components for AMI Composite Clock Pins
470 nF
RS
input signal
470 nF
IC1 IC2
OC8POS
0.01uF RP
1:1
output signal POS
input signal
OC8NEG
RS
output signal NEG
For input CC signals compliant with Telcordia GR-378 (amplitude 2.7V to 5.5V) or ITU G.703 Section 4.2.2 option b) (3V0.5V), the signal should be attenuated by a factor of 3 (or more) before being presented to IC1A or IC2A. Input CC signals with a 1V nominal pulse amplitude can be presented unattenuated. For output CC signals, Table 10-7 specifies recommended values for the components in Figure 10-3. Recommended transformers include the PE-65540 from Pulse Engineering.
Table 10-7. Recommended External Components for Output Clock OC8
SIGNAL TYPE GR-378 (133, 2.7V-5.5V) G.703 4.2.2 option b) (110, 3V 0.5V) G.703 4.2.2 option a) and Appendix II.1 (110, 1V 0.1V) G.703 4.2.3 (120, 1V 0.1V) RS 0 0 91 91 RP open open 360 300
19-4546; Rev 9; 5/09
206 of 227
DS3100
10.2
Input Clock Timing
Table 10-8. Input Clock Timing
(VDD = 1.8V 10%, VDDIO = 3.3V 5%, TA = -40C to +85C.)
PARAMETER Input Clock Period, CMOS/TTL Input Pins Input Clock Period, LVDS/LVPECL Input Pins Input Clock High, Low Time SYMBOL tCYC tCYC tH, tL MIN 8ns (125MHz) 6.43ns (155.52MHz) 3ns or 30% of tCYC, whichever is smaller TYP MAX 500s (2kHz) 500s (2kHz)
10.3
Output Clock Timing
Table 10-9. Input Clock to Output Clock Delay
INPUT FREQUENCY 8kHz 6.48MHz 19.44MHz 25.92MHz 38.88MHz 51.84MHz 77.76MHz 155.52MHz OUTPUT FREQUENCY 8kHz 6.48MHz 19.44MHz 25.92MHz 38.88MHz 51.84MHz 77.76MHz 155.52MHz DELAY, INPUT CLOCK EDGE TO OUTPUT CLOCK EDGE 0.0 1.5ns -12 1.5ns 0.0 1.5ns 0.0 1.5ns 0.0 1.5ns 0.0 1.5ns 0.0 1.5ns 0.0 1.5ns
Table 10-10. Output Clock Phase Alignment, Frame Sync Alignment Mode
OUTPUT FREQUENCY 8kHz (OC10) 2kHz 8kHz 1.544MHz (OC9) 2.048MHz (OC9) 44.736MHz 34.368MHz 6.48MHz 19.44MHz 25.92MHz 38.88MHz 51.84MHz 77.76MHz 155.52MHz 311.04MHz DELAY, OC1 (2kHz) FALLING EDGE TO OUTPUT CLOCK FALLING EDGE 0.0 0.5ns 0.0 0.5ns 0.0 0.5ns 0.0 1.25ns 0.0 1.25ns -2.0 1.25ns -2.0 1.25ns -2.0 1.25ns -2.0 1.25ns -2.0 1.25ns -2.0 1.25ns -2.0 1.25ns -2.0 1.25ns -2.0 1.25ns -2.0 1.25ns
See Section 7.9.3 for details on frame sync alignment and the SYNC2K pin. 19-4546; Rev 9; 5/09 207 of 227
DS3100
10.4
BITS Transceiver Timing
Table 10-11. BITS Receiver Timing
(VDD = 1.8V 10%, VDDIO = 3.3V 5%, TA = -40C to +85C.) (Note 1) (See Figure 10-4.)
PARAMETER RCLK Period RCLK Duty Cycle RCLK to RSER Delay RCLK to ROUT Delay RCLK, RSER and ROUT Rise and Fall Times ROUT Pulse Width
Note 1: Note 2: Note 3: Note 4: Note 5:
SYMBOL tCP
CONDITIONS (Note 2) (Note 3) (Note 4)
MIN
TYP 488 648 158.4 50%
MAX
UNITS ns
45% tOD1 tOD2 tR, tF tROPW (Note 5) 50
55% 50 50 10
ns ns ns ns ns
The timing parameters in this table are guaranteed by design (GBD). E1 or 2048kHz mode. DS1mode. 6312kHz mode. 100pF load.
Figure 10-4. BITS Receiver Timing Diagram
tCP RCLK tOD1 RSER tOD2 ROUT tF tR
19-4546; Rev 9; 5/09
208 of 227
DS3100
Table 10-12. BITS Transmitter Timing
(VDD = 1.8V 10%, VDDIO = 3.3V 5%, TA = -40C to +85C.) (Note 1) (See Figure 10-5.)
PARAMETER TCLK Period TCLK High Time TCLK Low Time TSER, TIN Rise and Fall Times TSER, TIN to TCLK Setup Time TSER, TIN to TCLK Hold Time TCLK to TOUT Delay TCLK, TOUT Rise and Fall Times
Note 1: Note 2: Note 3: Note 4:
SYMBOL tCP tCH tCL tR, tF tSU tHD tOD tR, tF
CONDITIONS (Note 2) (Note 3)
MIN
TYP 488 648
MAX
UNITS ns ns ns ns ns ns ns ns
125 125 20 20 (Note 4) 20 tCH - 5 50 10
The timing parameters in this table are guaranteed by design (GBD). E1 or 2048kHz mode. DS1mode. 100pF load.
Figure 10-5. BITS Transmitter Timing Diagram
tCP tR TCLK tSU TSER tHD tSU TIN
(frame sync or multiframe sync)
tF
tCL
tCH
tOD
tHD
TOUT
19-4546; Rev 9; 5/09
209 of 227
DS3100
10.5
Parallel Interface Timing
Table 10-13. Parallel Interface Timing
(VDD = 1.8V 10%, VDDIO = 3.3V 5%, TA = -40C to +85C.) (Note 1) (See Figure 10-6 and Figure 10-7.)
PARAMETER Address Setup to RD, WR, DS Active ALE Setup to RD, WR, DS Active Address Setup to ALE Inactive Address Hold from ALE Inactive ALE Pulse Width Address Hold from RD, WR, DS Inactive CS Setup to RD, WR, DS Active Data Valid from RD, DS Active RD, WR, DS Pulse Width if not Using RDY Handshake RD, WR, DS Delay from RDY Active Data Output High Impedance from RD, DS Inactive Data Output Enabled from RD, DS Active CS Hold from RD, WR, DS Inactive Data Setup to WR, DS Inactive Data Hold from WR, DS inactive RDY Active from RD, WR, DS Active RDY Inactive from RD, WR, DS Inactive RDY Output Enabled from CS Active RDY Output High Impedance from CS Inactive RDY Ending High Pulse Width R/W Setup to DS Active R/W Hold from DS Inactive
Note 1: Note 2: Note 3: Note 4: Note 5:
SYMBOL t1a t1b t2 t3 t4 t5 t6 t8 t9a t9b t10 t11 t12 t13 t14 t15 t16 t17 t18 t19 t20 t21
CONDITIONS (Note 2) (Notes 2, 3) (Notes 2, 3) (Notes 2, 3) (Notes 2, 3) (Note 2) (Note 2) (Note 2) (Notes 2, 4) (Note 2) (Notes 2, 5) (Note 2) (Note 2) (Note 2) (Note 2) (Note 2) (Note 2) (Note 2) (Note 2) (Note 2) (Note 2) (Note 2)
MIN 10 10 2 2 5 0 0
TYP
MAX
UNITS ns ns ns ns ns ns ns ns ns ns
80 90 15 2 2 0 10 5 10 0 10
ns ns ns ns ns ns ns ns ns ns ns ns
10 10 10
2 2 2
The timing parameters in this table are guaranteed by design (GBD). The input/output timing reference level for all signals is VDD/2. Transition time (80/20%) on RD, WR, and CS inputs is 5ns max. Multiplexed mode timing only. Timing required if not using RDY handshake. D[7:0] output valid until not driven.
19-4546; Rev 9; 5/09
210 of 227
DS3100
Figure 10-6. Parallel Interface Timing Diagram (Nonmultiplexed)
t1a Address t6 CS t8 Data Out AD[7:0] t11 Data In AD[7:0] R/W RD WR DS t20 t9a t13 t14 t10 t12
t5
t21
t17 t9b RDY t15 t16 t19
t18
19-4546; Rev 9; 5/09
211 of 227
DS3100
Figure 10-7. Parallel Interface Timing Diagram (Multiplexed)
t1a Address t2 ALE t4 t1b CS t6 Data Out AD[7:0] t11 Data In AD[7:0] R/W RD WR DS t20 t9a t21 t13 t14 t8 t10 t12 t3 t5
t17 t9b RDY t15 t16 t19
t18
19-4546; Rev 9; 5/09
212 of 227
DS3100
10.6
SPI Interface Timing
Table 10-14. SPI Interface Timing
(VDD = 1.8V 10%, VDDIO = 3.3V 5%, TA = -40C to +85C.) (Note 1) (See Figure 10-8.)
PARAMETER (Note 2) SCLK Frequency SCLK Cycle Time CS Setup to First SCLK Edge CS Hold time After Last SCLK Edge SCLK High Time SCLK Low Time SDI Data Setup Time SDI Data Hold Time SDO Enable Time (High-Impedance to Output Active) SDO Disable Time (Output Active to High Impedance) SDO Data Valid Time SDO Data Hold Time After Update SCLK Edge
Note 1: Note 2:
SYMBOL fBUS tCYC tSUC tHDC tCLKH tCLKL tSUI tHDI tEN tDIS tDV tHDO
MIN 166 15 15 80 80 5 15 0
TYP
MAX 6
25 40 5
UNITS MHz ns ns ns ns ns ns ns ns ns ns ns
The timing parameters in this table are guaranteed by design (GBD). All timing is specified with 100 pF load on all SPI pins.
Figure 10-8. SPI Interface Timing Diagram
CPHA = 0
CS tSUC SCLK, CPOL=0 SCLK, CPOL=1 tSUI SDI SDO tEN tHDO tCYC tCLKL tCLKH tCLKL tHDI tCLKH tHDC
tDV
tDIS
CPHA = 1
CS tSUC SCLK, CPOL=0 SCLK, CPOL=1 tCYC tCLKL tCLKH tCLKL tSUI SDI SDO tEN tHDO tCLKH tHDI tDV tDIS
tHDC
19-4546; Rev 9; 5/09
213 of 227
DS3100
10.7
JTAG Interface Timing
Table 10-15. JTAG Interface Timing
(VDD = 1.8V 10%, VDDIO = 3.3V 5%, TA = -40C to +85C.) (Note 1) (See Figure 10-9.)
PARAMETER JTCLK Clock Period JTCLK Clock High/Low Time (Note 2) JTCLK to JTDI, JTMS Setup Time JTCLK to JTDI, JTMS Hold Time JTCLK to JTDO Delay JTCLK to JTDO High-Impedance Delay (Note 3) JTRST Width Low Time
Note 1: Note 2: Note 3:
SYMBOL t1 t2/t3 t4 t5 t6 t7 t8
MIN 50 50 50 2 2 100
TYP 1000 500
MAX
50 50
UNITS ns ns ns ns ns ns ns
The timing parameters in this table are guaranteed by design (GBD). Clock can be stopped high or low. Not tested during production test.
Figure 10-9. JTAG Timing Diagram
t1 t2 JTCLK t3
t4
t5
JTDI, JTMS, JTRST t6 t7
JTDO
JTRST
t8
19-4546; Rev 9; 5/09
214 of 227
DS3100
11.
PIN ASSIGNMENTS
Table 11-1 lists the DS3100 pin assignments sorted in alphabetical order by pin name. Figure 11-1 and Figure 11-2 show pin assignments arranged by pin number.
Table 11-1. Pin Assignments Sorted by Signal Name
PIN NAME A[0] A[1] A[2] A[3] A[4] A[5] A[6] A[7] A[8] AD[0] AD[1] AD[2] AD[3] AD[4] AD[5] AD[6] AD[7] ALE AVDD_PLL1 AVDD_PLL2 AVDD_PLL3 AVDD_PLL4 AVSS_PLL1 AVSS_PLL2 AVSS_PLL3 AVSS_PLL4 CPHA CPOL CS DS DVDD DVSS GPIO1 GPIO2 GPIO3 GPIO4 HIZ IC1 IC10 IC11 IC12 19-4546; Rev 9; 5/09 PIN NUMBER H16 H15 G16 H14 G15 F16 G14 F15 E16 E15 D16 C16 D15 C15 E14 D14 C14 K14 D1 E1 F1 G1 D2 E3 G2 G3 D14 C14 J16 J14 H3 P8 E2 F3 H2 J1 R14 A10 B12 A13 C12 BUS MODES Parallel-Only Parallel-Only Parallel-Only Parallel-Only Parallel-Only Parallel-Only Parallel-Only Parallel-Only Parallel-Only Parallel-Only Parallel-Only Parallel-Only Parallel-Only Parallel-Only Parallel-Only Parallel-Only Parallel-Only Parallel-Only All All All All All All All All SPI-Only SPI-Only All Parallel-Only All All All All All All All All All All All SIGNAL TYPE High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Low-Speed Digital Low-Speed Digital High-Speed Digital High-Speed Digital Power Supply Power Supply Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital 215 of 227
DS3100 PIN NAME IC13 IC14 IC1A IC2 IC2A IC3 IC4 IC5NEG IC5POS IC6NEG IC6POS IC7 IC8 IC9 IFSEL[0] IFSEL[1] IFSEL[2] INTREQ JTCLK JTDI JTDO JTMS JTRST MASTSLV MCLK1 MCLK2 N.C. OC1 OC10 OC11 OC2 OC3 OC4 OC5 OC6NEG OC6POS OC7NEG OC7POS OC8NEG OC8POS OC9 R/W RCLK1 RCLK2 RD RDY REFCLK 19-4546; Rev 9; 5/09 PIN NUMBER B13 A14 P6 B10 P7 C10 A11 A5 B5 A4 B4 B11 C11 A12 N1 N2 P1 A15 R8 R9 P9 T9 T8 R11 F2 T10 C13, F14, P12 C6 B9 C9 A7 B7 C7 A8 A3 B3 C1 C2 B8 C8 A9 J15 K1 R10 J14 B15 H1 BUS MODES All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All Parallel-Only All All Parallel-Only Parallel-Only All SIGNAL TYPE High-Speed Digital High-Speed Digital Low-Speed Analog High-Speed Digital Low-Speed Analog High-Speed Digital High-Speed Digital High-Speed Analog High-Speed Analog High-Speed Analog High-Speed Analog High-Speed Digital High-Speed Digital High-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital No Connection High-Speed Digital Low-Speed Digital Low-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Digital High-Speed Analog High-Speed Analog High-Speed Analog High-Speed Analog Low-Speed Analog Low-Speed Analog Low-Speed Digital High-Speed Digital Low-Speed Digital Low-Speed Digital High-Speed Digital High-Speed Digital Low-Speed Digital 216 of 227
DS3100 PIN NAME RESREF ROUT1 ROUT2 RRING1 RRING2 RSER1 RSER2 RST RTIP1 RTIP2 RVDD_P1 RVDD_P2 RVSS_P1 RVSS_P2 SCLK SDI SDO SONSDH SRCSW SRFAIL SYNC2K TCLK1 TCLK2 THZE1 THZE2 TIN1 TIN2 TM1 TM2 TOUT1 TOUT2 TRING1 TRING2 TSER1 TSER2 TST_RA1 TST_RA2 TST_RB1 TST_RB2 TST_RC1 TST_RC2 TST_TA1 TST_TA2 TST_TB1 TST_TB2 TST_TC1 TST_TC2 19-4546; Rev 9; 5/09 PIN NUMBER T7 K2 P10 R5 L15 J3 T11 B6 T5 L16 T4 M15 P5 M14 C16 D16 E15 M3 M2 J2 B14 L2 T12 K3 T14 L1 R12 R13 T15 M1 P11 R2, T2 P15, P16 L3 T13 R6 L14 T6 K16 R7 K15 P2 R15 N3 P13 P3 P14 BUS MODES All All All All All All All All All All All All All All SPI-Only SPI-Only SPI-Only All All All All All All All All All All All All All All All All All All All All All All All All All All All All All All SIGNAL TYPE Low-Speed Analog Low-Speed Digital Low-Speed Digital Low-Speed Analog Low-Speed Analog Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Analog Low-Speed Analog Power Supply Power Supply Power Supply Power Supply Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Low-Speed Digital Test, Wire Low Test, Wire Low Low-Speed Digital Low-Speed Digital Low-Speed Analog Low-Speed Analog Low-Speed Digital Low-Speed Digital Test, Do Not Connect Test, Do Not Connect Test, Do Not Connect Test, Do Not Connect Test, Do Not Connect Test, Do Not Connect Test, Do Not Connect Test, Do Not Connect Test, Do Not Connect Test, Do Not Connect Test, Do Not Connect Test, Do Not Connect 217 of 227
DS3100 PIN NAME TTIP1 TTIP2 TVDD_P1 TVDD_P2 TVSS_P1 TVSS_P2 VDD VDD_ICDIFF VDD_OC6 VDD_OC7 VDDIO PIN NUMBER R3, T3 N15, N16 R4 M16 P4 N14 D6, D8, D9, D11, E6, E11, F4, F5, F12, F13, H4, H13, J4, J13, L4, L5, L12, L13, M6, M11, N6, N8, N9, N11 A6 B2 C3 B1, B16, D7, D10, E7-E10, G4, G5, G12, G13, H5, H12, J5, J12, K4, K5, K12, K13, M7, M8, M9, M10, N7, N10, R1, R16 A1, A16, D4, D5, D12, D13, E4, E5, E12, E13, F6-F11, G6-G11, H6-H11, J6-J11, K6-K11, L6-L11, M4, M5, M12, M13, N4, N5, N12, N13, T1, T16 C4 A2 D3 C5 J15 BUS MODES All All All All All All All All All All All SIGNAL TYPE Low-Speed Analog Low-Speed Analog Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply
VSS
All
Power Supply
VSS_ICDIFF VSS_OC6 VSS_OC7 WDT WR
All All All All Parallel-Only
Power Supply Power Supply Power Supply Low-Speed Analog High-Speed Digital
19-4546; Rev 9; 5/09
218 of 227
DS3100
Figure 11-1. DS3100 Pin Assignment--Left Half
1 A B C D E F G H J K L M N P R T
VSS VDDIO OC7NEG
2
VSS_OC6 VDD_OC6 OC7POS
3
OC6NEG OC6POS VDD_OC7
4
IC6NEG IC6POS VSS_ICDIFF
5
IC5NEG IC5POS WDT
6
VDD_ICDIFF RST OC1
7
OC2 OC3 OC4
8
OC5 OC8NEG OC8POS
AVDD_PLL1 AVDD_PLL2 AVDD_PLL3 AVDD_PLL4 REFCLK GPIO4 RCLK1 TIN1 TOUT1 IFSEL[0]
AVSS_PLL1 GPIO1 MCLK1 AVSS_PLL3 GPIO3 SRFAIL ROUT1 TCLK1 SRCSW IFSEL[1]
VSS_OC7 AVSS_PLL2 GPIO2 AVSS_PLL4 DVDD RSER1 THZE1 TSER1 SONSDH TST_TB1
VSS VSS VDD VDDIO VDD VDD VDDIO VDD VSS VSS
VSS VSS VDD VDDIO VDDIO VDDIO VDDIO VDD VSS VSS
VDD VDD VSS VSS VSS VSS VSS VSS VDD VDD
VDDIO VDDIO VSS VSS VSS VSS VSS VSS VDDIO VDDIO
VDD VDDIO VSS VSS VSS VSS VSS VSS VDDIO VDD
IFSEL[2] VDDIO VSS
TST_TA1 TRING1 TRING1
TST_TC1 TTIP1 TTIP1
TVSS_P1 TVDD_P1 RVDD_P1
RVSS_P1 RRING1 RTIP1
IC1A TST_RA1 TST_RB1
IC2A TST_RC1 RESREF
DVSS JTCLK JTRST
1
2
3
4
5
6
7
8
High-Speed Analog Low-Speed Analog High-Speed Digital Low-Speed Digital VDD 3.3V VDD 1.8V Analog VDD 3.3V Analog VDD 1.8V VSS Analog VSS N.C. = No Connection. Lead is not connected to anything inside the device.
19-4546; Rev 9; 5/09
219 of 227
DS3100
Figure 11-2. DS3100 Pin Assignment--Right Half
9
OC9 OC10 OC11
10
IC1 IC2 IC3
11
IC4 IC7 IC8
12
IC9 IC10 IC12
13
IC11 IC13 N.C.
14
IC14 SYNC2K AD[7]/CPOL
15
INTREQ RDY AD[4]
16
VSS VDDIO AD[2]/SCLK
A B C D E F G H J K L M N P R T
VDD VDDIO VSS VSS VSS VSS VSS VSS VDDIO VDD
VDDIO VDDIO VSS VSS VSS VSS VSS VSS VDDIO VDDIO
VDD VDD VSS VSS VSS VSS VSS VSS VDD VDD
VSS VSS VDD VDDIO VDDIO VDDIO VDDIO VDD VSS VSS
VSS VSS VDD VDDIO VDD VDD VDDIO VDD VSS VSS
AD[6]/CPHA AD[5] N.C. A[6] A[3] RD/DS ALE TST_RA2 RVSS_P2 TVSS_P2
AD[3] AD[0]/SDO A[7] A[4] A[1] WR/R/W TST_RC2 RRING2 RVDD_P2 TTIP2
AD[1] / SDI A[8] A[5] A[2] A[0] CS TST_RB2 RTIP2 TVDD_P2 TTIP2
JTDO JTDI JTMS
ROUT2 RCLK2 MCLK2
TOUT2 MASTSLV RSER2
N.C. TIN2 TCLK2
TST_TB2 TM1 TSER2
TST_TC2 HIZ THZE2
TRING2 TST_TA2 TM2
TRING2 VDDIO VSS
9
10
11
12
13
14
15
16
High-Speed Analog Low-Speed Analog High-Speed Digital Low-Speed Digital VDD 3.3V VDD 1.8V Analog VDD 3.3V Analog VDD 1.8V VSS Analog VSS N.C. = No Connection. Lead is not connected to anything inside the device.
19-4546; Rev 9; 5/09
220 of 227
DS3100
12.
12.1
PACKAGE INFORMATION
256-Pin CSBGA (17mm x 17mm)
PACKAGE TYPE 256 CSBGA PACKAGE CODE -- DOCUMENT NO. 21-0315
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages.
19-4546; Rev 9; 5/09
221 of 227
DS3100
13.
THERMAL INFORMATION
Table 13-1. Thermal Properties, Natural Convection
PARAMETER Ambient Temperature (Note 1) Junction Temperature Theta-JA (JA), Still Air (Note 2) Theta-JB (JB), Still Air Theta-JC (JC), Still Air Psi-JB Psi-JT
Note 1: Note 2:
MIN -40 -40
TYP
MAX +85 +125
UNITS C C C/W C/W C/W C/W C/W
26.7 14.0 11.0 13.5 0.7
The package is mounted on a four-layer JEDEC standard test board with no airflow and dissipating maximum power. Theta-JA (JA) is the junction to ambient thermal resistance, when the package is mounted on a four-layer JEDEC standard test board with no airflow and dissipating maximum power.
19-4546; Rev 9; 5/09
222 of 227
DS3100
14.
GLOSSARY
The 12.800MHz TCXO, OCXO, or other crystal oscillator connected to the REFCLK pin. The stability of the T0 DPLL in free-run and holdover modes is a function of the stability of this oscillator. A 204.8MHz clock synthesized from the local oscillator and frequency adjusted by the XOFREQ register setting. One of the 14 input clocks labeled IC1 to IC14. One of the 11 output clocks labeled OC1 to OC11. The input clock to which the DPLL is currently phase locked. An input clock that has no alarms declared in the corresponding ISR register. A clock whose frequency is within the hard limit set in ILIMIT or CLIMIT and that does not have an inactivity alarm. An input clock that has one or more alarms declared in the corresponding ISR register. EXTSW = 1 in MCR10.
Local Oscillator
Master Clock
Input Clock Output Clock Selected Reference Valid Clock
Invalid Clock External Reference Switching Mode
19-4546; Rev 9; 5/09
223 of 227
DS3100
15.
ACRONYMS AND ABBREVIATIONS
Alarm Indication Signal Alternate Mark Inversion Analog Phase-Locked Loop Building Integrated Timing Supply Bipolar Violation Digital Frequency Synthesis Digital Phase Locked Loop Extended Superframe Excessive Zeros Gigabit Ethernet Input/Output Loss of Signal Low-Voltage-Differential Signal Low-Voltage Positive Emitter-Coupled Logic Maximum Time Interval Error Oven-Controlled Crystal Oscillator Out-of-Frame Alignment Phase Build-Out Phase/Frequency Detector Phase-Locked Loop Parts per Billion Parts per Million Peak-to-Peak Root-Mean-Square Remote Alarm Indication Read-Only Read/Write Synchronous Digital Hierarchy SDH Equipment Clock Synchronous Equipment Timing Source Superframe Synchronous Optical Network Synchronization Status Message Synchronization Supply Unit synchronous Transport Module Time Deviation Temperature-Compensated Crystal Oscillator Unit Interval Unit Interval, Peak to Peak
AIS AMI APLL BITS BPV DFS DPLL ESF EXZ GbE I/O LOS LVDS LVPECL MTIE OCXO OOF PBO PFD PLL ppb ppm pk-pk RMS RAI RO R/W SDH SEC SETS SF SONET SSM SSU STM TDEV TCXO UI UIP-P
16.
TRADEMARK ACKNOWLEDGEMENTS
ACCUNET is a registered trademark of AT&T. SPI is a trademark of Motorola, Inc. Telcordia is a registered trademark of Telcordia Technologies.
19-4546; Rev 9; 5/09
224 of 227
DS3100
17. DATA SHEET REVISION HISTORY
REVISION NUMBER 0 REVISION DATE 062106 Initial release. Changed all occurrences of 0.5MHz (megahertz) to 0.5mHz (milliHertz). In Figure 3-1, corrected arrow directions between backplane and timing cards. In second-to-last paragraph of Section 7.5.2, changed LBxS = 1 to LBxS = 10. In Figure 7-7, edited figure so the TSYNC label does not cover up a portion of the TCLK wire. 1 092106 In Table 8-2, updated the color coding. DLIMIT2 register description changed to end in "2" not "1." In Table 8-3, BTCR1 (27h) bit 3 changed to "1"; BLCR1 address changed from 18h to 10h; BLCR2 bit 3 changed to "0"; BLCR3 bit 7 changed to "0"; BRIIR bits marked as read-only (i.e., underlined). Changed BRCR3 bit 5 to RSIGM; added description. BRCR5 register bit 0 name changed from "--" to "1." BTCR4 register description changed to end in "4" not "1." 2 3 121806 013007 Added GBD comments (Note 1) to AC timing characteristics in Section 10. In Table 6-10 deleted N6 from the VSS pin description (N6 is VDD) Updated spec name from G.pactiming to G.8261. In Table 6-4, edited the TTIP1/TRING1 and TTIP2/TRING2 pin descriptions to indicate that identical TTIP pins should be externally wired together, and identical TRING pins should be externally wired together. Edited Section 7.4 to indicate minimum high time or low time is 3ns or 30% of clock period, whichever is smaller. In Table 7-2 added indications that IC5 and IC6 can be CMOS/TTL inputs. Added note at the end of Section 7.7.1.7 to indicate that mini-holdover follows the manual holdover setting. Added hyperlink to Maxim app note HFAN-1.0 in Section 7.8.1. 4 030807 In the 125MHz row of Table 7-13, corrected a typo by changing "OC4 and OC5 only" to "OC5 only". Updated Figure 7-8 to correct a wiring mistake regarding the input to the "x16 Multiplier PLL". (Page 62) Updated Figure 7-10 to show the two TTIP pins connected together and the two TRING pins connected together. Added Note 2 to Table 10-4. Added Note 3 to Table 10-5. Updated Figure 10-3 and Table 10-7 and accompanying text to show new recommended external components. Updated Table 10-8 to clarify minimum high time and low time (and therefore duty cycle) for input clocks. DESCRIPTION PAGES CHANGED -- 1, 12, 24, 37, 38, 42 9 30 58 82 111 147 166 167 171 203, 206, 208, 209, 210, 213, 214 22 1 18
26 27 36 45 53
59 204 205 206 207
19-4546; Rev 9; 5/09
225 of 227
DS3100
REVISION NUMBER REVISION DATE DESCRIPTION In the Feature bullets, changed "G.812 Types I and III" to "G.812 Types I, III and IV". Deleted reference to IEEE 1596.3 standard from Table 1-1. Updated Figure 3-1 to show backplane traces going between timing cards. Edited Section 7.10.1 to improve clarity. (Pages) Edited Sections 7.10.5.1, 7.10.5.2, 7.10.6.1, and 7.10.6.2 to clarify when the BRCR and BTCR registers should be written during the receive framer and transmit formatter initialization processes. 5 032907 In Section 7.10.7.2, added text to describe the additional writes that must be done to optimize the BITS LIU transmitter when entering or leaving 2048kHz mode. Rewrote Section 7.15 to refer readers to the web or Telecom Support for the latest initialization scripts. In the BMCR bits 5 and 4 description, replaced "Values not listed are undefined." with "See Section 7.10.7.2 for write sequences that must be done when entering or leaving the 2048 kHz mode." BLCR2, BLCR3, BRCR5, BTCR1: For each bit that should always be set to zero or set to one, added a bit description to remind the reader that these bits must be set to zero/one. In register BCCR5, updated the description of bits 5 and 4 to indicate that the device squelches and increments the activity monitor on zeros rather than invalidating. Edited Section 7.7.6 and the DLIMIT1 and DLIMIT3:FLLOL descriptions to indicate that the T4 DPLL's hard limit is fixed at 80ppm and is not controlled by the HARDLIM field. In Section 7.7.2, corrected a typo to say the T4 DPLL only operates in revertive switching mode rather than "does not have revertive switching mode." Edited the OFREQ1 through OFREQ7 fields in the OCR registers to indicate that if the T4 DPLL is configured for 62.5MHz, then OFREQ = 1100 specifies T4 APLL frequency divided by 10 to give an output frequency of 25MHz. Added a 25MHz row to Table 7-13. In Table 10-2, changed IDD18 (Note 2) to 129mA typ, 152mA max; changed IDD18 (Note 3) to 130mA typ, 154mA max; changed IDD33 (Note 2) to 36mA typ, 53mA max; changed IDD33 (Note 3) to 124mA typ, 145mA max. The changes are necessary to account for the power consumption of the differential I/O, which were not functional in rev A1 parts. Also changed IDDR1 from 29mA typ to 35mA typ. In Table 10-3 changed VDD to VDDIO in the VOH max spec and in Note 1. In Table 10-4, changed VOHLVDS to 1.45V typ, 1.65V max; added VOLLVDS 1.1V typ; changed VOSLVDS to 1.08V min, 1.28V typ, 1.45V max. In Table 10-5, deleted specs IIHPECL and IIILPECL specs and in Note 2 changed VDD to VDDIO. In Table 10-6 in the VIHAMI spec, changed max from VDD+0.3 to VDDIO+0.3 and deleted the IAMIOUT, VOHAMI, and VOLAMI specs because the specs in Table 7-22 and Figure 7-17 are sufficient to govern output signal performance for OC8. In Table 7-13, updated many of the typical rms and peak-to-peak jitter numbers to match rev A2 device performance. In Table 7-9, corrected typo, 68.376 to 68.736. PAGES CHANGED 1 7 9 59 68-71
72 80 149
155, 156, 167, 168
154
39, 111, 118
36
123 50
6
060607
203
204 204 205
206
50 48
19-4546; Rev 9; 5/09
226 of 227
DS3100
REVISION NUMBER REVISION DATE DESCRIPTION Added pin N5 to the VSS row in Table 6-10. Edited Section 7.13 to emphasize the need for the RST pin to be asserted once after power-up and to describe the need to wait at least 100s after reset is deasserted before initializing the device. In Section 8.5, changed "080h + 16h = 96h" to "080h + 1Ah = 9Ah." In Table 8-3, changed BTCR1 bit 3 from "1" to "--". 7 012108 In the BLCR4 description, changed the TPD and RPD bit descriptions to show they are set to 0 rather than 1. In the BTMMR description for the TID bit, changed "receiver" to "transmitter." In the BTCR1, changed bit 3 from "1" to "--". In BTSR1 and BTIER1, corrected typo for bit 1 and changed "--" to "LOTCC". In registers BRSiAF, BRSiNAF, BRRAI, BRSa4 through BRSa8, BTSiAF, BTSiNAF, BTRAI, and BTSa4 through BTSa8, corrected bit-ordering typo so that bit 7 of the register contains the "F15" or "F14" bit while bit 0 of the register contains the "F1" or "F0" bit. In Table 10-14, changed tCYC to 166ns min, tCLKH to 80ns min, and tCLKL to 80ns min to match fBUS max of 6MHz. On page 1 and various locations in the document, added mention of Stratum 2 compliance, expanded G.812 compliance to Types I - IV, and added G.8262 EEC compliance. In Table 1-1, added G.8262. 9 5/09 In Table 6-1, indicated that differential inputs IC5 and IC6 could be configured as singled-ended CMOS/TTL and how to do it. In Table 7-1, deleted the initial offset row since it is not an oscillator requirement. Next to Table 8-1, added note indicating systems must be able to access entire address range 0-1FFh. 1, 7, 15, 25, 81 PAGES CHANGED 22 79
147 157 163 168 181 185-188, 193-196 213
8
062508
19-4546; Rev 9; 5/09
227 of 227

▲Up To Search▲

Price & Availability of DS3100GN

	To Download DS3100GN Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .